NI-TimeSync 18.1 Known Issues

Aperçu

This document contains the NI-TimeSync known issues that were discovered before and since the release of the NI-TimeSync 18.1. Not every issue known to NI will appear on this list; it is intended to only show the severe and common issues.

Known Issues by Date

The following items are known issues in Timesync 18.1 sorted by Date.

246727 Changing the priority in NI MAX or the Web-based Configuration & Monitoring Utility may leave ni-rt.ini in an inconsistent state.
477434 The Timesync Software-Based 1588 plug-in fails to synchronize properly when used with a secondary network adapter on PharLap ETS and VxWorks targets.
493251 Running an ARM-based Linux Real-Time target as a 1588 master may degrade synchronization
652137 Disabling/re-enabling primary ethernet ports in NI-MAX or in the command line will cause synchronization issues
707309 Timesync 18.1.0 installed with System Configuration 18.5 on a Linux Real-Time target can make the target inaccessible from NI-MAX



ID Known Issue
246727

Return
Changing the priority in NI MAX or the Web-based Configuration & Monitoring Utility may leave ni-rt.ini in an inconsistent state.

Workaround: N/A

Reported Version: 1.1    Resolved Version: N/A    Added: 08/03/2015
477434

Return
The Timesync Software-Based 1588 plug-in fails to synchronize properly when used with a secondary network adapter on PharLap ETS and VxWorks targets.

Workaround: National Instruments recommends that you only use the primary network adapter when using the Timesync Software-Based 1588 plug-in.

Reported Version: 14.0    Resolved Version: N/A    Added: 08/03/2015
493251

Return
Running an ARM-based Linux Real-Time target as a 1588 master may degrade synchronization.

Workaround: National Instruments recommends that you only use ARM-based targets running NI Linux Real-Time as 1588 slaves. ARM-based targets running NI Linux Real-Time are slave only by default.

Reported Version: 14.0    Resolved Version: N/A    Added: 08/03/2015
652137

Return
Disabling/re-enabling an Ethernet port on a cRIO-903x (Sync) or an IC-317x in NI-MAX or in the command line will cause synchronization issues unless the system is rebooted. Issues might appear as undefined static time offsets, asynchronous FPGA times or the Time Source I/O reporting “None”. Never disable eth0 on the cRIO-9035x (Sync) or eth1 on IC-317x, this will cause all synchronization to halt.

Workaround: N/A

Reported Version: 17.0    Resolved Version: N/A    Added: 07/07/2017
707309

Return

Installing a custom installation on a Linux Real-Time target which includes System Configuration 18.5.0 and Timesync 18.1.0 or Timesync 18.0.0 will cause the target to become unreachable by NI MAX and the System Configuration API. If SSH, WIF, WebDAV, or FTP access were enabled prior to the target becoming unreachable, they will still be usable.

Workaround: This issue is resolved in Timesync 18.1.1. If a target has entered an unreachable state, it can be recovered by restarting the target in safe mode and reformatting it from NI MAX. 

Reported Version: 18.1.0    Resolved Version: 18.1.1    Added: 10/29/2018

Document last updated on 06/18/2018

Glossary of Terms

 

  • Bug ID - When an issue is reported to NI, you may be given this ID or find it on ni.com.  You may also find IDs posted by NI on the discussion forums or in KnowledgeBase articles.
  • Legacy ID – An older issue ID that refers to the same issue.  You may instead find this issue ID in older known issues documents.
  • Description - A few sentences which describe the problem. The brief description given does not necessarily describe the problem in full detail.
  • Workaround - Possible ways to work around the problem.
  • Reported Version - The earliest version in which the issue was reported.
  • Resolved Version - Version in which the issue was resolved or was no longer applicable. "N/A" indicates that the issue has not been resolved.
  • Date Added - The date the issue was added to the document (not the reported date).