Use the RFmxBluetooth properties to access options for configuring and fetching measurements.

© 2019–2025 National Instruments Corporation. All rights reserved.

20dBBandwidth:All Traces Enabled
Specifies whether to enable all the traces for the 20dBBandwidth measurement.
20dBBandwidth:Averaging:Count
Specifies the number of acquisitions used for averaging when you set the 20dBBandwidth Averaging Enabled property to True.
20dBBandwidth:Averaging:Enabled
Specifies whether to enable averaging for the 20dBBandwidth measurement.
20dBBandwidth:Measurement Enabled
Specifies whether to enable the 20dBBandwidth measurement specified in section 4.5.5 of the Bluetooth Test Specification RF.TS.p33. The measurement uses a span of 3 MHz internally. This measurement is valid only for basic rate (BR) packets.
20dBBandwidth:Number of Analysis Threads
Specifies the maximum number of threads used for parallelism for the 20dB bandwidth measurement.
20dBBandwidth:Results:Bandwidth (Hz)
Returns the 20dB bandwidth of the received signal. It is computed as the difference between 20dBBandwidth Results High Freq and 20dBBandwidth Results Low Freq. This value is expressed in Hz.
20dBBandwidth:Results:High Frequency (Hz)
Returns the highest frequency above the center frequency at which the transmit power drops 20 dB below the peak power. This value is expressed in Hz.
20dBBandwidth:Results:Low Frequency (Hz)
Returns the lowest frequency below the center frequency at which the transmit power drops 20 dB below the peak power. This value is expressed in Hz.
20dBBandwidth:Results:Peak Power (dBm)
Returns the peak power of the measured spectrum. This value is expressed in dBm.
ACP:All Traces Enabled
Specifies whether to enable all traces for the adjacent channel power (ACP) measurements.
ACP:Averaging:Count
Specifies the number of acquisitions used for averaging when you set the ACP Averaging Enabled property to True.
ACP:Averaging:Enabled
Specifies whether to enable averaging for the ACP measurement.
ACP:Burst Synchronization Type
Specifies the type of synchronization used for detecting the start of the EDR packet in the adjacent channel power (ACP) measurement.
ACP:Measurement Enabled
Specifies whether to enable the ACP measurement.
ACP:Number of Analysis Threads
Specifies the maximum number of threads used for parallelism for adjacent channel power (ACP) measurement.
ACP:Number of Offsets
Specifies the number of offset channels used on either side of the reference channel for the adjacent channel power (ACP) measurement when you set the ACP Offset Channel Mode property to Symmetric. This property also returns the actual number of offsets used in the ACP measurement when you set the ACP Offset Channel Mode property to In-band.
ACP:Offset Channel Mode
Specifies which offset channels are used for the measurement.
ACP:Offset Frequency (Hz)
Returns the frequency of the offset channel with respect to the reference channel frequency. This value is expressed in Hz.
ACP:Reference Channel Bandwidth
ACP:Reference Channel Bandwidth Mode
ACP:Results:Lower Offset:Absolute Power (dBm)
Returns the absolute power measured in the lower offset channel. This value is expressed in dBm.
ACP:Results:Lower Offset:Margin (dB)
Returns the margin from the limit specified by the mask with exception for lower offsets. This value is expressed in dB. Margin is defined as the difference between the offset absolute power and mask with exception. This result is valid only if you set the ACP Offset Channel Mode property to In-band. This property returns NaN if you set the ACP Offset Channel Mode property to Symmetric.
ACP:Results:Lower Offset:Relative Power (dB)
Returns the relative power in the lower offset channel measured with respect to the reference channel power. This value is expressed in dB.
ACP:Results:Measurement Status
Indicates the overall measurement status based on the measurement limits specified by the standard when you set the ACP Offset Channel Mode property to In-band.
ACP:Results:Reference Channel Power (dBm)
Returns the measured power of the reference channel. This value is expressed in dBm.
ACP:Results:Upper Offset:Absolute Power (dBm)
Returns the absolute power measured in the upper offset channel. This value is expressed in dBm.
ACP:Results:Upper Offset:Margin (dB)
Returns the margin from the limit specified by the mask with exception for upper offsets. This value is expressed in dB. Margin is defined as the difference between the offset absolute power and mask with exception. This result is valid only if you set the ACP Offset Channel Mode property to In-band. This property returns NaN if you set the ACP Offset Channel Mode property to Symmetric.
ACP:Results:Upper Offset:Relative Power (dB)
Returns the relative power in the upper offset channel measured with respect to the reference channel power. This value is expressed in dB.
Advanced:Auto Level Initial Reference Level (dBm)
Specifies the initial reference level which the RFmxBT Auto Level VI uses to estimate the peak power of the input signal. This value is expressed in dBm.
Advanced:Limited Configuration Change
Specifies the set of properties that are considered by RFmx in the locked signal configuration state.
Auto Detect Signal:Detected Data Rate
Returns the data rate detected by the RFmxBT Auto Detect Signal VI. This property returns a valid data rate only if the Detected Packet Type property returns LE. This property can be queried only after calling the RFmxBT Auto Detect Signal VI.
Auto Detect Signal:Detected Packet Type
Returns the packet type detected by the RFmxBT Auto Detect Signal VI. This property can be queried only after calling the RFmxBT Auto Detect Signal VI.
Auto Detect Signal:Detected Payload Length
Returns the payload length detected by the RFmxBT Auto Detect Signal VI. This property can be queried only after calling the RFmxBT Auto Detect Signal VI.
Center Frequency (Hz)
Specifies the expected carrier frequency of the RF signal that needs to be acquired. This value is expressed in Hz. The signal analyzer tunes to this frequency.
Channel Number
Specifies the RF channel number of the signal generated by the device under test (DUT), as defined in the bluetooth specification. This property is applicable when you enable the ACP measurement and when you set the ACP Offset Channel Mode property to In-band.
External Attenuation (dB)
Specifies the attenuation of a switch (or cable) connected to the RF IN connector of the signal analyzer. This value is expressed in dB.
FrequencyRange:All Traces Enabled
Specifies whether to enable all the traces for FrequencyRange measurement.
FrequencyRange:Averaging:Count
Specifies the number of acquisitions used for averaging when you set the FrequencyRange Averaging Enabled property to True.
FrequencyRange:Averaging:Enabled
Specifies whether to enable averaging for the FrequencyRange measurement.
FrequencyRange:Measurement Enabled
Specifies whether to enable the FrequencyRange measurement specified in the section 4.5.4 of the Bluetooth Test Specification RF.TS.p33. This measurement is valid only for basic rate (BR) packets.
FrequencyRange:Number of Analysis Threads
Specifies the maximum number of threads used for parallelism for the frequency range measurement.
FrequencyRange:Results:High Frequency (Hz)
Returns the highest frequency above the center frequency at which the transmit power drops below -30 dBm measured in a 100 kHz bandwidth. This value is expressed in Hz.
FrequencyRange:Results:Low Frequency (Hz)
Returns the lowest frequency below the center frequency at which the transmit power drops below -30 dBm measured in a 100 kHz bandwidth. This value is expressed in Hz.
FrequencyRange:Span (Hz)
Specifies the span for the FrequencyRange measurement. This value is expressed in Hz. You must adjust the span according the center frequency as specified in section 4.5.4 of the Bluetooth Test Specification RF.TS.p33. It is recommended to use the span of 6 MHz for a center frequency of 2.402 GHz and 10 MHz for a center frequency of 2.48 GHz.
ModAcc:All Traces Enabled
Specifies whether to enable all the traces computed by ModAcc measurements.
ModAcc:Averaging:Count
Specifies the number of acquisitions used for averaging when you set the ModAcc Averaging Enabled property to True.
ModAcc:Averaging:Enabled
Specifies whether to enable averaging for the ModAcc measurements.
ModAcc:Burst Synchronization Type
Specifies the type of synchronization used for detecting the start of packet in ModAcc measurement.
ModAcc:EDR:I/Q Origin Offset Correction Enabled
Specifies whether to enable the I/Q origin offset correction for EDR packets. If you set this property to True, the DEVM results are computed after correcting for the I/Q origin offset.
ModAcc:Measurement Enabled
Specifies whether to enable the ModAcc measurements. You can use this property to determine the modulation quality of the bluetooth transmitter.
ModAcc:Number of Analysis Threads
Specifies the maximum number of threads used for parallelism for the ModAcc measurement. The number of threads can range from 1 to the number of physical cores. The number of threads you set may not be used in calculations. The actual number of threads used depends on the problem size, system resources, data availability, and other considerations.
ModAcc:Results:Clock Drift Mean (ppm)
Returns the clock drift estimated over the LE-CS packet. This value is expressed in ppm. When you set the ModAcc Averaging Enabled property to True, it returns the mean of the clock drift values computed for each averaging count.
ModAcc:Results:DEVM:99% DEVM (%)
Returns the 99th percentile of the differential EVM (DEVM) values computed on symbols of the EDR portion of all measured EDR packets. This value is expressed as a percentage.
ModAcc:Results:DEVM:Magnitude Error:Average RMS Magnitude Error Mean (%)
Returns the average of the RMS magnitude error values computed on each 50 us block of EDR portion of the EDR packet. When you set the ModAcc Averaging Enabled property to True, it returns the mean of the average RMS magnitude error values computed for each averaging count. This value is expressed as a percentage.
ModAcc:Results:DEVM:Magnitude Error:Peak RMS Magnitude Error Maximum (%)
Returns the peak of the RMS magnitude error values computed on each 50 us block of EDR portion of the EDR packet. When you set the ModAcc Averaging Enabled property to True, it returns the maximum of the peak RMS Magnitude error values computed for each averaging count. This value is expressed as a percentage.
ModAcc:Results:DEVM:Peak DEVM Maximum (%)
Returns the peak of the differential EVM (DEVM) values computed on symbols in the EDR portion of the EDR packet. When you set the ModAcc Averaging Enabled property to True, it returns the maximum of the peak symbol differential EVM (DEVM) values computed for each averaging count. This value is expressed as a percentage.
ModAcc:Results:DEVM:Peak RMS DEVM Maximum (%)
Returns the peak of the RMS differential EVM (DEVM) values computed on each 50us block of the EDR portion of the EDR packet. When you set ModAcc Averaging Enabled property to True, it returns the maximum of the peak RMS differential EVM (DEVM) values computed for each averaging count. This value is expressed as a percentage.
ModAcc:Results:DEVM:Percentage of Symbols below 99% DEVM Limit (%)
Returns the percentage of symbols in the EDR portion of all the measured EDR packets with differential EVM (DEVM) less than or equal to 99% DEVM threshold as defined in section 4.5.11 of the Bluetooth Test Specification RF.TS.p33.. When you set the ModAcc Averaging Enabled property to True, it computes this result using the symbol DEVM values from all averaging counts. This value is expressed as a percentage.
ModAcc:Results:DEVM:Phase Error:Average RMS Phase Error Mean (deg)
Return the average of the RMS phase error values computed on each 50 us block of EDR portion of the EDR packet. When you set the ModAcc Averaging Enabled property to True, it returns the mean of the average RMS phase error values computed for each averaging count. This value is expressed in degrees.
ModAcc:Results:DEVM:Phase Error:Peak RMS Phase Error Maximum (deg)
Return the peak of the RMS phase error values computed on each 50 us block of EDR portion of the EDR packet. When you set the ModAcc Averaging Enabled property to True, it returns the maximum of the peak RMS phase error values computed for each averaging count. This value is expressed in degrees.
ModAcc:Results:DEVM:RMS DEVM Mean (%)
Returns the RMS differential EVM (DEVM) value computed on the EDR portion of the EDR packet. When you set the ModAcc Averaging Enabled property to True, it returns the mean of the RMS differential EVM (DEVM) values computed for each averaging count. This value is expressed as a percentage.
ModAcc:Results:EVM:Control Header RMS EVM Mean (dB)
Returns the RMS EVM value computed on the control header portion of the LE-HDT packet. When you set the ModAcc Averaging Enabled property to True, it returns the mean of the RMS EVM values computed for each averaging count. This value is expressed in dB. This result is valid only for LE-HDT packet.
ModAcc:Results:EVM:Payload RMS EVM Mean (dB)
Returns the RMS EVM value computed on the payload portion including the payload header of the LE-HDT packet. When you set the ModAcc Averaging Enabled property to True, it returns the mean of the RMS EVM values computed for each averaging count. This value is expressed in dB. This result is valid only for LE-HDT packet.
ModAcc:Results:EVM:Preamble RMS EVM Mean (dB)
Returns the RMS EVM value computed on the preamble portion of the LE-HDT packet. When you set the ModAcc Averaging Enabled property to True, it returns the mean of the RMS EVM values computed for each averaging count. This value is expressed in dB. This result is valid only for LE-HDT packet.
ModAcc:Results:Fractional Time Offset Mean (s)
Returns the fractional time offset value computed on the sounding sequence portion of the LE CS Packet. This value is expressed in seconds. When you set the ModAcc Averaging Enabled property to True, it returns the mean of the fractional time offset values for each averaging count.
ModAcc:Results:Frequency Error:BR:Initial Frequency Error Maximum (Hz)
Returns the initial frequency error value computed on the preamble portion of the BR packet. When you set the ModAcc Averaging Enabled property to True, it returns the value corresponding to the maximum of the absolute initial frequency error values computed for each averaging count. This value is expressed in Hz.
ModAcc:Results:Frequency Error:BR:Peak Frequency Drift Maximum (Hz)
Returns the peak frequency drift value computed on the BR packet. When you set the ModAcc Averaging Enabled property to True, it returns the value corresponding to the maximum of the absolute peak frequency drift values computed for each averaging count. This value is expressed in Hz.
ModAcc:Results:Frequency Error:BR:Peak Frequency Drift Rate Maximum (Hz)
Returns the peak frequency drift rate value computed on the BR packet. When you set the ModAcc Averaging Enabled property to True, it returns the value corresponding to the maximum of the absolute peak frequency drift rate values computed for each averaging count. This value is expressed in Hz.
ModAcc:Results:Frequency Error:EDR:Header Frequency Error wi Maximum (Hz)
Returns the frequency error value computed on the header of the EDR packet. When you set the ModAcc Averaging Enabled property to True, it returns the value corresponding to the maximum of the absolute header frequency error values computed for each averaging count. This value is expressed in Hz.
ModAcc:Results:Frequency Error:EDR:Peak Frequency Error w0 Maximum (Hz)
Returns the peak frequency error value computed on the EDR portion of the EDR packet, relative to the header frequency error. When you set the ModAcc Averaging Enabled property to True, it returns the value corresponding to the maximum absolute of the peak frequency error values computed for each averaging count. This value is expressed in Hz.
ModAcc:Results:Frequency Error:EDR:Peak Frequency Error wi+w0 Maximum (Hz)
Returns the peak frequency error value computed on the EDR portion of the EDR packet. When you set the ModAcc Averaging Enabled property to True, it returns the value corresponding to the maximum of the absolute peak frequency error values computed for each averaging count. This value is expressed in Hz.
ModAcc:Results:Frequency Error:LE-HDT:Frequency Error w0+w1 Maximum (Hz)
Returns the total frequency error for the LE-HDT packet. When you set the ModAcc Averaging Enabled property to True, it returns a value corresponding to the maximum of the absolute frequency error values computed for each averaging count. This value is expressed in Hz.
ModAcc:Results:Frequency Error:LE-HDT:Payload Frequency Error w1 Maximum (Hz)
Returns the frequency error value computed on the payload portion of the LE-HDT packet. When you set the ModAcc Averaging Enabled property to True, it returns a value corresponding to the maximum of the absolute payload frequency error values computed for each averaging count. This value is expressed in Hz.
ModAcc:Results:Frequency Error:LE-HDT:Preamble Frequency Error w0 Maximum (Hz)
Returns the frequency error value computed on the preamble portion of the LE-HDT packet. When you set the ModAcc Averaging Enabled property to True, it returns a value corresponding to the maximum of the absolute preamble frequency error values computed for each averaging count. This value is expressed in Hz.
ModAcc:Results:Frequency Error:LE:Initial Frequency Drift Maximum (Hz)
Returns the initial frequency drift value computed on the LE packet. When you set the ModAcc Averaging Enabled property to True, it returns the value corresponding to the maximum of the absolute initial frequency drift values computed for each averaging count. This value is expressed in Hz.
ModAcc:Results:Frequency Error:LE:Initial Frequency Error Maximum (Hz)
Returns the initial frequency error value computed on the preamble portion of the LE or LE-CS packet. When you set the ModAcc Averaging Enabled property to True, it returns a value corresponding to the maximum of the absolute initial frequency error values computed for each averaging count. This value is expressed in Hz.
ModAcc:Results:Frequency Error:LE:Peak Frequency Drift Maximum (Hz)
Returns the peak frequency drift value computed on the LE packet. When you set the ModAcc Averaging Enabled property to True, it returns the value corresponding to the maximum of the absolute peak frequency drift values computed for each averaging count. This value is expressed in Hz.
ModAcc:Results:Frequency Error:LE:Peak Frequency Drift Rate Maximum (Hz)
Returns the peak frequency drift rate value computed on the LE packet. When you set the ModAcc Averaging Enabled property to True, it returns the value corresponding to the maximum of the absolute peak frequency drift rate values computed for each averaging count. This value is expressed in Hz.
ModAcc:Results:Frequency Error:LE:Peak Frequency Error Maximum (Hz)
When you set the Direction Finding Mode property to Disabled, it returns the peak frequency error value computed on the preamble and payload portion of the LE or LE-CS packet. When you set the Direction Finding Mode property to Angle of Arrival, it returns the peak frequency error value computed on the Constant tone extension field of the LE packet. When you set the ModAcc Averaging Enabled property to True, it returns the value corresponding to the maximum of absolute the peak frequency error values computed for each averaging count. This value is expressed in Hz.
ModAcc:Results:I/Q Origin Offset Mean (dB)
Returns the I/Q origin offset estimated over the EDR portion of the EDR packets. This value is expressed in dB. When you set the ModAcc Averaging Enabled property to True, it returns the mean of the I/Q origin offset values computed for each averaging count.
ModAcc:Results:Preamble Start Time Mean (s)
Returns the start time of the preamble of LE-CS packet. This value is expressed in seconds. When you set the ModAcc Averaging Enabled property to True, it returns the mean of the preamble start time values computed for each averaging count.
ModAcc:Results:df1:Minimum df1max Minimum (Hz)
Returns the minimum df1max value computed on the signal. The measurement computes df1max deviation values on a packet and reports the minimum value. When you set the ModAcc Averaging Enabled property to True, it returns the minimum of the Min df1max results computed for each averaging count. This value is expressed in Hz.
ModAcc:Results:df1:Peak df1max Maximum (Hz)
Returns the peak df1max value computed on the signal. The measurement computes df1max deviation values on a packet and reports the peak value. When you set the ModAcc Averaging Enabled property to True, it returns the maximum of the peak df1max results computed for each averaging count. This value is expressed in Hz.
ModAcc:Results:df1:Percentage of Symbols above df1max Threshold (%)
Returns the percentage of symbols with df1max values that are greater than the df1max threshold defined by the standard. This result is valid only for the LE packet with a data rate of 125 Kbps. When you set the ModAcc Averaging Enabled property to True, it computes this result using the df1max values from all averaging counts. This value expressed as a percentage.
ModAcc:Results:df1:df1avg Maximum (Hz)
Returns the df1avg value computed on the signal. When you set the ModAcc Averaging Enabled property to True, it returns the maximum of the df1avg results computed for each averaging count. This value is expressed in Hz.
ModAcc:Results:df1:df1avg Mean (Hz)
Returns the df1avg value computed on the signal. When you set the ModAcc Averaging Enabled property to True, it returns the mean of the df1avg results computed for each averaging count. This value is expressed in Hz
ModAcc:Results:df1:df1avg Minimum (Hz)
Returns the df1avg value computed on the signal. When you set the ModAcc Averaging Enabled property to True, it returns the minimum of the df1avg results computed for each averaging count. This value is expressed in Hz.
ModAcc:Results:df2:Minimum df2max Minimum (Hz)
Returns the minimum df2max value computed on the signal. The measurement computes df2max deviation values on a packet and reports the minimum value. When you set the ModAcc Averaging Enabled property to True, it returns the minimum of the Min df2max results computed for each averaging count. This value is expressed in Hz.
ModAcc:Results:df2:Peak df2max Maximum (Hz)
Returns the peak df2max value computed on the signal. The measurement computes df2max deviation values on a packet and reports the peak value. When you set the ModAcc Averaging Enabled property to True, it returns the maximum of the peak df2max results computed for each averaging count. This value is expressed in Hz.
ModAcc:Results:df2:Percentage of Symbols above df2max Threshold (%)
Returns the percentage of symbols with df2max values that are greater than the df2max threshold defined by the standard. When you set the ModAcc Averaging Enabled property to True, it computes this result using the df2max values from all averaging counts. This value is expressed as a percentage.
ModAcc:Results:df2:df2avg Maximum (Hz)
Returns the df2avg value computed on the signal. When you set the ModAcc Averaging Enabled property to True, it returns the maximum of the df2avg results computed for each averaging count. This value is expressed in Hz.
ModAcc:Results:df2:df2avg Mean (Hz)
Returns the df2avg value computed on the signal. When you set the ModAcc Averaging Enabled property to True, it returns the mean of the df2avg results computed for each averaging count. This value is expressed in Hz.
ModAcc:Results:df2:df2avg Minimum (Hz)
Returns the df2avg value computed on the signal. When you set the ModAcc Averaging Enabled property to True, it returns the minimum of the df2avg results computed for each averaging count. This value is expressed in Hz.
ModAcc:Results:df3:df3avg Mean (Hz)
Returns the df3avg value computed on the signal. When you set the ModAcc Averaging Enabled property to True, it returns the mean of the df3avg results computed for each averaging count. This value is expressed in Hz. This result is valid only for LE-CS packet with data rate 2 Mbps and when bandwidth bit period product is set to 2.
ModAcc:Results:df4:Percentage of Symbols above df4avg Threshold (%)
Returns the percentage of symbols with df4avg values that are greater than the df4avg threshold defined by the standard. When you set the ModAcc Averaging Enabled property to True, it computes this result using the df4avg values from all averaging counts. This value is expressed as a percentage. This result is valid only for LE-CS packet with data rate 2 Mbps and when bandwidth bit period product is set to 2.
ModSpectrum:All Traces Enabled
Specifies whether to enable all the traces used for ModSpectrum measurements.
ModSpectrum:Averaging:Count
Specifies the number of acquisitions used for averaging when you set the ModSpectrum Averaging Enabled property to True.
ModSpectrum:Averaging:Enabled
Specifies whether to enable averaging for ModSpectrum measurements.
ModSpectrum:Burst Synchronization Type
Specifies the type of synchronization used for detecting the start of packet in the ModSpectrum measurement.
ModSpectrum:Measurement Enabled
Specifies whether to enable the ModSpectrum measurements.This measurement is valid only for channel sounding (CS) packets.
ModSpectrum:Number of Analysis Threads
Specifies the maximum number of threads used for parallelism for ModSpectrum measurement.
ModSpectrum:Results:Bandwidth (Hz)
Returns the 6 dB bandwidth of the received signal. It is computed as the difference between ModSpectrum Results High Freq and ModSpectrum Results Low Freq . This value is expressed in Hz.
ModSpectrum:Results:High Frequency (Hz)
Returns the highest frequency above the center frequency at which the transmit power drops 6dB below the peak power. This value is expressed in Hz.
ModSpectrum:Results:Low Frequency (Hz)
Returns the lowest frequency below the center frequency at which the transmit power drops 6 dB below the peak power. This value is expressed in Hz.
Packet:Access Address
Specifies the 32-bit LE access address.
Packet:BD Address:LAP
Specifies the 24-bit lower address part (LAP) of the bluetooth device address (BD_ADDR).
Packet:Bandwidth Bit Period Product
Specifies the bandwidth bit period product of GFSK modulation for LE-CS packet type.
Packet:Channel Sounding:Antenna Switch Time (s)
Specifies the Channel Sounding Antenna Switch Time for the LE-CS packet. This property is applicable only when you set the Packet Type property to LE-CS and the CS Packet Format property to any value other than SYNC.
Packet:Channel Sounding:Number of Antenna Path
Specifies the number of antenna paths for the generated LE-CS packet. This property is applicable only when you set the Packet Type property to LE-CS and the CS Packet Format property to any value other than SYNC.
Packet:Channel Sounding:Packet Format
Specifies the format of the Channel Sounding packet depending on the position and presence of SYNC and CS Tone fields. This property is applicable only when you set the Packet Type property to LE-CS.
Packet:Channel Sounding:Phase Measurement Period
Specifies the Channel Sounding Phase Measurement Period for the LE-CS packet. This property is applicable only when you set the Packet Type property to LE-CS and the CS Packet Format property to any value other than SYNC.
Packet:Channel Sounding:SYNC Sequence
Specifies the type of sequence present in the SYNC portion after trailer bits. This property is applicable only when you set the Packet Type property to LE-CS and the CS Packet Format property to any value other than CS Tone.
Packet:Channel Sounding:Tone Extension Slot
Specifies whether the tone extension slot transmission is enabled after CS Tone. This property is applicable only when you set the Packet Type property to LE-CS and the CS Packet Format property to any value other than SYNC.
Packet:Data Rate (bps)
Specifies the data rate of the LE, LE-CS or LE-HDT packet transmitted by the device under test (DUT). This value is expressed in bps. This property is applicable only to LE, LE-CS or LE-HDT packet type.
Packet:Direction Finding:CTE Length (s)
Specifies the length of the constant tone extension (CTE) field in the generated signal. This value is expressed in seconds. This property is applicable only when you set the Direction Finding Mode property to either Angle of Arrival or Angle of Departure.
Packet:Direction Finding:CTE Number of Transmit Slots
Returns the number of transmit slots in the constant time extension portion of the generated LE packet. This property is applicable only when you set the Direction Finding Mode property to Angle of Arrival or Angle of Departure.
Packet:Direction Finding:CTE Slot Duration (s)
Specifies the length of the switching slots and transmit slots in the constant tone extension field in the generated signal. This property is applicable only when you set the Direction Finding Mode property to Angle of Arrival or Angle of Departure.
Packet:Direction Finding:Mode
Specifies the mode of direction finding.
Packet:High Data Throughput: Packet Format
Specifies the Higher Data Throughput (HDT) packet format. This property is applicable only when you set the Packet Type property to LE-HDT.
Packet:High Data Throughput: Zadoff-Chu Index
Specifies Zadoff-Chu Index for the Long Training Sequence in the preamble. Input to the Zadoff-Chu Index property must be in the range of [1 - 16]. This property is applicable only when you set the Packet Type property to LE-HDT.
Packet:High Data Throughput:Number of Block Repetition Sequences
Packet:High Data Throughput:VHDT Mode Enabled
Packet:Payload Bit Pattern
Specifies the bit pattern present in the payload of the packet. This value is used to determine the set of ModAcc measurements to be performed.
Packet:Payload Length (bytes)
Specifies the payload length of BR, EDR, LE and LE-CS packet, and the payload zone length of LE-HDT packet, in bytes. This property is applicable only when you set the Payload Length Mode property to Manual. This property returns the payload length or payload zone length used for measurement if you set the Payload Length Mode property to Auto.
Packet:Payload Length Mode
Specifies the payload length mode of the signal to be measured. The payload length mode and Payload Length properties decide the length of the payload to be used for measurement.
Packet:Type
Specifies the type of the Bluetooth packet to be measured.
PowerRamp:Averaging:Count
Specifies the number of acquisitions used for averaging when you set the PowerRamp Averaging Enabled property to True.
PowerRamp:Averaging:Enabled
Specifies whether to enable averaging for PowerRamp measurement.
PowerRamp:Burst Synchronization Type
Specifies the type of synchronization used for detecting the start of packet in the PowerRamp measurement.
PowerRamp:Measurement Enabled
Specifies whether to enable PowerRamp measurements. This measurement is valid only for low energy CS (LE-CS) packets.
PowerRamp:Number of Analysis Threads
Specifies the maximum number of threads used for parallelism for PowerRamp measurement.
PowerRamp:Results: 40dB Fall Time Mean (s)
40dB Fall Time returns the fall time of the acquired signal at which transmit power drops 40 dB below average power. When you set the PowerRamp Averaging Enabled property to True, this parameter returns the mean of the 40dB fall time computed for each averaging count. This value is expressed in seconds.
PowerRamp:Results:Fall Time Mean (s)
Fall Time returns the fall time of the acquired signal that is the amount of time taken for the power envelope to fall from a level of 90 percent to 10 percent. When you set the PowerRamp Averaging Enabled property to True,this parameter returns the mean of the fall time computed for each averaging countt. This value is expressed in seconds.
PowerRamp:Results:Rise Time Mean (s)
Rise Time returns the rise time of the acquired signal that is the amount of time taken for the power envelope to rise from a level of 10 percent to 90 percent. When you set the PowerRamp Averaging Enabled property to True, this parameter returns the mean of the rise time computed for each averaging count. This value is expressed in seconds.
Reference Level
Specifies the reference level that represents the maximum expected power of the RF input signal. This value is expressed in dBm for RF devices and Vpk-pk for baseband devices.
Reference Level Headroom
Specifies the margin RFmx adds to the Reference Level property. The margin avoids clipping and overflow warnings if the input signal exceeds the configured reference level.
Result Fetch Timeout (s)
Specifies the time, in seconds, to wait before results are available in the RFmxBT Property Node. Set this value to a time longer than expected for fetching the measurement. A value of -1 specifies that the RFmxBT Property Node waits until the measurement is complete.
Selected Ports
Specifies the instrument port to be configured to acquire a signal. Use RFmxInstr Get Available Ports VI to get the valid port names.
Selector String
Specifies the active channel string used to access all subsequent channel-based properties in this instance of the property node.
TXP:All Traces Enabled
Specifies whether to enable all the traces used for transmit power (TxP) measurements.
TXP:Averaging:Count
Specifies the number of acquisitions used for averaging when you set the TXP Averaging Enabled property to True.
TXP:Averaging:Enabled
Specifies whether to enable averaging for the transmit power (TxP) measurements.
TXP:Burst Synchronization Type
Specifies the type of synchronization used for detecting the start of packet in the transmit power (TXP) measurement.
TXP:Measurement Enabled
Specifies whether to enable the transmit power (TxP) measurements.
TXP:Number of Analysis Threads
Specifies the maximum number of threads used for parallelism for TXP measurement.
TXP:Results:Average Power Maximum (dBm)
Returns the average power computed over the measurement interval. When you set the Direction Finding Mode property to Angle of Departure for LE packets, it will exclude guard period and all the switching slots for the average power computation. For LE-HDT, average power is calculated from beginning of the payload portion. When you set the TXP Averaging Enabled property to True, it returns the maximum of the average power results computed for each averaging count. This value is expressed in dBm.
TXP:Results:Average Power Mean (dBm)
Returns the average power computed over the measurement interval. When you set the Direction Finding Mode property to Angle of Departure for LE packets, it will exclude guard period and all the switching slots for the average power computation. For LE-HDT, average power is calculated from beginning of the payload portion. This value is expressed in dBm. When you set the TXP Averaging Enabled property to True, it returns the mean of the average power results computed for each averaging count.
TXP:Results:Average Power Minimum (dBm)
Returns the average power computed over the measurement interval. When you set the Direction Finding Mode property to Angle of Departure for LE packets, it will exclude guard period and all the switching slots for the average power computation. For LE-HDT, average power is calculated from beginning of the payload portion. When you set the TXP Averaging Enabled property to True, it returns the minimum of the average power results computed for each averaging count. This value is expressed in dBm.
TXP:Results:EDR DPSK Average Power Mean (dBm)
Returns the average power of the DPSK portion of the EDR packet. When you set the TXP Averaging Enabled property to True, it returns the mean of the DPSK average power results computed for each averaging count. This value is expressed in dBm.
TXP:Results:EDR DPSK GFSK Average Power Ratio Mean (dB)
Returns the ratio of the average power of the DPSK portion to the average power of the GFSK portion of the EDR packet. When you set the TXP Averaging Enabled property to True, it returns the mean of the DPSK GFSK average power ratio results computed for each averaging count. This value is expressed in dB.
TXP:Results:EDR GFSK Average Power Mean (dBm)
Returns the average power of the GFSK portion of the EDR packet. When you set the TXP Averaging Enabled property to True, it returns the mean of the GFSK average power results computed for each averaging count. This value is expressed in dBm.
TXP:Results:LE CS Phase Measurement Period Average Power Mean (dBm)
Returns the average power computed over each antenna path during phase measurement period of the LE-CS packet. This result is applicable only when you set the Packet Type property to LE-CS and the CS Packet Format property to any value other than SYNC. When you set the TXP Averaging Enabled property to True, it returns the mean of the phase measurement period average power results computed for each averaging count. This value is expressed in dBm.
TXP:Results:LE CTE Reference Period Average Power Mean (dBm)
Returns the average power computed over the reference period in the CTE portion of the LE packet. This result is applicable only when you set the Direction Finding Mode property to Angle of Departure. When you set the TXP Averaging Enabled property to True, it returns the mean of the CTE reference period average power results computed for each averaging count. This value is expressed in dBm.
TXP:Results:LE CTE Reference Period Peak Absolute Power Deviation Maximum (%)
Returns the peak absolute power deviation computed over the reference period in the CTE portion of the LE packet. The peak absolute power deviation is the deviation of peak power with respect to the average power in the reference period. This result is applicable only when you set the Direction Finding Mode property to Angle of Departure. When you set the TXP Averaging Enabled property to True, it returns the maximum of the CTE reference period absolute power deviation results computed for each averaging count. This value is expressed as a percentage.
TXP:Results:LE CTE Transmit Slot Average Power Mean (dBm)
Returns the average power computed over each transmit slot in CTE portion of the LE packet. This result is applicable only when you set the Direction Finding Mode property to Angle of Departure. When you set the TXP Averaging Enabled property to True, it returns the mean of the CTE transmit slot average power results computed for each averaging count. This value is expressed in dBm.
TXP:Results:LE CTE Transmit Slot Peak Absolute Power Deviation Maximum (%)
Returns the peak absolute power deviation computed over each transmit slot in the CTE portion of the LE packet. The peak absolute power deviation is the deviation of peak power in each transmit slot with respect to the average power in that transmit slot. This result is applicable only when you set the Direction Finding Mode property to Angle of Departure. When you set the TXP Averaging Enabled property to True, it returns the maximum of the CTE transmit slot absolute power deviation results computed for each averaging count. This value is expressed as a percentage.
TXP:Results:Peak Power Maximum (dBm)
Returns the peak power computed over the measurement interval. When you set the Direction Finding Mode property to Angle of Departure for LE packets, it will exclude guard period and all the switching slots for the peak power computation. When you set the TXP Averaging Enabled property to True, it returns the maximum of the peak power results computed for each averaging count. This value is expressed in dBm.
TXP:Results:Peak to Average Power Ratio Maximum (dB)
Returns the peak to average power ratio computed over the measurement interval. When you set the Direction Finding Mode property to Angle of Departure for LE packets, it will exclude guard period and all the switching slots for the peak to average power ratio computation. For LE-HDT, PAPR is calculated using peak power calculated over active portion of burst and average power calculated from beginning of the payload portion. When you set the TXP Averaging Enabled property to True, it returns the maximum of the peak to average power ratio results computed for each averaging count. This value is expressed in dB.
Trigger:Delay (s)
Specifies the trigger delay time. This value is expressed in seconds.
Trigger:Digital Edge:Edge
Specifies the active edge for the trigger. This property is valid only when you set the Trigger Type property to Digital Edge.
Trigger:Digital Edge:Source
Specifies the source terminal for the digital edge trigger. This property is used only when you set the Trigger Type property to Digital Edge.
Trigger:IQ Power Edge:Level (dB or dBm)
Specifies the power level at which the device triggers. The device asserts the trigger when the signal exceeds the level specified by the value of this parameter, taking into consideration the specified slope.
Trigger:IQ Power Edge:Level Type
Specifies the reference for the IQ Power Edge Level property. The IQ Power Edge Level Type property is used only when you set the Trigger Type property to IQ Power Edge.
Trigger:IQ Power Edge:Slope
Specifies whether the device asserts the trigger when the signal power is rising or when it is falling. The device asserts the trigger when the signal power exceeds the specified level with the slope you specify. This property is used only when you set the Trigger Type property to IQ Power Edge.
Trigger:IQ Power Edge:Source
Specifies the channel from which the device monitors the trigger. This property is valid only when you set the Trigger Type property to IQ Power Edge.
Trigger:Minimum Quiet Time:Duration (s)
Specifies the time duration for which the signal must be quiet before the signal analyzer arms the I/Q power edge trigger. This value is expressed in seconds.
Trigger:Minimum Quiet Time:Mode
Specifies whether the measurement computes the minimum quiet time used for triggering.
Trigger:Type
Specifies the type of trigger to be used for signal acquisition.

RFmx Bluetooth LabVIEW Reference

Log in to get a better experience