Interface Adapter Module Specifications

Interface Adapter Module Specifications

These specifications apply to Vision interface adapter modules.

Revision History

Version Date changed Description
379285B-01 October 2026 Added IVN-14810 support.
379285A-01 July 2026 Initial release.

The specifications in this section are common to all Vision interface adapter modules. To access specific information, use the individual specifications links from the table of contents.

Looking For Something Else?

For information not found in the specifications for your product, such as operating instructions, browse Related Information.

Definitions

Warranted Specifications describe the performance of a model under stated operating conditions and are covered by the model warranty.

Characteristics describe values that are relevant to the use of the model under stated operating conditions but are not covered by the model warranty.

  • Typical—describes the performance met by a majority of models.
  • Nominal—describes an attribute that is based on design, conformance testing, or supplemental testing.
  • Measured—describes the measured performance of a representative model.

    • Values are Typical unless otherwise noted.

    Conditions

    Specifications are valid under the following conditions unless otherwise noted.

    • Ambient temperature of 23 °C ±5 °C
    • Installed in a chassis with a slot cooling capacity ≥58 W

    Safety Compliance Standards

    This product is designed to meet the requirements of the following electrical equipment safety standards for measurement, control, and laboratory use:

    • IEC 61010-1, EN 61010-1
    • UL 61010-1, CSA C22.2 No. 61010-1
    Note For safety certifications, refer to the product label or visit ni.com/product-certifications, search by model number, and click the appropriate link.

    Environmental Guidelines

    Notice Failure to follow the mounting instructions in the Interface Adapter Module User Manual can cause temperature derating.
    Notice Use this product indoors only.
    Notice Apply strain relief near the input connectors of all cables. Ensure the strain relief does not cause directional bias on the cable connectors within the input connectors.
    Notice Not all chassis with a slot cooling capacity of 58 W or higher can achieve the specified ambient temperature range for this product. Refer to the specifications for the PXI chassis to confirm the ambient temperature ranges your chassis can support.

    Environmental Characteristics

    Table 1. Temperature
    Parameter Value
    Operating temperature − Chassis with slot cooling capacity ≥58 W 0 °C to 55 °C
    Storage temperature −40 °C to 71 °C
    Table 2. Humidity
    Parameter Value
    Operating humidity 10% to 90% relative, non-condensing
    Storage humidity 5% to 95% relative, non-condensing
    Table 3. Pollution Degree
    Parameter Value
    Pollution Degree 2
    Table 4. Maximum Altitude
    Parameter Value
    Maximum altitude 2,000 m
    Table 5. Shock and Vibration
    Parameter Value
    Operating vibration 5 Hz to 500 Hz, 0.3 g RMS
    Non-operating vibration 5 Hz to 500 Hz, 2.4 g RMS
    Operating shock 30 g, half-sine, 11 ms pulse

    EMC Guidelines

    Follow these guidelines to ensure the specified electromagnetic compatibility (EMC) performance.

    Notice Changes or modifications to the product not expressly approved by NI could void your authority to operate the product under your local regulatory rules.
    Notice This product is not intended for use in residential environments, as it may cause interference to other electronic devices.
    Notice Operate this product only with shielded HFM (Mini-FAKRA) coaxial cables.
    Notice Use 30 m (100 ft) or shorter I/O cables.

    EMC Standards

    This product meets the requirements of the following EMC standards for electrical equipment for measurement, control, and laboratory use:

    • EN 61326-1 (IEC 61326-1): Class A emissions; Industrial immunity
    • EN 55011 (CISPR 11): Group 1, Class A emissions
    • AS/NZS CISPR 11: Group 1, Class A emissions
    • ICES-001: Class A emissions
    • KS C 9811 and KS C 9610-6-2
    Note Group 1 equipment is any industrial, scientific, or medical equipment that does not intentionally generate radio frequency energy for the treatment of material or inspection/analysis purposes.
    Note In Europe, Australia, New Zealand, and Canada (per CISPR 11) Class A equipment is intended for use in non-residential locations.

    Power Requirements

    Table 6. Power Specifications
    Parameter Value
    Voltage rating 12 V, 1.8 V
    Power rating 7.5 W, maximum