Use the RFmxCDMA2k properties to access options for configuring and fetching measurements.

© 2015–2025 National Instruments Corporation. All rights reserved.

ACP:Advanced:Far IF Output Power Offset (dB)
Specifies the offset by which to adjust the IF output power level for offset channels that are far from the carrier channel to improve the dynamic range. This value is expressed in dB. This property is used only if you set the ACP Meas Method property to Dynamic Range and set the ACP IF Output Power Offset Auto property to False.
ACP:Advanced:IF Output Power Offset Auto
Specifies whether the measurement computes an IF output power level offset for the offset channels to improve the dynamic range of the ACP measurement. This property is used only if you set the ACP Meas Method property to Dynamic Range.
ACP:Advanced:Near IF Output Power Offset (dB)
Specifies the offset by which to adjust the IF output power level for offset channels that are near the carrier channel to improve the dynamic range. This value is expressed in dB. This property is used only if you set the ACP Meas Method property to Dynamic Range and set the ACP IF Output Power Offset Auto property to False.
ACP:Advanced:Sequential FFT Size
Specifies the FFT size, when you set the ACP Meas Method property to Sequential FFT.
ACP:All Traces Enabled
Specifies whether to enable the traces to be stored and retrieved after performing the ACP measurement.
ACP:Averaging:Count
Specifies the number of acquisitions used for averaging when you set the ACP Averaging Enabled property to True.
ACP:Averaging:Enabled
Specifies whether to enable averaging for the ACP measurement.
ACP:Averaging:Type
Specifies the averaging type for averaging multiple spectrum acquisitions. The averaged spectrum is used for ACP measurement.
ACP:Carrier:Integration Bandwidth (Hz)
Returns the ACP carrier integration bandwidth. This value is expressed in Hz.
ACP:FFT:Overlap (%)
Returns the number of samples to overlap between consecutive chunks while performing FFT.
ACP:FFT:Overlap Mode
Specifies how the FFT overlap is applied to the acquired samples.
ACP:Measurement Enabled
Specifies whether to enable the ACP measurement.
ACP:Measurement Method
Specifies the method for performing the ACP measurement.
ACP:Noise Compensation Enabled
Specifies whether to enable compensation of the channel powers for the inherent noise floor of the signal analyzer.
ACP:Number of Analysis Threads
Specifies the maximum number of threads used for parallelism for the ACP measurement.
ACP:Offset:Frequency (Hz)
Returns the frequency of an ACP offset channel relative to the carrier frequency. This value is expressed in Hz.
ACP:Offset:Integration Bandwidth (Hz)
Returns the integration bandwidth of an ACP offset channel. This value is expressed in Hz.
ACP:Offset:Number of Offsets
Specifies the number of offset channels.
ACP:RBW Filter:Auto Bandwidth
Specifies whether the measurement computes the RBW.
ACP:RBW Filter:Bandwidth (Hz)
Specifies the bandwidth of the RBW filter used to sweep the acquired signal when you set the ACP RBW Auto property to False. This value is expressed in Hz.
ACP:RBW Filter:Type
Specifies the shape of the digital RBW filter.
ACP:Results:Carrier:Absolute Power (dBm)
Returns the absolute measured carrier power. This value is expressed in dBm.
ACP:Results:Lower Offset:Absolute Power (dBm)
Returns the absolute measured lower offset channel power. This value is expressed in dBm.
ACP:Results:Lower Offset:Relative Power (dB)
Returns the lower offset channel power measured relative to the carrier absolute integrated power. This value is expressed in dB.
ACP:Results:Upper Offset:Absolute Power (dBm)
Returns the absolute measured upper offset channel power. This value is expressed in dBm.
ACP:Results:Upper Offset:Relative Power (dB)
Returns the upper offset channel power measured relative to the carrier absolute integrated power. This value is expressed in dB.
ACP:Sweep Time:Auto
Specifies whether the measurement computes the sweep time.
ACP:Sweep Time:Interval (s)
Specifies the sweep time when you set the ACP Sweep Time Auto property to False. This value is expressed in seconds.
Advanced:Auto Level Initial Reference Level (dBm)
Specifies the initial reference level that the RFmxCDMA2k Auto Level VI uses to estimate the peak power of the input signal. This value is expressed in dBm.
Advanced:Limited Configuration Change
Specifies the set of properties that are considered by RFmx in the locked signal configuration state.
Band Class
Specifies the band in which the channel is located as defined in Section: 1.5, Table 1.5- Band Class List, of the 3GPP2 C.S0057-F specification v1.0.
CDA:All Traces Enabled
Specifies whether to enable the traces to be stored and retrieved after performing the code domain analysis (CDA).
CDA:Base Spreading Factor
Specifies the base spreading factor used to calculate the code domain power traces.
CDA:IQ Gain Imbalance Removal Enabled
Specifies whether to remove the I/Q gain imbalance before the code domain analysis (CDA) measurement.
CDA:IQ Offset Removal Enabled
Specifies whether to remove I/Q offset before the code domain analysis (CDA) measurement.
CDA:IQ Quadrature Error Removal Enabled
Specifies whether to remove the I/Q quadrature error before the code domain analysis (CDA) measurement.
CDA:Measurement Channel:Branch
Specifies the branch of a channel subject to channel specific analysis.
CDA:Measurement Channel:Walsh Code Length
Specifies the Walsh code length of a channel subject to channel specific analysis.
CDA:Measurement Channel:Walsh Code Number
Specifies the Walsh code number of a channel subject to channel specific analysis.
CDA:Measurement Enabled
Specifies whether to enable the code domain analysis (CDA) measurement.
CDA:Measurement Length (slots)
Specifies the duration of code domain measurement. This value is expressed in slots.
CDA:Measurement Offset (slots)
Specifies the measurement offset to skip from the synchronization boundary. The synchronization boundary is specified by the CDA Sync Mode property. This value is expressed in slots.
CDA:Power Unit
Specifies the measurement unit of the measured code domain power results.
CDA:Receive Filter Enabled
Specifies whether to enable the received filter for the code domain analysis (CDA) measurement. Use this property to disable the filter, if the received signal is already filtered.
CDA:Results:Chip Rate Error (ppm)
Returns the chip rate error. This value is expressed in parts per million (ppm).
CDA:Results:Frequency Error (Hz)
Returns the frequency error. This value is expressed in Hz.
CDA:Results:I Mean Active Power (dB or dBm)
Returns the average power of all active code channels measured on the I-branch. If you set the CDA Pwr Unit property to dBm, this measurement returns the absolute measured power; otherwise, this measurement returns a value relative to the CDA Result Total Power property.
CDA:Results:I Peak Inactive Power (dB or dBm)
Returns the maximum measured code power among the set of inactive channels on the I-branch and in the code domain of the base spreading factor. If you set the CDA Pwr Unit property to dBm, this measurement returns the absolute measured power; otherwise, this measurement returns a value relative to the CDA Result Total Power property.
CDA:Results:I/Q Gain Imbalance (dB)
Returns the I/Q gain imbalance of the composite signal averaged over all measured slots. This value is expressed in dB.
CDA:Results:I/Q Origin Offset (dB)
Returns the I/Q origin offset of the composite signal averaged over all measured slots. This value is expressed in dB.
CDA:Results:I/Q Quadrature Error (deg)
Returns the I/Q quadrature error of the composite signal averaged over all measured slots. This value is expressed in degrees.
CDA:Results:Mean Active Power (dB or dBm)
Returns the average power of all active code channels. If you set the CDA Pwr Unit property to dBm, this measurement returns the absolute measured power; otherwise, this measurement returns a value relative to the CDA Result Total Power property.
CDA:Results:Mean Inactive Power (dB or dBm)
Returns the average code power, measured among the set of inactive channels, in the code domain of the base spreading factor. If you set the CDA Pwr Unit property to dBm, this measurement returns the absolute measured power; otherwise, this measurement returns a value relative to the CDA Result Total Power property.
CDA:Results:Mean Pilot Power (dB or dBm)
Returns the mean power of the R-PICH.
CDA:Results:Mean Symbol Power (dB or dBm)
Returns the mean symbol power of the configured measurement channel. This value is expressed in dB, when you set the CDA Pwr Unit property to dB, and in dBm, when you set the CDA Pwr Unit property to dBm.
CDA:Results:Peak Active Power (dB or dBm)
Returns the maximum power among all active code channels. If you set the CDA Pwr Unit property to dBm, this measurement returns the absolute measured power; otherwise, this measurement returns a value relative to the CDA Result Total Power property.
CDA:Results:Peak Inactive Power (dB or dBm)
Returns the maximum measured code power, measured among the set of inactive channels, in the code domain of the base spreading factor. If you set the CDA Pwr Unit property to dBm, this measurement returns the absolute measured power; otherwise, this measurement returns a value relative to the CDA Result Total Power property.
CDA:Results:Peak Symbol EVM (%)
Returns the peak symbol EVM of the configured measurement channel. This value is expressed as a percentage.
CDA:Results:Q Mean Active Power (dB or dBm)
Returns the average power of all active code channels measured on the Q-branch. If you set the CDA Pwr Unit property to dBm, this measurement returns the absolute measured power; otherwise, this measurement returns a value relative to the CDA Result Total Power property.
CDA:Results:Q Peak Inactive Power (dB or dBm)
Returns the maximum measured code power among the set of inactive channels on the Q-branch and in the code domain of the base spreading factor. If you set the CDA Pwr Unit property to dBm, this measurement returns the absolute measured power; otherwise, this measurement returns a value relative to the CDA Result Total Power property.
CDA:Results:RMS Symbol EVM (%)
Returns the RMS symbol EVM of the configured measurement channel. This value is expressed as a percentage.
CDA:Results:RMS Symbol Magnitude Error (%)
Returns the RMS symbol magnitude error of the configured measurement channel. This value is expressed as a percentage.
CDA:Results:RMS Symbol Phase Error (deg)
Returns the RMS symbol phase error of the configured measurement channel. This value is expressed in degrees.
CDA:Results:Total Active Power (dB or dBm)
Returns the sum of the powers of all active code channels. If you set the CDA Pwr Unit property to dBm, this measurement returns the absolute measured power; otherwise, this measurement returns a value relative to the CDA Result Total Power property.
CDA:Results:Total Power (dBm)
Returns the mean power of the received signal. This value is expressed in dBm.
CDA:Spectrum Inverted
Specifies whether the spectrum of the signal is inverted.
CDA:Synchronization Mode
Specifies whether the measurement is performed from the frame, slot, or symbol boundary.
CHP:All Traces Enabled
Specifies whether to enable the traces to be stored and retrieved after performing the CHP measurement.
CHP:Averaging:Count
Specifies the number of acquisitions used for averaging when you set the CHP Averaging Enabled property to True.
CHP:Averaging:Enabled
Specifies whether to enable averaging for the CHP measurement.
CHP:Averaging:Type
Specifies the averaging type for averaging multiple spectrum acquisitions. The averaged spectrum is used for the CHP measurement.
CHP:Integration Bandwidth (Hz)
Returns the CHP carrier integration bandwidth. This value is expressed in Hz.
CHP:Measurement Enabled
Specifies whether to enable the CHP measurement.
CHP:Number of Analysis Threads
Specifies the maximum number of threads used for parallelism for the CHP measurement.
CHP:RBW Filter:Auto Bandwidth
Specifies whether the measurement computes the RBW.
CHP:RBW Filter:Bandwidth (Hz)
Specifies the bandwidth of the RBW filter used to sweep the acquired signal when you set the CHP RBW Auto property to False. This value is expressed in Hz.
CHP:RBW Filter:Type
Specifies the shape of the digital RBW filter.
CHP:Results:Carrier:Absolute Power (dBm)
Returns the averaged CHP measured in the specified integration bandwidth. This value is expressed in dBm.
CHP:Sweep Time:Auto
Specifies whether the measurement computes the sweep time.
CHP:Sweep Time:Interval (s)
Specifies the sweep time when you set the CHP Sweep Time Auto property to False. This value is expressed in seconds.
Center Frequency (Hz)
Specifies the carrier frequency of the RF signal to acquire. The signal analyzer tunes to this frequency. This value is expressed in Hz.
Channel:Configuration Mode
Specifies whether to detect the channels automatically or to use a specified channel configuration.
Channel:User Defined:Branch
Specifies the branch on which a specific user-defined channel is mapped. This property is used only when you set the Channel Configuration Mode property to User Defined.
Channel:User Defined:Number of Channels
Specifies the number of user-defined channels. This property is used only when you set the Channel Configuration Mode property to User Defined.
Channel:User Defined:Walsh Code Length
Specifies the Walsh code length of a specific user-defined channel. This value is expressed in chips. This property is used only when you set the Channel Configuration Mode property to User Defined.
Channel:User Defined:Walsh Code Number
Specifies the Walsh code number of a specific user-defined channel. This property is used only when you set the Channel Configuration Mode property to User Defined.
External Attenuation (dB)
Specifies the attenuation of a switch or cable connected to the RF IN connector of the signal analyzer. This value is expressed in dB. For more information about attenuation, refer to the RF Attenuation and Signal Levels topic for your device in the NI RF Vector Signal Analyzers Help.
Link Direction
Specifies the link direction of the received signal.
ModAcc:All Traces Enabled
Specifies whether to enable the traces to be stored and retrieved after performing the modulation accuracy (ModAcc) measurement.
ModAcc:IQ Gain Imbalance Removal Enabled
Specifies whether to remove the I/Q gain imbalance before an EVM measurement.
ModAcc:IQ Offset Removal Enabled
Specifies whether to remove the I/Q offset before an EVM measurement.
ModAcc:IQ Quadrature Error Removal Enabled
Specifies whether to remove the I/Q quadrature error before an EVM measurement.
ModAcc:Measurement Enabled
Specifies whether to enable the modulation accuracy (ModAcc) measurement.
ModAcc:Measurement Length (slots)
Specifies the duration of the modulation accuracy (ModAcc) measurement. This value is expressed in slots.
ModAcc:Measurement Offset (slots)
Specifies the measurement offset to skip from the synchronization boundary. The synchronization boundary is specified by the ModAcc Sync Mode property. This value is expressed in slots.
ModAcc:Multi Carrier Filter:Enabled
Specifies whether to enable the multi carrier filter which can be used to improve ModAcc measurement quality in presence of neighboring carriers.
ModAcc:Receive Filter Enabled
Specifies whether to enable the received filter for the ModAcc measurement. For RC1/2, this property refers to the band-limiting filter specified in the Chapter 6.4.2.1 of 3GPP2 C.S0011-E. For RC3/4, this property refers to the complementary filter specified in the Chapter 6.4.2.2 of 3GPP2 C.S0011-E.
ModAcc:Results:Chip Rate Error (ppm)
Returns the chip rate error. This value is expressed in parts per million (ppm).
ModAcc:Results:Detected Channel:Branch
Returns the branch of the detected channel. If you set the Channel Configuration Mode property to User Defined, the property returns the branch of the configured channel.
ModAcc:Results:Detected Channel:Number of Detected Channels
Returns the total number of detected channels. If you set the Channel Configuration Mode property to User Defined, the property returns the number of configured channels.
ModAcc:Results:Detected Channel:Walsh Code Length
Returns the Walsh code length of the detected channel. If you set the Channel Configuration Mode property to User Defined, the property returns the Walsh code length of the configured channel.
ModAcc:Results:Detected Channel:Walsh Code Number
Returns the Walsh code number of the detected channel. If you set the Channel Configuration Mode property to User Defined, the property returns the Walsh code number of the configured channel.
ModAcc:Results:Frequency Error (Hz)
Returns the frequency error averaged over all measured slots. This value is expressed in Hz.
ModAcc:Results:I/Q Gain Imbalance (dB)
Returns the I/Q gain imbalance of the composite signal averaged over all measured slots. This value is expressed in dB.
ModAcc:Results:I/Q Origin Offset (dB)
Returns the I/Q origin offset of the composite signal averaged over all measured slots. This value is expressed in dB.
ModAcc:Results:I/Q Quadrature Error (deg)
Returns the I/Q quadrature error of the composite signal, averaged over all measured slots. This value is expressed in degrees.
ModAcc:Results:Peak Active CDE (dB)
Returns the maximum value among the code domain errors (CDEs) for all active channels. This value is expressed in dB. The active CDEs are computed by projecting the descrambled error vector onto the codes of each active channel. The active CDE is defined as the ratio of the mean power of the projection onto that code to the mean power of the composite reference waveform.
ModAcc:Results:Peak Active CDE Branch
Returns the branch of the channel corresponding to the value that the ModAcc Results Pk Active CDE property returns.
ModAcc:Results:Peak Active CDE Walsh Code Length
Returns the Walsh code length of the channel corresponding to the value that the ModAcc Results Pk Active CDE property returns.
ModAcc:Results:Peak Active CDE Walsh Code Number
Returns the Walsh code number of the channel corresponding to the value that the ModAcc Results Pk Active CDE property returns.
ModAcc:Results:Peak CDE (dB)
Returns the maximum value among the code domain errors (CDEs). This value is expressed in dB. The CDEs are computed by projecting the descrambled error vector onto the code domain at a specific spreading factor. The CDE for every code with a specific spreading factor is defined as the ratio of the mean power of the projection onto that code to the mean power of the composite reference waveform. A fixed spreading factor of 16 is used. The CDEs are computed separately for I and Q branches.
ModAcc:Results:Peak CDE Branch
Returns the branch corresponding to the value that the ModAcc Results Pk CDE property returns.
ModAcc:Results:Peak CDE Walsh Code Number
Returns the Walsh code number corresponding to the value that the ModAcc Results Pk CDE property returns.
ModAcc:Results:Peak EVM (%)
Returns the peak EVM of the composite signal. This value is expressed as a percentage.
ModAcc:Results:RMS EVM (%)
Returns the RMS EVM of the composite signal. This value is expressed as a percentage.
ModAcc:Results:RMS Magnitude Error (%)
Returns the RMS magnitude error of the composite signal. This value is expressed as a percentage.
ModAcc:Results:RMS Phase Error (deg)
Returns the RMS phase error of the composite signal. This value is expressed in degrees.
ModAcc:Results:Rho
Returns the correlation of the received signal with the reference signal normalized by the signal power. The value of Rho is between 0 and 1.0, inclusive. A value of 1.0 indicates that the received signal and the reference signal are perfectly correlated.
ModAcc:Results:Slot Timing Error (s)
Returns the measured timing error from the beginning of the acquisition to the location of the first slot acquired. This value is expressed in seconds.
ModAcc:Spectrum Inverted
Specifies whether the spectrum of the signal is inverted.
ModAcc:Synchronization Mode
Specifies whether the measurement is performed from the frame, slot, or symbol boundary.
OBW:All Traces Enabled
Specifies whether to enable the traces to be stored and retrieved after performing the OBW.
OBW:Averaging:Count
Specifies the number of acquisitions used for averaging when you set the OBW Averaging Enabled property to True.
OBW:Averaging:Enabled
Specifies whether to enable averaging for the OBW measurement.
OBW:Averaging:Type
Specifies the averaging type for averaging multiple spectrum acquisitions. The averaged spectrum is used for the OBW measurement.
OBW:Measurement Enabled
Specifies whether to enable the OBW measurement.
OBW:Number of Analysis Threads
Specifies the maximum number of threads used for parallelism for the OBW measurement.
OBW:RBW Filter:Auto Bandwidth
Specifies whether the measurement computes the RBW.
OBW:RBW Filter:Bandwidth (Hz)
Specifies the bandwidth of the RBW filter used to sweep the acquired signal when you set the OBW RBW Auto property to False. This value is expressed in Hz.
OBW:RBW Filter:Type
Specifies the shape of the digital RBW filter.
OBW:Results:Absolute Power (dBm)
Returns the absolute power measured in the OBW. This value is expressed in dBm.
OBW:Results:Occupied Bandwidth (Hz)
Returns the bandwidth that occupies 99% of the total signal power. This value is expressed in Hz.
OBW:Results:Start Frequency (Hz)
Returns the start frequency of the OBW. This value is expressed in Hz.
OBW:Results:Stop Frequency (Hz)
Returns the stop frequency of the OBW. This value is expressed in Hz.
OBW:Span (Hz)
Returns the frequency span of the OBW measurement. This value is expressed in Hz.
OBW:Sweep Time:Auto
Specifies whether the measurement computes the sweep time.
OBW:Sweep Time:Interval (s)
Specifies the sweep time when you set the OBW Sweep Time Auto property to False. This value is expressed in seconds.
QEVM:All Traces Enabled
Specifies whether to enable the traces to be stored and retrieved after performing the QEVM measurement.
QEVM:Averaging:Count
Specifies the number of measurements used for averaging when you set the QEVM Averaging Enabled property to True.
QEVM:Averaging:Enabled
Specifies whether to enable averaging for the QEVM measurement.
QEVM:IQ Gain Imbalance Removal Enabled
Specifies whether to remove I/Q gain imbalance before QEVM measurement.
QEVM:IQ Offset Removal Enabled
Specifies whether to remove I/Q offset before QEVM measurement.
QEVM:IQ Quadrature Error Removal Enabled
Specifies whether to remove I/Q quadrature error before QEVM measurement.
QEVM:Measurement Enabled
Specifies whether to enable the QEVM measurement.
QEVM:Measurement Length (chips)
Specifies the number of chips used for a single measurement.
QEVM:Number of Analysis Threads
Specifies the maximum number of threads used for parallelism for the QEVM measurement.
QEVM:Receive Filter Enabled
Specifies whether to enable the received filter for the QEVM measurement.
QEVM:Results:Maximum Chip Rate Error (ppm)
Returns the maximum chip rate error. This value is expressed in parts per million (ppm).
QEVM:Results:Maximum Frequency Error (Hz)
Returns the maximum frequency error of the received signal. This value is expressed in Hz.
QEVM:Results:Maximum I/Q Gain Imbalance (dB)
Returns the maximum I/Q gain imbalance of the received signal. This value is expressed in dB.
QEVM:Results:Maximum I/Q Origin Offset (dB)
Returns the maximum origin offset of the received signal. This value is expressed in dB.
QEVM:Results:Maximum I/Q Quadrature Error (deg)
Returns the maximum I/Q quadrature error (phase imbalance) of the received signal. This value is expressed in degrees.
QEVM:Results:Maximum Magnitude Error (%)
Returns the maximum magnitude error of the received signal. This value is expressed as a percentage.
QEVM:Results:Maximum Peak EVM (%)
Returns the maximum peak EVM of the received signal. This value is expressed as a percentage.
QEVM:Results:Maximum Phase Error (deg)
Returns the maximum phase error of the received signal. This value is expressed in degrees.
QEVM:Results:Maximum RMS EVM (%)
Returns the maximum RMS EVM of the received signal. This value is expressed as a percentage.
QEVM:Results:Mean Chip Rate Error (ppm)
Returns the mean chip rate error. This value is expressed in parts per million (ppm).
QEVM:Results:Mean Frequency Error (Hz)
Returns the mean averaged frequency error of the received signal. This value is expressed in Hz.
QEVM:Results:Mean I/Q Gain Imbalance (dB)
Returns the mean I/Q gain imbalance of the received signal. This value is expressed in dB.
QEVM:Results:Mean I/Q Origin Offset (dB)
Returns the mean averaged origin offset of the received signal. This value is expressed in dB.
QEVM:Results:Mean I/Q Quadrature Error (deg)
Returns the mean I/Q quadrature error (phase imbalance) of the received signal. This value is expressed in degrees.
QEVM:Results:Mean Magnitude Error (%)
Returns the mean averaged magnitude error of the received signal. This value is expressed as a percentage.
QEVM:Results:Mean Peak EVM (%)
Returns the mean averaged peak EVM of the received signal. This value is expressed as a percentage.
QEVM:Results:Mean Phase Error (deg)
Returns the mean averaged phase error of the received signal. This value is expressed in degrees.
QEVM:Results:Mean RMS EVM (%)
Returns the mean averaged RMS EVM of the received signal. This value is expressed as a percentage.
QEVM:Spectrum Inverted
Specifies whether the spectrum of the signal is inverted.
Radio Configuration
Specifies the radio configuration for the channel.
Reference Level
Specifies the reference level, which represents the maximum expected power of the RF input signal. This value is expressed in dBm for RF devices and Vpk-pk for baseband devices.
Reference Level Headroom
Specifies the margin RFmx adds to the Reference Level property. The margin avoids clipping and overflow warnings if the input signal exceeds the configured reference level.
Result Fetch Timeout (s)
Specifies the time to wait before results are available in the RFmxCDMA2k Property Node. This value is expressed in seconds.
SEM:All Traces Enabled
Specifies whether to enable the traces to be stored and retrieved after performing the SEM measurement.
SEM:Averaging:Count
Specifies the number of acquisitions used for averaging when you set the SEM Averaging Enabled property to True.
SEM:Averaging:Enabled
Specifies whether to enable averaging for the SEM measurement.
SEM:Averaging:Type
Specifies the averaging type for averaging multiple spectrum acquisitions. The averaged spectrum is used for the SEM measurement.
SEM:Carrier:Integration Bandwidth (Hz)
Returns the SEM carrier integration bandwidth. This value is expressed in Hz.
SEM:Measurement Enabled
Specifies whether to enable the SEM measurement.
SEM:Number of Analysis Threads
Specifies the maximum number of threads used for parallelism for the SEM measurement.
SEM:Offset:Bandwidth Integral
Returns the bandwidth integral for a specific offset segment.
SEM:Offset:Number of Offsets
Returns the number of SEM offset segments.
SEM:Offset:RBW Filter:Bandwidth (Hz)
Returns the bandwidth of the RBW filter used to sweep the offset segment. This value is expressed in Hz.
SEM:Offset:RBW Filter:Type
Returns the type of RBW filter used to sweep the offset segment.
SEM:Offset:Start Frequency (Hz)
Returns the start frequency of an SEM offset segment relative to the carrier frequency. This value is expressed in Hz.
SEM:Offset:Stop Frequency (Hz)
Returns the stop frequency of an SEM offset segment relative to the carrier frequency. This value is expressed in Hz.
SEM:Results:Carrier:Absolute Integrated Power (dBm)
Returns the carrier power. The carrier power is the power centered at the center frequency and integrated over the carrier bandwidth of 1.23 MHz. This value is expressed in dBm.
SEM:Results:Lower Offset:Absolute Integrated Power (dBm)
Returns the absolute power measured in the lower (negative) offset segment. This value is expressed in dBm.
SEM:Results:Lower Offset:Absolute Peak Power (dBm)
Returns the peak power measured in the lower (negative) offset segment. This value is expressed in dBm.
SEM:Results:Lower Offset:Margin (dB)
Returns the margin from the limit mask value specified by the standard. This value is expressed in dB. Margin is defined as the minimum difference between the spectrum and the closest limit mask, which can be absolute or relative.
SEM:Results:Lower Offset:Margin Absolute Power (dBm)
Returns the absolute power at which the margin occurred in the lower (negative) offset segment. This value is expressed in dBm.
SEM:Results:Lower Offset:Margin Frequency (Hz)
Returns the frequency at which the margin occurred in the lower (negative) offset segment. This value is expressed in Hz.
SEM:Results:Lower Offset:Margin Relative Power (dB)
Returns the power at which the margin occurred in the lower (negative) offset segment relative to the carrier absolute integrated power. This value is expressed in dB.
SEM:Results:Lower Offset:Measurement Status
Indicates the lower offset segment measurement status based on measurement limits specified by the standard.
SEM:Results:Lower Offset:Peak Frequency (Hz)
Returns the frequency at which the peak power occurred in the lower offset segment. This value is expressed in Hz.
SEM:Results:Lower Offset:Relative Integrated Power (dB)
Returns the power measured in the lower (negative) offset segment relative to the carrier absolute integrated power. This value is expressed in dB.
SEM:Results:Lower Offset:Relative Peak Power (dB)
Returns the peak power measured in the lower (negative) offset segment relative to the carrier absolute integrated power. This value is expressed in dB.
SEM:Results:Measurement Status
Indicates the overall measurement status based on the measurement limits, which are specified by the standard for each offset segment.
SEM:Results:Upper Offset:Absolute Integrated Power (dBm)
Returns the power measured in the upper (positive) offset segment. This value is expressed in dB.
SEM:Results:Upper Offset:Absolute Peak Power (dBm)
Returns the peak power measured in the upper (positive) offset segment. This value is expressed in dBm.
SEM:Results:Upper Offset:Margin (dB)
Returns the margin from the limit mask value specified by the standard. This value is expressed in dB. Margin is defined as the minimum difference between the spectrum and the closest limit mask (absolute or relative).
SEM:Results:Upper Offset:Margin Absolute Power (dBm)
Returns the power at which the margin occurred in the upper (positive) offset segment. This value is expressed in dBm.
SEM:Results:Upper Offset:Margin Frequency (Hz)
Returns the frequency at which the margin occurred in the upper (positive) offset. This value is expressed in Hz.
SEM:Results:Upper Offset:Margin Relative Power (dB)
Returns the power at which the margin occurred in the upper (positive) offset segment. This value is expressed in dBm.
SEM:Results:Upper Offset:Measurement Status
Indicates the upper offset measurement status based on measurement limits set by the standard.
SEM:Results:Upper Offset:Peak Frequency (Hz)
Returns the frequency at which the peak power occurred in the upper offset segment. This value is expressed in Hz.
SEM:Results:Upper Offset:Relative Integrated Power (dB)
Returns the power measured in the upper (positive) offset segment relative to the carrier absolute integrated power. This value is expressed in dB.
SEM:Results:Upper Offset:Relative Peak Power (dB)
Returns the peak power measured in the upper (positive) offset segment relative to the carrier absolute integrated power. This value is expressed in dB.
SEM:Sweep Time:Auto
Specifies whether the measurement computes the sweep time.
SEM:Sweep Time:Interval (s)
Specifies the sweep time when you set the SEM Sweep Time Auto property to False. This value is expressed in seconds.
Selected Ports
Specifies the instrument port to be configured to acquire a signal. Use RFmxInstr Get Available Ports VI to get the valid port names.
Selector String
Specifies the selector strings used to access all subsequent properties in this instance of the property node.
SlotPhase:All Traces Enabled
Specifies whether to enable the traces to be stored and retrieved after performing the SlotPhase measurement.
SlotPhase:Measurement Enabled
Specifies whether to enable the SlotPhase measurement.
SlotPhase:Measurement Length (slots)
Specifies the duration of the SlotPhase measurement. This value is expressed in slots.
SlotPhase:Measurement Offset (slots)
Specifies the measurement offset to skip from the synchronization boundary. The synchronization boundary is specified by the SlotPhase Sync Mode property. This value is expressed in slots.
SlotPhase:Receive Filter Enabled
Specifies whether to enable the received filter for the SlotPhase measurement. Use this property to disable the filter, if the received signal is already filtered.
SlotPhase:Results:Maximum Phase Discontinuity (deg)
Returns the maximum slot phase discontinuity value observed in the measurement interval. This value is expressed in degrees.
SlotPhase:Spectrum Inverted
Specifies whether the spectrum of the signal is inverted.
SlotPhase:Synchronization Mode
Specifies whether the measurement is performed from the frame or slot boundary.
SlotPhase:Transient Duration (s)
Specifies the region to exclude for computing the individual slot phase discontinuity values. This value is expressed in seconds.
SlotPower:Measurement Enabled
Specifies whether to enable the SlotPower measurement.
SlotPower:Measurement Length (slots)
Specifies the duration of the SlotPower measurement. This value is expressed in slots.
SlotPower:Measurement Offset (slots)
Specifies the measurement offset to skip from the synchronization boundary. The synchronization boundary is specified by the SlotPower Sync Mode property. This value is expressed in slots.
SlotPower:Receive Filter Enabled
Specifies whether to enable the received filter for the SlotPower measurement. Use this property to disable the filter, if the received signal is already filtered.
SlotPower:Spectrum Inverted
Specifies whether the spectrum of the signal is inverted.
SlotPower:Synchronization Mode
Specifies whether the measurement is performed from the frame or slot boundary.
Spreading:Downlink:PN Offset (64 chips)
Specified the PN offset in increments of 64 chips for forward link.
Spreading:Uplink:Long Code Mask
Specifies the long code mask for reverse link spreading.
Trigger:Delay (s)
Specifies the trigger delay time. This value is expressed in seconds.
Trigger:Digital Edge:Edge
Specifies the active edge for the trigger. This property is used only when you set the Trigger Type property to Digital Edge.
Trigger:Digital Edge:Source
Specifies the source terminal for the digital edge trigger. This property is used only when you set the Trigger Type property to Digital Edge.
Trigger:IQ Power Edge:Level
Specifies the power level at which the device triggers. This value is expressed in dB when the IQ Power Edge Level Type property is set to Relative and in dBm when the IQ Power Edge Level Type property is set to Absolute. The device asserts the trigger when the signal exceeds the level specified by the value of this property, taking into consideration the specified slope. This property is used only when you set the Trigger Type property to IQ Power Edge.
Trigger:IQ Power Edge:Level Type
Specifies the reference for the IQ Power Edge Level Type property. This property is used only when you set the Trigger Type property to IQ Power Edge.
Trigger:IQ Power Edge:Slope
Specifies whether the device asserts the trigger when the signal power is rising or when it is falling. The device asserts the trigger when the signal power exceeds the specified level with the slope you specify. This property is used only when you set the Trigger Type property to IQ Power Edge.
Trigger:IQ Power Edge:Source
Specifies the channel from which the device monitors the trigger. This property is used only when you set the Trigger Type property to IQ Power Edge.
Trigger:Minimum Quiet Time:Duration (s)
Specifies the time duration for which the signal must be quiet before the signal analyzer arms the I/Q power edge trigger. This value is expressed in seconds.
Trigger:Minimum Quiet Time:Mode
Specifies whether the measurement computes the minimum quiet time used for triggering.
Trigger:Type
Specifies the trigger type.

RFmx CDMA2k LabVIEW Reference

Log in to get a better experience