NationalInstruments.RFmx.SpecAnMX

Defines a root class which is used to identify and control SpecAn signal configuration.

Represents an ACP measurement.

Provides methods to configure the ACP measurement.

Provides methods to fetch and read the ACP measurement results.

Represents an AMPM measurement.

Provides methods to configure the AMPM measurement.

Provides methods to fetch and read the AMPM measurement results.

Represents the CCDF measurement.

Provides methods to configure the CCDF measurement.

Provides methods to fetch and read the CCDF measurement results.

Represents the CHP measurement.

Provides methods to configure the channel power (CHP) measurement.

Provides methods to fetch and read the channel power (CHP) measurement results.

Specifies constants for I/O terminals.

Represents a DPD measurement.

Provides methods to apply DPD measurements.

Provides methods to configure the DPD measurement.

Provides methods to Pre DPD measurements.

Provides methods to fetch and read the DPD measurement results.

Represents a frequency count (Fcnt) measurement.

Provides methods to configure the frequency count (Fcnt) measurement.

Provides methods to fetch and read the frequency count (Fcnt) measurement results.

Represents a Harmonics measurement.

Provides methods to configure the Harmonics measurement.

Provides methods to fetch and read the Harmonics measurement results.

Represents the IM measurement.

Provides methods to configure the IM measurement.

Provides methods to fetch and read the IM measurement results.

Represents an I/Q measurement.

Provides methods to configure the I/Q measurement.

Provides methods to fetch the I/Q measurement results.

Represents the IDPD measurement.

Provides methods to configure the IDPD measurement.

Provides methods to fetch and read the IDPD measurement results.

Defines a root class which is used to identify and control SpecAn list.

Represents a Marker measurement.

Provides methods to configure the Marker measurement.

Provides methods to fetch and read the Marker measurement results.

Represents the NF measurement.

Provides methods to configure the NF measurement.

Provides methods to fetch and read the NF measurement results.

Represents an OBW measurement.

Provides methods to configure the occupied bandwidth (OBW) measurement.

Provides methods to fetch and read the occupied bandwidth (OBW) measurement results.

Represents the PAVT measurement.

Provides methods to configure the PAVT measurement.

Provides methods to fetch and read the PAVT measurement results.

Represents the PhaseNoise measurement.

Provides methods to configure the PhaseNoise measurement.

Provides methods to fetch and read the PhaseNoise measurement results.

Represents the PowerList measurement.

Provides methods to configure the PowerList measurement.

Provides methods to fetch and read the PowerList measurement results.

Represents a spectral emission mask (SEM) measurement.

Provides methods to configure the SEM measurement.

Provides methods to fetch and read the spectral emission mask (SEM) measurement results.

Represents a Spectrum measurement.

Provides methods to configure the Spectrum measurement.

Provides methods to fetch and read the Spectrum measurement results.

Represents a Spur measurement.

Provides methods to configure the spurious emission (Spur) measurement.

Provides methods to fetch and read the spurious emission (Spur) measurement results.

Represents members that are common to all sub-object of RFmxSpecAnMX classes.

Represents a transmit power (TXP) measurement.

Provides methods to configure the transmit power (TXP) measurement.

Provides methods to fetch and read the transmit power (TXP) measurement results.

Specifies whether the amplitude of the frequency bins, used in the measurement, is corrected for external attenuation at the RF center frequency, or at the individual frequency bins. Use the _RFmxInstrCfgExternalAttenuationTable function to configure the external attenuation table.

Specifies whether to enable averaging for the adjacent channel power (ACP) measurement.

Specifies the averaging type for averaging multiple spectrum acquisitions. The averaged spectrum is used for adjacent channel power (ACP) measurement.

Specifies whether to consider the carrier power as part of the total carrier power measurement.

Specifies whether to apply the root-raised-cosine (RRC) filter on the acquired carrier channel before measuring the carrier channel power.

Specifies the type of detector to be used.

Specifies the overlap mode when you set the SetMeasurementMethod(string, RFmxSpecAnMXAcpMeasurementMethod) method to SequentialFft.

Specifies the FFT window type to use to reduce spectral leakage.

Specifies whether the measurement computes an IF output power level offset for the offset channels to improve the dynamic range of the ACP measurement.

Specifies the method for performing the adjacent channel power (ACP) measurement.

Specifies whether the measurement calibrates the noise floor of analyzer or performs the ACP measurement. Refer to the measurement guidelines section in the Noise Compensation Algorithm topic for more information.

Specifies whether RFmx automatically computes the averaging count used for instrument noise calibration.

Indicates whether calibration data is valid for the configuration specified by the signal name in the selectorstring parameter.

Specifies whether the noise calibration and measurement is performed manually by the user or automatically by RFmx. Refer to the measurement guidelines section in the Noise Compensation Algorithm topic for more information.

Specifies whether to enable compensation of the channel powers for the inherent noise floor of the signal analyzer.

Specifies the noise compensation type. Refer to the Noise Compensation Algorithm topic for more information.

Specifies whether to enable the offset channel for adjacent channel power (ACP) measurement.

Specifies the offset frequency definition used to specify the SetOffsetFrequency(string, double) method.

Specifies the carrier to be used as power reference to measure the offset channel relative power. The offset channel power is measured only if you set the SetOffsetPowerReferenceCarrier(string, RFmxSpecAnMXAcpOffsetPowerReferenceCarrier) method to Active.

Specifies whether to apply the root-raised-cosine (RRC) filter on the acquired offset channel before measuring the offset channel power.

Specifies whether the offset channel is present on one side, or on both sides of the carriers.

Specifies the units for the absolute power.

Specifies whether the measurement computes the resolution bandwidth (RBW).

Specifies the bandwidth definition which you use to specify the value of the SetRbwFilterBandwidth(string, double) method.

Specifies the shape of the digital resolution bandwidth (RBW) filter.

Specifies whether the measurement computes the sweep time.

Specifies the polynomial approximation cost-function of the device under test AM-to-AM characteristic.

Specifies whether to enable the results that rely on the AM to AM characteristics.

Specifies the polynomial approximation cost-function of the device under test AM-to-PM characteristic.

Specifies whether to enable the results that rely on AM to PM characteristics.

Specifies if auto detection of carrier offset and carrier bandwidth is enabled.

Specifies whether to enable averaging for the AMPM measurement.

Configures the compression point computataion.

Specifies the gain reference for compression point calculation.

Specifies whether the measurement equalizes the channel.

Specifies whether to enable the GetMeanRmsEvm(string, out double) method.

Specifies whether to enable frequency offset correction for the measurement.

Specifies whether to enable the IQ origin offset correction for the measurement.

Specifies whether the acquisition sample rate is based on the reference waveform.

Specifies the reference power used for AM to AM and AM to PM traces.

Specifies whether the reference waveform contains an idle duration.

Specifies whether the reference waveform is a modulated signal or tones.

Specifies the method used for synchronization of acquired waveform with reference waveform.

Specifies whether to enable thresholding for the acquired samples to be used for the AMPM measurement.

Specifies the reference for the power level used for thresholding.

Specifies the shape of the digital resolution bandwidth (RBW) filter.

Specifies whether to enable thresholding of the acquired samples to be used for the complementary cumulative distribution function (CCDF) measurement.

Specifies the reference for the power level used for thresholding.

Specifies whether the amplitude of the frequency bins, used in the measurement, is corrected for external attenuation at the RF center frequency, or at the individual frequency bins. Use the _RFmxInstrCfgExternalAttenuationTable function to configure the external attenuation table.

Specifies whether to enable averaging for the channel power (CHP) measurement.

Specifies the averaging type for averaging multiple spectrum acquisitions.

Specifies whether to apply the root-raised-cosine (RRC) filter on the acquired channel after measuring the channel power.

Specifies the type of detector to be used.

Specifies the FFT window type used to reduce spectral leakage.

Specifies whether the measurement calibrates the noise floor of analyzer or performs the CHP measurement. Refer to the measurement guidelines section in the Noise Compensation Algorithm topic for more information.

Specifies whether RFmx automatically computes the averaging count used for instrument noise calibration.

Indicates whether calibration data is valid for the configuration specified by the signal name in the selectorstring parameter.

Specifies whether the noise calibration and measurement is performed manually by the user or automatically by RFmx. Refer to the measurement guidelines section in the Noise Compensation Algorithm topic for more information.

Specifies whether RFmx compensates for the instrument noise when performing the measurement. To compensate for instrument noise when performing a CHP measurement, set the SetNoiseCalibrationMode(string, RFmxSpecAnMXChpNoiseCalibrationMode) method to Auto, or set the CHP Noise Cal Mode method to Manual and SetMeasurementMode(string, RFmxSpecAnMXChpMeasurementMode) method to Measure. Refer to the measurement guidelines section in the Noise Compensation Algorithm topic for more information.

Specifies the noise compensation type. Refer to the Noise Compensation Algorithm topic for more information.

Specifies whether the measurement computes the resolution bandwidth (RBW).

Specifies whether the measurement computes the resolution bandwidth (RBW).

Specifies the shape of the digital resolution bandwidth (RBW) filter.

Specifies whether to apply the root-raised-cosine (RRC) filter on the acquired channel after measuring the channel power.

Specifies whether the measurement computes the sweep time.

Specifies the active edge for the trigger. This enum is used only when you set the SetTriggerType(string, RFmxSpecAnMXTriggerType) method to DigitalEdge.

Specifies whether to enable the crest factor reduction (CFR) on the pre-distorted waveform.

Specifies the method used to perform the crest factor reduction (CFR) when you set the DpdApplyDpdCfrEnabled method to True.

Specifies the target PAPR type when you set the DpdApplyDpdCfrEnabled method to True.

Specifies the window type to be used when you set the DpdApplyDpdCfrEnabled method to True and the DpdApplyDpdCfrMethod method to PeakWindowing.

Specifies whether to use the configuration used by the DPD measurement for applying DPD.

Specifies whether to compute and apply the headroom of the predistorted waveform or to apply the value specified by GetHeadroom(string, out double) on the predistorted waveform.

Specifies whether the waveform contains an idle duration.

Specifies the predistortion type when you set the SetModel(string, RFmxSpecAnMXDpdModel) method to LookupTable.

Specifies the predistortion type when you set the SetModel(string, RFmxSpecAnMXDpdModel) method to MemoryPolynomial or GeneralizedMemoryPolynomial.

Specifies the DPD model for applying DPD when you set the SetConfigurationInput(string, RFmxSpecAnMXDpdApplyDpdConfigurationInput) method to User.

Specifies the DPD Lookup Table (LUT) type when you set the DpdApplyDpdConfigurationInput method toUser.

Specifies if auto detection of carrier offset and carrier bandwidth is enabled.

Specifies whether to enable averaging for the DPD measurement.

Specifies whether to enable frequency offset correction for the DPD measurement.

Specifies whether to enable the IQ origin offset correction for the measurement.

Specifies whether to enable iterative computation of the DPD Results DPD Polynomial using indirect-learning architecture.

Specifies the polynomial approximation cost-function of the device under test AM-to-AM characteristic when you set the SetModel(string, RFmxSpecAnMXDpdModel) method to LookupTable.

Specifies the polynomial approximation cost-function of the device under test AM-to-PM characteristic when you set the SetModel(string, RFmxSpecAnMXDpdModel) method to LookupTable.

Specifies whether to enable thresholding of the acquired samples to be used for the DPD measurement when you set the SetModel(string, RFmxSpecAnMXDpdModel) method to LookupTable.

Specifies the reference for the power level used for thresholding.

Specifies the type of the DPD lookup table (LUT).

Specifies if the training waveform required for the extraction of the DPD model coefficients is acquired from the hardware or is configured by the user.

Specifies the acquisition sample rate configuration mode.

Configures the type of terms of the lag order DPD polynomial when you set the RFmxSpecAnMXDpdModel to GeneralizedMemoryPolynomial.

Configures the type of terms of the lead order DPD polynomial when you set the RFmxSpecAnMXDpdModel to GeneralizedMemoryPolynomial.

Configures the type of terms of the DPD polynomial when you set the RFmxSpecAnMXDpdModel to MemoryPolynomial or GeneralizedMemoryPolynomial.

Specifies the DPD model used by the DPD measurement.

Specifies whether to enable the normalized mean-squared error (NMSE) computation.

Specifies whether to enable the crest factor reduction (CFR) when applying pre-DPD signal conditioning.

Specifies whether to enable the filtering operation when you set the DpdApplyDpdCfrEnabled method to True. Refer to DPD concept topic for more information about filtering.

Specifies the method used to perform crest factor reduction (CFR) when you set the DpdPreDpdCfrEnabled method to True. Refer to DPD concept topic for more information about CFR methods.

Specifies the window type to be used when you set the DpdPreDpdCfrEnabled method to True and the DpdPreDpdCfrMethod method to PeakWindowing.

Specifies whether the reference waveform contains an idle duration.

Specifies whether the reference waveform is a modulated signal or a combination of one or more sinusoidal signals.

Specifies the method used for synchronization of the acquired waveform with the reference waveform.

Specifies the gain expected from the DUT after applying DPD on the input waveform.

Specifies whether to enable averaging for the frequency count (Fcnt) measurement.

Specifies the averaging type for the frequency count (Fcnt) measurement. The averaged instantaneous signal phase difference is used for the measurement.

Specifies the shape of the digital resolution bandwidth (RBW) filter.

Specifies whether to enable thresholding of the acquired samples to be used for the frequency count (Fcnt) measurement.

Specifies the reference for the power level used for thresholding.

Specifies whether to enable a particular harmonic for measurement. Only the enabled harmonics are used to measure the total harmonic distortion (THD). This enum is not used if you set the SetAutoSetupEnabled(string, RFmxSpecAnMXHarmAutoHarmonicsSetupEnabled) method to True.

Specifies whether to enable averaging for the Harmonics measurement.

Specifies the averaging type for the Harmonics measurement. The averaged power trace is used for the measurement.

Specifies whether to enable a particular harmonic for measurement. Only the enabled Harmonics are used to measure the total harmonic distortion (THD). This enum is not used if you set the SetAutoSetupEnabled(string, RFmxSpecAnMXHarmAutoHarmonicsSetupEnabled) to True.

Specifies the method used to perform the harmonics measurement.

Specifies whether to enable compensation of the average harmonic powers for inherent noise floor of the signal analyzer.

Specifies the shape of the digital resolution bandwidth (RBW) filter.

Specifies whether the amplitude of the frequency bins, used in the measurement, is corrected for external attenuation at the RF center frequency, or at the individual frequency bins. Use the _RFmxInstrCfgExternalAttenuationTable function to configure the external attenuation table.

Specifies whether the measurement computes the intermod frequencies or uses user-specified frequencies.

Specifies whether to enable averaging for the IM measurement.

Specifies the averaging type for averaging multiple spectrum acquisitions. The averaged spectrum is used for the IM measurement.

Specifies the FFT window type to use to reduce spectral leakage.

Specifies whether the tones and intermod frequencies are relative to the RF center frequency, or are absolute frequencies.

Specifies whether the measurement computes an IF output power level offset for the intermods to maximize the dynamic range of the signal analyzer. This method is used only if you set the SetMeasurementMethod(string, RFmxSpecAnMXIMMeasurementMethod) method to DynamicRange.

Specifies whether to enable an intermod for the IM measurement. This method is not used when you set the NationalInstruments.RFmx.SpecAnMX.RFmxSpecAnMXIMConfiguration.GetAutoIntermodsSetupEnabled(string,NationalInstruments.RFmx.SpecAnMX.RFmxSpecAnMXIMAutoIntermodsSetupEnabled@) method to True.

Specifies whether to measure intermodulation products corresponding to both lower and upper intermod frequencies or either one of them. This method is not used when you set the NationalInstruments.RFmx.SpecAnMX.RFmxSpecAnMXIMConfiguration.GetAutoIntermodsSetupEnabled(string,NationalInstruments.RFmx.SpecAnMX.RFmxSpecAnMXIMAutoIntermodsSetupEnabled@) method to True.

Specifies whether to enable a local peak search around the tone or intermod frequencies to account for small frequency offsets.

Specifies the method used to perform the IM measurement.

Specifies whether the measurement computes the RBW.

Specifies the response of the digital RBW filter.

Specifies whether the measurement computes the sweep time.

Specifies whether the measurement computes the minimum acquisition bandwidth.

Specifies whether the measurement deletes the fetched record.

Specifies the mode for performing the IQ measurement.

Specifies the reference for the RFmx.SpecAnMX.RFmxSpecAnMX.SetIQPowerEdgeTriggerLevel method.

Specifies whether the device asserts the trigger when the signal power is rising or when it is falling. The device asserts the trigger when the signal power exceeds the specified level with the slope you specify. This enum is used only when you set the Trigger Type to IQPowerEdge.

Specifies whether to enable averaging for the IDPD measurement.

Specifies whether to enable equalization.

Specifies whether to enable EVM computation.

Specifies the units of the EVM results.

Specifies acquisition sample rate configuration mode.

Specifies whether the reference waveform contains idle duration or dead time.

Specifies the type of reference waveform.

Specifies the set of properties that are considered by RFmx in the locked signal configuration state.

specifies the function type for the selected marker. The default value is Off.

Moves the marker to the next highest, next left, or next right peak above the threshold on the configured trace.

Specifies whether to enable the peak excursion check for the trace while finding the peaks.

Specifies whether to enable the threshold for the trace while finding the peaks.

Configures the measurement trace to be used by the marker.

Configures the marker type.

Specifies the type of measurement.

Specifies whether to enable averaging for the noise figure (NF) measurement.

Returns whether the calibration data is valid for the configuration specified by the signal name in the selectorString parameter.

Specifies whether the noise figure (NF) measurement accounts for the ohmic losses between the noise source and input port of the analyzer during the calibration step, excluding any losses which you have specified using the SetYFactorNoiseSourceLoss(string, double[]) method.

Specifies whether the measurement should calibrate the noise characteristics of the analyzer or compute the noise characteristics of the DUT for the cold source method.

Specifies whether the noise figure (NF) measurement accounts for ohmic losses between the noise source and the input port of the DUT, excluding the losses that are common to calibration and the measurement steps for the Y-Factor method, which are specified by the SetYFactorNoiseSourceLoss(string, double[]) method.

Specifies whether the noise figure (NF) measurement accounts for ohmic losses between the output port of the DUT and the input port of the analyzer.

Specifies the type of DUT.

Specifies whether an external preamplifier is present in the signal path.

Specifies the context of the NF Frequency List method.

Specifies the sideband when you set the SetDutType(string, RFmxSpecAnMXNFDutType) method to either Downconverter or Upconverter, and the SetFrequencyConverterFrequencyContext(string, RFmxSpecAnMXNFFrequencyConverterFrequencyContext) method to IF.

Specifies the measurement method used to perform the noise figure (NF) measurement.

Specifies whether the measurement should calibrate the noise characteristics of the analyzer or compute the noise characteristics of the DUT when you set the SetMeasurementMethod(string, RFmxSpecAnMXNFMeasurementMethod) method to YFactor.

Specifies whether the noise figure (NF) measurement should account for ohmic losses inherent to the noise source used in the Y-Factor method common to the calibration and measurement steps.

Specifies whether the measurement should calibrate the noise characteristics of the analyzer or compute the noise characteristics of the DUT when you set the SetMeasurementMethod(string, RFmxSpecAnMXNFMeasurementMethod) method to YFactor.

Specifies whether the amplitude of the frequency bins, used in the measurement, is corrected for external attenuation at the RF center frequency, or at the individual frequency bins. Use the _RFmxInstrCfgExternalAttenuationTable function to configure the external attenuation table.

Specifies whether to enable averaging for the occupied bandwidth (OBW) measurement.

Specifies the averaging type for averaging multiple spectrum acquisitions. The averaged spectrum is used for occupied bandwidth (OBW) measurement.

Specifies the FFT window type to use to reduce spectral leakage.

Specifies the units for the absolute power.

Specifies whether the measurement computes the resolution bandwidth (RBW).

Specifies the bandwidth definition which you use to specify the value of the SetRbwFilterBandwidth(string, double) method.

Specifies the shape of the digital resolution bandwidth (RBW) filter.

Specifies whether the measurement computes the sweep time.

Specifies whether to enable frequency offset correction for the measurement.

Specifies whether to enable frequency offset correction per segment for the measurement. While you set this property to True, ensure that the PavtFrequencyOffsetCorrectionEnabled attribute is set to True and the PavtSegmentType attribute is set to PhaseAndAmplitude.

Specifies the mode of configuring the measurement interval.

Specifies the location at which the segment is measured.

Specifies whether the phase measurement results are unwrapped or wrapped.

Specifies the type of segment.

Specifies whether to enable or disable the phase noise cancellation. Refer to the Phase Noise topic for more information on phase noise cancellation.

Specifies the FFT window to use.

Specifies the frequency range for integrated noise measurements.

Specifies how the measurement computes offset subranges.

Specifies the smoothing type used to smoothen the log plot trace.

Specifies whether to remove spurs from the log plot trace.

Specifies all the attribute identifiers.

Specifies whether the amplitude of the frequency bins, used in the measurement, is corrected for external attenuation at the RF center frequency, or at the individual frequency bins. Use the _RFmxInstrCfgExternalAttenuationTable function to configure the external attenuation table.

Specifies whether to enable averaging for the spectral emission mask (SEM) measurement.

Specifies the averaging type for averaging multiple spectrum acquisitions. The averaged spectrum is used for spectral emission mask (SEM) measurement.

Specifies whether to consider the carrier power as part of the total carrier power measurement.

Specifies whether the measurement computes the resolution bandwidth (RBW) of the carrier.

Specifies the bandwidth definition which you use to specify the value of the SetCarrierRbwFilterBandwidth(string, double) method.

Specifies the shape of the digital resolution bandwidth (RBW) filter.

Specifies whether to apply the root-raised-cosine (RRC) filter on the acquired carrier channel before measuring the carrier channel power.

Indicates the overall measurement status based on the measurement limits and the fail criteria that you set in the SetOffsetLimitFailMask(string, RFmxSpecAnMXSemOffsetLimitFailMask) method for each offset segment.

Specifies the FFT window type to use to reduce spectral leakage.

Indicates the lower offset segment measurement status based on measurement limits and the fail criteria that you specify in the SetOffsetLimitFailMask(string, RFmxSpecAnMXSemOffsetLimitFailMask) method.

Specifies whether the absolute limit mask is a flat line or a line with a slope.

Specifies whether to enable the offset segment for spectral emission mask (SEM) measurement.

Specifies the definition of the start frequency and stop frequency of the offset segments from the nearest carrier channels.

Specifies the criteria to determine the measurement fail status.

Specifies whether the measurement computes the resolution bandwidth (RBW).

Specifies whether the measurement computes the resolution bandwidth (RBW).

Specifies the shape of the digital resolution bandwidth (RBW) filter.

Specifies whether the relative limit mask is a flat line or a line with a slope.

Specifies whether the offset segment is present on one side, or on both sides of the carrier.

Specifies the units for the absolute power.

Specifies whether the power reference is the integrated power or the peak power in the closest carrier channel. The leftmost carrier is the carrier closest to all the lower (negative) offset segments. The rightmost carrier is the carrier closest to all the upper (positive) offset segments.

Specifies whether the measurement computes the sweep time.

Indicates the upper offset measurement status based on measurement limits and the fail criteria that you specify in the SetOffsetLimitFailMask(string, RFmxSpecAnMXSemOffsetLimitFailMask) method.

Specifies whether the amplitude of the frequency bins, used in the measurement, is corrected for external attenuation at the RF center frequency, or at the individual frequency bins. Use the _RFmxInstrCfgExternalAttenuationTable function to configure the external attenuation table.

Specifies whether to analyze just the real I or Q component of the acquired IQ data, or analyze the complex IQ data.

Specifies whether to enable averaging for the spectrum measurement.

Specifies the averaging type for averaging multiple spectrum acquisitions. The averaged spectrum is used for spectrum measurement.

Specifies the type of detector to be used.

Specifies the overlap mode when you set the SpectrumMeasurementMethod method to SequentialFft.

Specifies the overlap type when you set the SpectrumMeasurementMethod method to SequentialFft.

Specifies the FFT window type to use to reduce spectral leakage.

Specifies the method for performing the Spectrum measurement.

Specifies whether the measurement calibrates the noise floor of analyzer or performs the spectrum measurement. Refer to the measurement guidelines section in the Noise Compensation Algorithm topic for more information.

Specifies whether RFmx automatically computes the averaging count used for instrument noise calibration.

Indicates whether calibration data is valid for the configuration specified by the signal name in the selectorstring parameter.

Specifies whether the noise calibration and measurement is performed manually by the user or automatically by RFmx. Refer to the measurement guidelines section in the Noise Compensation Algorithm topic for more information.

Specifies whether to enable compensation of the spectrum for the inherent noise floor of the signal analyzer.

Specifies the noise compensation type. Refer to the Noise Compensation Algorithm topic for more information.

You do not need to use a selector string to configure or read this for default signal instance.

Specifies whether the measurement computes the resolution bandwidth (RBW).

Specifies the bandwidth definition which you use to specify the value of the SetRbwFilterBandwidth(string, double) method.

Specifies the shape of the digital resolution bandwidth (RBW) filter.

Specifies whether the measurement computes the sweep time.

Specifies whether the video bandwidth (VBW) is expressed directly or computed based on the VBW to RBW ratio.

Specifies whether the absolute limit threshold is a flat line or a line with a slope.

Specifies whether the amplitude of the frequency bins, used in the measurement, is corrected for external attenuation at the RF center frequency, or at the individual frequency bins. Use the _RFmxInstrCfgExternalAttenuationTable function to configure the external attenuation table.

Specifies whether to enable averaging for the spurious emission (Spur) measurement.

Specifies the averaging type for averaging multiple spectrum acquisitions. The averaged spectrum is used for the measurement. Refer to the Averaging section of the Spectrum topic for more information about averaging types.

Specifies the FFT window type to use to reduce spectral leakage. Refer to the Window and FFT section of the Spectrum topic for more information about FFT window types.

Indicates the overall measurement status.

Specifies the type of detector to be used. Use "range(n)" as the selector string to configure or read this method.

Specifies whether to measure the spurious emissions (Spur) in the frequency range.

Indicates the measurement status for the frequency range.

Specifies whether the video bandwidth (VBW) is expressed directly or computed based on the VBW to RBW ratio.

Specifies whether the measurement computes the resolution bandwidth (RBW).

Specifies whether the measurement computes the resolution bandwidth (RBW).

Specifies the shape of the digital resolution bandwidth (RBW) filter.

Specifies whether the measurement computes the sweep time.

Specifies whether the measurement computes the minimum quiet time used for triggering.

Specifies the trigger type.

Specifies whether to enable averaging for the measurement.

Specifies the averaging type for averaging the power over multiple acquisitions. The averaged power trace is used for the measurement. Refer to the Averaging section of the Spectrum topic for more information about averaging types.

Specifies the shape of the digital RBW filter.

Specifies whether to enable thresholding of the acquired samples to be used for the measurement.

Specifies the reference for the power level used for thresholding.

Specifies whether the video bandwidth (VBW) is expressed directly or computed based on the VBW to RBW ratio.