Use the RFmxEVDO properties to access options for configuring and fetching measurements.

© 2015–2025 National Instruments Corporation. All rights reserved.

ACP:Advanced:Far IF Output Power Offset (dB)
Specifies the offset by which to adjust the IF output power level for offset channels that are far from the carrier channel to improve the dynamic range. This value is expressed in dB. This property is used only if you set the ACP Meas Method property to Dynamic Range and set the ACP IF Output Power Offset Auto property to False.
ACP:Advanced:IF Output Power Offset Auto
Specifies whether the measurement calculates an IF output power level offset for the offset channels to improve the dynamic range of the adjacent channel power (ACP) measurement. This property is used only if you set the ACP Meas Method property to Dynamic Range.
ACP:Advanced:Near IF Output Power Offset (dB)
Specifies the offset by which to adjust the IF output power level for offset channels that are near the carrier channel to improve the dynamic range. This value is expressed in dB. This property is used only if you set the ACP Meas Method property to Dynamic Range and set the ACP IF Output Power Offset Auto property to False.
ACP:Advanced:Sequential FFT Size
Specifies the number of bins to use for FFT computation when the ACP Meas Method property is set to Sequential FFT.
ACP:All Traces Enabled
Specifies whether to enable the traces to be stored and retrieved after performing the ACP measurement.
ACP:Averaging:Count
Specifies the number of acquisitions used for averaging when you set the ACP Averaging Enabled property to True.
ACP:Averaging:Enabled
Specifies whether to enable averaging for the ACP measurement.
ACP:Averaging:Type
Specifies the averaging type for averaging multiple spectrum acquisitions. The averaged spectrum is used for ACP measurement.
ACP:Carrier:Integration Bandwidth (Hz)
Returns the ACP carrier integration bandwidth. This value is expressed in Hz.
ACP:FFT:Overlap (%)
Returns the number of samples to overlap between consecutive chunks while performing FFT.
ACP:FFT:Overlap Mode
Specifies how the FFT overlap is applied to the acquired samples.
ACP:Measurement Enabled
Specifies whether to enable the ACP measurement.
ACP:Measurement Method
Specifies the method for performing the adjacent channel power (ACP) measurement.
ACP:Noise Compensation Enabled
Specifies whether to enable compensation of the channel powers for the inherent noise floor of the signal analyzer.
ACP:Number of Analysis Threads
Specifies the maximum number of threads used for parallelism for adjacent channel power (ACP) measurement.
ACP:Offset:Frequency (Hz)
Returns the frequency of an ACP offset channel relative to the carrier frequency. This value is expressed in Hz.
ACP:Offset:Integration Bandwidth (Hz)
Returns the integration bandwidth of an ACP offset channel. This value is expressed in Hz.
ACP:Offset:Number of Offsets
Specifies the number of offset channels for the adjacent channel power (ACP) measurement.
ACP:Offset:Power Reference:Carrier
Specifies the carrier number that is used as the power reference to measure the offset channel relative power.
ACP:Offset:Power Reference:Specific
Specifies the index of the carrier used as the reference carrier. The power measured in this carrier is used as the power reference for measuring the offset channel relative power when you set the ACP Offset Pwr Ref Carrier property to Specific.
ACP:RBW Filter:Auto Bandwidth
Specifies whether the measurement computes the RBW.
ACP:RBW Filter:Bandwidth (Hz)
Specifies the bandwidth of the RBW filter, used to sweep the acquired signal, when you set the ACP RBW Auto property to False. This value is expressed in Hz.
ACP:RBW Filter:Type
Specifies the shape of the digital RBW filter.
ACP:Results:Carrier:Absolute Power (dBm)
Returns the absolute measured carrier power. This value is expressed in dBm.
ACP:Results:Carrier:Relative Power (dB)
Returns the relative measured carrier power. This value is expressed in dB.
ACP:Results:Lower Offset:Absolute Power (dBm)
Returns the absolute measured lower offset channel power. This value is expressed in dBm.
ACP:Results:Lower Offset:Relative Power (dB)
Returns the lower offset channel power measured relative to the integrated power of the power reference carrier. This value is expressed in dB.
ACP:Results:Total Carrier Power (dBm)
Returns the total carrier power measured by the adjacent channel power (ACP) measurement. This value is expressed in dBm.
ACP:Results:Upper Offset:Absolute Power (dBm)
Returns the absolute measured upper offset channel power. This value is expressed in dBm.
ACP:Results:Upper Offset:Relative Power (dB)
Returns the upper offset channel power measured relative to the integrated power of the power reference carrier. This value is expressed in dB.
ACP:Sweep Time:Auto
Specifies whether the measurement computes the sweep time.
ACP:Sweep Time:Interval (s)
Specifies the sweep time when you set the ACP Sweep Time Auto property to False. This value is expressed in seconds.
Advanced:Auto Level Initial Reference Level (dBm)
Specifies the reference level at which the auto leveling process starts finding the optimal reference level. This value is expressed in dBm.
Advanced:Limited Configuration Change
Specifies the set of properties that are considered by RFmx in the locked signal configuration state.
Band Class
Specifies the band in which the channel is located as defined in Section: 1.5, Table 1.5- Band Class List, of the 3GPP2 C.S0057-F specification v1.0.
CDA:All Traces Enabled
Specifies whether to enable the traces after performing the CDA measurement.
CDA:IQ Gain Imbalance Removal Enabled
Specifies whether to remove the I/Q gain imbalance before the CDA measurement.
CDA:IQ Offset Removal Enabled
Specifies whether to remove the I/Q offset before the CDA measurement.
CDA:IQ Quadrature Error Removal Enabled
Specifies whether to remove the I/Q quadrature error before the CDA measurement.
CDA:Measurement Channel:Uplink:Branch
Specifies the Walsh branch of the channel, subject to channel-specific analysis.
CDA:Measurement Channel:Uplink:Walsh Code Length
Specifies the Walsh code length of the channel, subject to channel-specific analysis.
CDA:Measurement Channel:Uplink:Walsh Code Number
Specifies the Walsh code number of the channel, subject to channel-specific analysis.
CDA:Measurement Enabled
Specifies whether to enable the CDA measurement.
CDA:Measurement Length (slots)
Specifies the duration of the CDA measurement. This value is expressed in slots.
CDA:Measurement Offset (slots)
Specifies the measurement offset to skip from the synchronization boundary. This value is expressed in slots. The synchronization boundary is specified by the CDA Sync Mode property.
CDA:Power Unit
Specifies the measurement unit of the code domain power results.
CDA:Receive Filter Enabled
Specifies whether to enable receive filtering.
CDA:Results:Chip Rate Error (ppm)
Returns the chip rate error. This value is expressed in ppm.
CDA:Results:Frequency Error (Hz)
Returns the frequency error. This value is expressed in Hz.
CDA:Results:I/Q Gain Imbalance (dB)
Returns the I/Q gain imbalance. This value is expressed in dB.
CDA:Results:I/Q Origin Offset (dB)
Returns the I/Q origin offset. This value is expressed in dB.
CDA:Results:I/Q Quadrature Error (deg)
Returns the I/Q quadrature error. This value is expressed in degrees.
CDA:Results:Uplink:I Mean Active Power (dB or dBm)
Returns the average power of all active code channels measured on the I-branch. If you set the CDA Power Unit property to dBm, the measurement returns the absolute measured power in dBm. Otherwise, the measurement returns the value relative to the total power in dB.
CDA:Results:Uplink:I Peak Inactive Power (dB or dBm)
Returns the largest measured code power among the set of inactive channels on the I-branch, and in the code domain of the base spreading factor. The base spreading factor depends on the configured physical layer subtype, and is 16 for subtype 0/1; 32 otherwise. If you set the CDA Power Unit property to dBm, the measurement returns the absolute measured power in dBm. Otherwise, the measurement returns the value relative to the total power in dB.
CDA:Results:Uplink:Mean Active Power (dB or dBm)
Returns the average power of all active code channels. If you set the CDA Power Unit property to dBm, the measurement returns the absolute measured power in dBm. Otherwise, the measurement returns the value relative to the total power in dB.
CDA:Results:Uplink:Mean Auxiliary Pilot Power (dB or dBm)
Returns the mean power of the Reverse Auxiliary Pilot Channel (R-APICH). This value is expressed in dB or dBm.
CDA:Results:Uplink:Mean Inactive Power (dB or dBm)
Returns the average code power measured among the set of inactive channels in the code domain of the base spreading factor. The base spreading factor depends on the configured physical layer subtype and is 16 for subtype 0/1; 32 otherwise. If you set the CDA Power Unit property to dBm, the measurement returns the absolute measured power in dBm. Otherwise, the measurement returns the value relative to the total power in dB.
CDA:Results:Uplink:Mean Pilot Power (dB or dBm)
Returns the mean power of the Reverse Pilot channel (R-PICH). This value is expressed in dB or dBm.
CDA:Results:Uplink:Mean Symbol Power (dB or dBm)
Returns the mean symbol power of the configured measurement channel. This value is expressed in dB or dBm.
CDA:Results:Uplink:Peak Active Power (dB or dBm)
Returns the maximum power among all the active code channels. If you set the CDA Power Unit property to dBm, the measurement returns the absolute measured power in dBm. Otherwise, the measurement returns the value relative to the total power in dB.
CDA:Results:Uplink:Peak Inactive Power (dB or dBm)
Returns the largest measured code power among the set of inactive channels in the code domain of the base spreading factor. The base spreading factor depends on the configured physical layer subtype, and is 16 for subtype 0/1; 32 otherwise. If you set the CDA Power Unit property to dBm, the measurement returns the absolute measured power in dBm. Otherwise, the measurement returns the value relative to the total power in dB.
CDA:Results:Uplink:Peak Symbol EVM (%)
Returns the peak symbol EVM of the configured measurement channel. This value is expressed as a percentage.
CDA:Results:Uplink:Q Mean Active Power (dB or dBm)
Returns the average power of all active code channels measured on the Q-branch. If you set the CDA Power Unit property to dBm, the measurement returns the absolute measured power in dBm. Otherwise, the measurement returns the value relative to the total power in dB.
CDA:Results:Uplink:Q Peak Inactive Power (dB or dBm)
Returns the largest measured code power among the set of inactive channels on the Q-branch, and in the code domain of the base spreading factor. This value is expressed in dB or dBm. The base spreading factor depends on the configured physical layer subtype, and is 16 for subtype 0/1, and 32 otherwise.
CDA:Results:Uplink:RMS Symbol EVM (%)
Returns the RMS symbol EVM of the configured measurement channel. This value is expressed as a percentage.
CDA:Results:Uplink:RMS Symbol Magnitude Error (%)
Returns the RMS symbol magnitude error of the configured measurement channel. This value is expressed as a percentage.
CDA:Results:Uplink:RMS Symbol Phase Error (deg)
Returns the RMS symbol phase error of the configured measurement channel. This value is expressed in degrees.
CDA:Results:Uplink:Total Active Power (dB or dBm)
Returns the sum of the powers of all active code channels. If you set the CDA Power Unit property to dBm, the measurement returns the absolute measured power in dBm. Otherwise, the measurement returns the value relative to the total power in dB.
CDA:Results:Uplink:Total Power (dBm)
Returns the mean power of the received signal. This value is expressed in dBm.
CDA:Spectrum Inverted
Specifies whether the signal spectrum is inverted.
CDA:Synchronization Mode
Specifies whether the measurement is performed from the frame, slot, or symbol boundary.
CHP:All Traces Enabled
Specifies whether to enable the traces to be stored and retrieved after performing the channel power (CHP) measurement.
CHP:Averaging:Count
Specifies the number of acquisitions used for averaging when you set the CHP Averaging Enabled property to True.
CHP:Averaging:Enabled
Specifies whether to enable averaging for the channel power (CHP) measurement.
CHP:Averaging:Type
Specifies the averaging type for averaging multiple spectrum acquisitions. The averaged spectrum is used for the channel power (CHP) measurement.
CHP:Carrier Integration Bandwidth (Hz)
Returns the CHP carrier integration bandwidth. This value is expressed in Hz.
CHP:Measurement Enabled
Specifies whether to enable the channel power (CHP) measurement.
CHP:Number of Analysis Threads
Specifies the maximum number of threads used for parallelism for the channel power (CHP) measurement.
CHP:RBW Filter:Auto Bandwidth
Specifies whether the measurement computes the RBW.
CHP:RBW Filter:Bandwidth (Hz)
Specifies the bandwidth of the RBW filter, used to sweep the acquired signal, when you set the CHP RBW Auto property to False. This value is expressed in Hz.
CHP:RBW Filter:Type
Specifies the shape of the digital RBW filter.
CHP:Results:Carrier:Absolute Power (dBm)
Returns the absolute averaged channel power (CHP) for a specific carrier. This value is expressed in dBm.
CHP:Results:Carrier:Relative Power (dB)
Returns the relative averaged channel power (CHP) for a specific carrier. This value is expressed in dB.
CHP:Results:Total Carrier Power (dBm)
Returns the sum of all the active carrier powers. This value is expressed in dBm.
CHP:Sweep Time:Auto
Specifies whether the measurement computes the sweep time.
CHP:Sweep Time:Interval (s)
Specifies the sweep time when you set the CHP Sweep Time Auto property to False. This value is expressed in seconds.
Carrier:Channel:Configuration Mode
Specifies whether to detect the channels automatically or to use a specified channel configuration.
Carrier:Channel:User Defined:Uplink:Branch
Specifies the quadrature branch on which a specific user defined-channel is mapped. This property is used only when you set the Channel Configuration Mode property to User Defined.
Carrier:Channel:User Defined:Uplink:Data Modulation Type
Defines the modulation of the data channel. This property is used only when you set the Channel Configuration Mode property to User Defined.
Carrier:Channel:User Defined:Uplink:Number of Channels
Specifies the number of user-defined channels. This property is used only when you set the Channel Configuration Mode property to User Defined.
Carrier:Channel:User Defined:Uplink:Walsh Code Length
Specifies the Walsh Code Length of a specific user-defined channel. This property is used only when you set the Channel Configuration Mode property to User Defined.
Carrier:Channel:User Defined:Uplink:Walsh Code Number
Specifies the Walsh Code Number of a specific user-defined channel. This property is used only when you set the Channel Configuration Mode property to User Defined.
Carrier:Frequency (Hz)
Specifies the carrier frequency of the RF signal to acquire. This value is expressed in Hz. The signal analyzer tunes to this frequency.
Carrier:Number of Carriers
Specifies the number of carriers in the signal.
Carrier:Physical Layer Subtype
Selects the EV-DO physical layer subtype.
Carrier:Spreading:Uplink:I mask
Specifies the long code mask of the in-phase (I) channel.
Carrier:Spreading:Uplink:Q mask
Specifies the long code mask of the quadrature (Q) channel.
Center Frequency (Hz)
Specifies the carrier frequency of the RF signal to acquire. The signal analyzer tunes to this frequency. This value is expressed in Hz.
External Attenuation (dB)
Specifies the attenuation of a switch or cable connected to the RF IN connector of the signal analyzer. This value is expressed in dB.
ModAcc:All Traces Enabled
Specifies whether to enable the traces to be stored and retrieved after performing the ModAcc measurement.
ModAcc:IQ Gain Imbalance Removal Enabled
Specifies whether to remove the I/Q gain imbalance before the EVM measurement.
ModAcc:IQ Offset Removal Enabled
Specifies whether to remove the I/Q offset before the EVM measurement.
ModAcc:IQ Quadrature Error Removal Enabled
Specifies whether to remove the I/Q quadrature error before the EVM measurement.
ModAcc:Measurement Enabled
Specifies whether to enable the ModAcc measurement.
ModAcc:Measurement Length (slots)
Specifies the duration of the modulation accuracy measurement.
ModAcc:Measurement Offset (slots)
Specifies the measurement offset to skip from the synchronization boundary. This value is expressed in slots. The synchronization boundary is specified by the ModAcc Sync Mode property.
ModAcc:Multi Carrier Filter:Enabled
Enables the multi-carrier filter that can increase the multi-carrier interference suppression to improve ModAcc measurement quality in the presence of neighboring carriers.
ModAcc:Receive Filter Enabled
Specifies whether to enable receive filtering.
ModAcc:Results:Chip Rate Error (ppm)
Returns the chip rate error averaged over all measured slots. This value is expressed in parts per million (ppm).
ModAcc:Results:Frequency Error (Hz)
Returns the frequency error averaged over all measured slots. This value is expressed in Hz.
ModAcc:Results:I/Q Gain Imbalance (dB)
Returns the I/Q gain imbalance of the composite signal, averaged over all measured slots. This value is expressed in dB.
ModAcc:Results:I/Q Origin Offset (dB)
Returns the I/Q origin offset of the composite signal, averaged over all measured slots. This value is expressed in dB.
ModAcc:Results:I/Q Quadrature Error (deg)
Returns the I/Q quadrature error of the composite signal, averaged over all measured slots. This value is expressed in degrees.
ModAcc:Results:Uplink:Detected Channels:Branch
Returns the quadrature branch of a particular detected channel.
ModAcc:Results:Uplink:Detected Channels:Code Length
Returns the Walsh Code length of a detected channel.
ModAcc:Results:Uplink:Detected Channels:Code Number
Returns the Walsh Code number of a detected channel.
ModAcc:Results:Uplink:Detected Data Modulation Type
Returns the modulation type of the uplink data channel.
ModAcc:Results:Uplink:Number of Detected Channels
Returns the total number of detected channels.
ModAcc:Results:Uplink:Peak Active CDE (dB)
Returns the peak code domain error (CDE) value among the active Walsh channels. This value is expressed in dB.
ModAcc:Results:Uplink:Peak Active CDE Branch
Returns the quadrature branch of the channel corresponding to the Peak Active CDE (dB) result.
ModAcc:Results:Uplink:Peak Active CDE Walsh Code Length
The Walsh code length of the active Walsh channel for which the peak CDE has been observed.
ModAcc:Results:Uplink:Peak Active CDE Walsh Code Number
Returns the Walsh code number of the channel corresponding to the ModAcc:Uplink:Peak Active CDE (dB) result.
ModAcc:Results:Uplink:Peak CDE (dB)
Returns the peak uplink code domain error (CDE), expressed in dB.
ModAcc:Results:Uplink:Peak CDE Branch
Returns the branch of the channel corresponding to the Peak Active CDE (dB) property result.
ModAcc:Results:Uplink:Peak CDE Walsh Code Number
Returns the Walsh code number of the channel corresponding to the ModAcc:Uplink:Peak CDE (db) result.
ModAcc:Results:Uplink:Peak EVM (%)
Returns the peak value of the uplink error vector magnitude (EVM), averaged over all measured slots. This value is expressed as a percentage.
ModAcc:Results:Uplink:RMS EVM (%)
Returns the RMS of the uplink error vector magnitude (EVM), averaged over all measured slots. This value is expressed as a percentage.
ModAcc:Results:Uplink:RMS Magnitude Error (%)
Returns the RMS of the magnitude error. This value is expressed as a percentage.
ModAcc:Results:Uplink:RMS Phase Error (Deg)
Returns the RMS of the phase error. This value is expressed in degrees.
ModAcc:Results:Uplink:Rho
Returns the measured Rho value of the analyzed signal.
ModAcc:Spectrum Inverted
Specifies whether the measured spectrum is inverted.
ModAcc:Synchronization Mode
Specifies whether the measurement is performed from frame, slot, or symbol boundary.
OBW:All Traces Enabled
Specifies whether to enable the traces to be stored and retrieved after performing the occupied bandwidth (OBW) measurement.
OBW:Averaging:Count
Specifies the number of acquisitions used for averaging when you set the OBW Averaging Enabled property to True.
OBW:Averaging:Enabled
Specifies whether to enable averaging for the occupied bandwidth (OBW) measurement.
OBW:Averaging:Type
Specifies the averaging type for averaging multiple spectrum acquisitions. The averaged spectrum is used for occupied bandwidth (OBW) measurement.
OBW:Measurement Enabled
Specifies whether to enable the occupied bandwidth (OBW) measurement.
OBW:Number of Analysis Threads
Specifies the maximum number of threads used for parallelism for the occupied bandwidth (OBW) measurement.
OBW:RBW Filter:Auto Bandwidth
Specifies whether the measurement computes the RBW.
OBW:RBW Filter:Bandwidth (Hz)
Specifies the bandwidth of the RBW filter, used to sweep the acquired signal, when you set the OBW RBW Auto property to False. This value is expressed in Hz.
OBW:RBW Filter:Type
Specifies the shape of the digital RBW filter.
OBW:Results:Absolute Power (dBm)
Returns the absolute power measured in the occupied bandwidth (OBW). This value is expressed in dBm.
OBW:Results:Occupied Bandwidth (Hz)
Returns the bandwidth that occupies 99 percent of the total power of the signal. This value is expressed in Hz.
OBW:Results:Start Frequency (Hz)
Returns the start frequency of the occupied bandwidth (OBW). This value is expressed in Hz.
OBW:Results:Stop Frequency (Hz)
Returns the stop frequency of the occupied bandwidth (OBW). This value is expressed in Hz.
OBW:Span (Hz)
Returns the frequency span of the OBW measurement. This value is expressed in Hz.
OBW:Sweep Time:Auto
Specifies whether the measurement computes the sweep time.
OBW:Sweep Time:Interval (s)
Specifies the sweep time when you set the OBW Sweep Time Auto property to False. This value is expressed in seconds.
Reference Level
Specifies the reference level that represents the maximum expected power of the RF input signal. This value is expressed in dBm for RF devices and Vpk-pk for baseband devices.
Reference Level Headroom
Specifies the margin RFmx adds to the Reference Level property. The margin avoids clipping and overflow warnings if the input signal exceeds the configured reference level.
Result Fetch Timeout (s)
Specifies the time to wait before results are available in the RFmxEVDO Property Node. This value is expressed in seconds. Set this value to a time longer than expected for fetching the measurement. A value of -1 specifies that the RFmxEVDO Property Node waits until the measurement is complete.
SEM:All Traces Enabled
Specifies whether to enable the traces to be stored and retrieved after performing the spectral emissions mask (SEM) measurement.
SEM:Averaging:Count
Specifies the number of acquisitions used for averaging when you set the SEM Averaging Enabled property to True.
SEM:Averaging:Enabled
Specifies whether to enable averaging for the spectral emissions mask (SEM) measurement.
SEM:Averaging:Type
Specifies the averaging type for averaging multiple spectrum acquisitions. The averaged spectrum is used for the spectral emissions mask (SEM) measurement.
SEM:Carrier:Integration Bandwidth (Hz)
Returns the SEM carrier integration bandwidth. This value is expressed in Hz.
SEM:Measurement Enabled
Specifies whether to enable the spectral emissions mask (SEM) measurement.
SEM:Number of Analysis Threads
Specifies the maximum number of threads used for parallelism for the spectral emissions mask (SEM) measurement.
SEM:Offset:Bandwidth Integral
Returns the bandwidth integral for a specific offset segment.
SEM:Offset:Number of Offsets
Returns the number of SEM offset segments.
SEM:Offset:RBW Filter:Bandwidth (Hz)
Returns the bandwidth of the RBW filter used to sweep the offset segment. This value is expressed in Hz.
SEM:Offset:RBW Filter:Type
Returns the type of RBW filter used to sweep the offset segment.
SEM:Offset:Start Frequency (Hz)
Returns the start frequency of an SEM offset segment relative to the carrier frequency. This value is expressed in Hz.
SEM:Offset:Stop Frequency (Hz)
Returns the stop frequency of an SEM offset segment relative to the carrier frequency. This value is expressed in Hz.
SEM:Results:Carrier:Absolute Integrated Power (dBm)
Returns the absolute carrier power measurement. This value is expressed in dBm.
SEM:Results:Carrier:Absolute Peak Power (dBm)
Returns the peak absolute carrier power. This value is expressed in dBm.
SEM:Results:Carrier:Peak Frequency (Hz)
Returns the frequency at which the peak power occurs in the carrier channel. This value is expressed in Hz.
SEM:Results:Carrier:Relative Integrated Power (dB)
Returns the relative carrier power measurement. This value is expressed in dB.
SEM:Results:Composite Measurement Status
Indicates the overall measurement status based on the measurement limits and the failure criteria specified by the standard for each offset segment.
SEM:Results:Lower Offset:Absolute Integrated Power (dBm)
Returns the absolute power measured in the lower (negative) offset segment. This value is expressed in dBm.
SEM:Results:Lower Offset:Absolute Peak Power (dBm)
Returns the peak absolute power measured in the lower (negative) offset segment. This value is expressed in dBm.
SEM:Results:Lower Offset:Margin (dB)
Returns the margin from the limit mask value specified by the standard. This value is expressed in dB.
SEM:Results:Lower Offset:Margin Absolute Power (dBm)
Returns the absolute power at which the margin occurred in the lower (negative) offset segment. This value is expressed in dBm.
SEM:Results:Lower Offset:Margin Frequency (Hz)
Returns the frequency at which the margin occurred in the lower (negative) offset segment. This value is expressed in Hz.
SEM:Results:Lower Offset:Margin Relative Power (dB)
Returns the power at which the margin occurred in the lower (negative) offset segment relative to the integrated power of the reference carrier. This value is expressed in dB.
SEM:Results:Lower Offset:Measurement Status
Indicates the lower offset segment measurement status based on measurement limits and the failure criteria specified by the standard.
SEM:Results:Lower Offset:Peak Frequency (Hz)
Returns the frequency at which the peak power occurred in the lower offset segment. This value is expressed in Hz.
SEM:Results:Lower Offset:Relative Integrated Power (dB)
Returns the power measured in the lower (negative) offset segment relative to the integrated power of the reference carrier.
SEM:Results:Lower Offset:Relative Peak Power (dB)
Returns the peak power measured in the lower (negative) offset segment relative to the integrated power of the reference carrier. This value is expressed in dB.
SEM:Results:Total Carrier Power (dBm)
Returns the total carrier power of the selected carrier. This value is expressed in dBm.
SEM:Results:Upper Offset:Absolute Integrated Power (dBm)
Returns the absolute power measured in the upper (positive) offset segment. This value is expressed in dBm.
SEM:Results:Upper Offset:Absolute Peak Power (dBm)
Returns the peak absolute power measured in the upper (positive) offset segment. This value is expressed in dBm.
SEM:Results:Upper Offset:Margin (dB)
Returns the margin from the limit mask value specified by the standard. This value is expressed in dB.
SEM:Results:Upper Offset:Margin Absolute Power (dBm)
Returns the power at which the margin occurred in the upper (positive) offset segment, relative to the integrated power of the reference carrier. This value is expressed in dBm.
SEM:Results:Upper Offset:Margin Frequency (Hz)
Returns the frequency at which the margin occurred in the upper (positive) offset. This value is expressed in Hz.
SEM:Results:Upper Offset:Margin Relative Power (dB)
Returns the power at which the margin occurred in the upper (positive) offset segment relative to the integrated power of the reference carrier. This value is expressed in dB.
SEM:Results:Upper Offset:Measurement Status
Indicates the upper offset measurement status based on measurement limits and the failure criteria specified by the standard.
SEM:Results:Upper Offset:Peak Frequency (Hz)
Returns the frequency at which the peak power occurred in the upper offset segment. This value is expressed in Hz.
SEM:Results:Upper Offset:Relative Integrated Power (dB)
Returns the power measured in the upper (positive) offset segment relative to the integrated power of the reference carrier. This value is expressed in dB.
SEM:Results:Upper Offset:Relative Peak Power (dB)
Returns the peak power measured in the upper (positive) offset segment relative to the integrated power of the reference carrier. This value is expressed in dB.
SEM:Sweep Time:Auto
Specifies whether the measurement computes the sweep time.
SEM:Sweep Time:Interval (s)
Specifies the sweep time when you set the SEM Sweep Time Auto property to False. This value is expressed in seconds.
Selected Ports
Specifies the instrument port to be configured to acquire a signal. Use RFmxInstr Get Available Ports VI to get the valid port names.
Selector String
Specifies the selector string used to access all subsequent channel-based properties in this instance of the property node.
SlotPhase:All Traces Enabled
Specifies whether to enable the traces after performing the SlotPhase measurement.
SlotPhase:Measurement Enabled
Specifies whether to enable the SlotPhase measurement.
SlotPhase:Measurement Length (slots)
Specifies the duration of the SlotPhase measurement. This value is expressed in slots.
SlotPhase:Measurement Offset (slots)
Specifies the measurement offset to skip from the synchronization boundary. This value is expressed in slots. The synchronization boundary is specified by the SlotPhase Sync Modeproperty.
SlotPhase:Receive Filter Enabled
Specifies whether to enable receive filtering.
SlotPhase:Results:Maximum Half Slot Phase Discontinuity (deg)
Returns the maximum slot phase discontinuity value observed in the measurement interval. This value is expressed in degrees.
SlotPhase:Spectrum Inverted
Specifies whether the signal spectrum is inverted.
SlotPhase:Synchronization Mode
Specifies whether the measurement is performed from the frame or the slot boundary.
SlotPhase:Transient Duration (s)
Specifies the transient duration for the SlotPhase measurement. This value is expressed in seconds.
SlotPower:Measurement Enabled
Specifies whether to enable the SlotPower measurement.
SlotPower:Measurement Length (slots)
Specifies the duration of the SlotPower measurement. This value is expressed in slots.
SlotPower:Measurement Offset (slots)
Specifies the measurement offset to skip from the synchronization boundary. This value is expressed in slots. The synchronization boundary is specified by the SlotPower Sync Mode property.
SlotPower:Receive Filter Enabled
Specifies whether to enable receive filtering.
SlotPower:Spectrum Inverted
Specifies whether the signal spectrum is inverted.
SlotPower:Synchronization Mode
Specifies whether the measurement is performed from the frame or the slot boundary.
Trigger:Delay (s)
Specifies the trigger delay time. This value is expressed in seconds.
Trigger:Digital Edge:Edge
Specifies the active edge for the trigger. This property is used only when you set the Trigger Type property to Digital Edge.
Trigger:Digital Edge:Source
Specifies the source terminal for the digital edge trigger. This property is used only when you set the Trigger Type property to Digital Edge.
Trigger:IQ Power Edge:Level (dB or dBm)
Specifies the power level at which the device triggers. This value is expressed in dB when the IQ Power Edge Level Type property is set to Relative and in dBm when the IQ Power Edge Level Type property is set to Absolute. The device asserts the trigger when the signal exceeds the level specified by the value of this property, taking into consideration the specified slope. This property is used only when you set the Trigger Type property to IQ Power Edge.
Trigger:IQ Power Edge:Level Type
Specifies the reference for the IQ Power Edge Level property. This property is used only when you set the Trigger Type property to IQ Power Edge.
Trigger:IQ Power Edge:Slope
Specifies whether the device asserts the trigger when the signal power is rising or when it is falling. The device asserts the trigger when the signal power exceeds the specified level with the slope you specify. This property is used only when you set the Trigger Type property to IQ Power Edge.
Trigger:IQ Power Edge:Source
Specifies the channel from which the device monitors the trigger. This property is used only when you set the Trigger Type property to IQ Power Edge.
Trigger:Minimum Quiet Time:Duration (s)
Specifies the time duration for which the signal must be quiet before the signal analyzer arms the I/Q power edge trigger. This value is expressed in seconds. If you set the IQ Power Edge Slope property to Rising Slope, the signal is quiet below the trigger level. If you set the IQ Power Edge Slope property to Falling Slope, the signal is quiet above the trigger level.
Trigger:Minimum Quiet Time:Mode
Specifies whether the measurement computes the minimum quiet time used for triggering.
Trigger:Type
Specifies the trigger type.

RFmx EV-DO LabVIEW Reference