NationalInstruments.RFmx.BTMX

Defines a root class which is used to identify and control BT signal configuration.

Represents the ACP measurement.

Provides methods to configure the ACP measurement.

Provides methods to fetch and read the ACP measurement results.

Specifies constants for I/O terminals.

Represents the FrequencyRange measurement.

Provides methods to configure the FrequencyRange measurement.

Provides methods to fetch and read the FrequencyRange measurement results.

Represents the ModAcc measurement.

Provides methods to configure the ModAcc measurement.

Provides methods to fetch and read the ModAcc measurement results.

Represents the ModSpectrum measurement.

Provides methods to configure the ModSpectrum measurement.

Provides methods to fetch and read the ModSpectrum measurement results.

Represents the PowerRamp measurement.

Provides methods to configure the PowerRamp measurement.

Provides methods to fetch and read the PowerRamp measurement results.

Represents members that are common to all sub-object of RFmxBTMX classes.

Represents the 20dBBandwidth measurement.

Provides methods to configure the 20dBBandwidth measurement.

Provides methods to fetch and read the 20dBBandwidth measurement results.

Represents the TXP measurement.

Provides methods to configure the TXP measurement.

Provides methods to fetch and read the TXP measurement results.

Specifies whether to enable averaging for the ACP measurement.

Specifies the type of synchronization used for detecting the start of the EDR packet in the adjacent channel power (ACP) measurement.

Specifies which offset channels are used for the measurement.

Indicates the overall measurement status based on the measurement limits specified by the standard when you set the SetOffsetChannelMode(string, RFmxBTMXAcpOffsetChannelMode) method to InBand.

Specifies the format of the Channel Sounding packet depending on the position and presence of SYNC and CS Tone fields. This method is applicable only when you set the SetPacketType(string, RFmxBTMXPacketType) method to LE-CS.

Specifies the type of sequence present in the SYNC portion after trailer bits. This method is applicable only when you set the SetPacketType(string, RFmxBTMXPacketType) method to LE-CS and the SetChannelSoundingPacketFormat(string, RFmxBTMXChannelSoundingPacketFormat) method to any value other than CS Tone.

Specifies whether the tone extension slot transmission is enabled after CS Tone. This method is applicable only when you set the SetPacketType(string, RFmxBTMXPacketType) method to LE-CS and the SetChannelSoundingPacketFormat(string, RFmxBTMXChannelSoundingPacketFormat) method to any value other than SYNC.

Specifies the active edge for the trigger. This method is valid only when you set the SetTriggerType(string, RFmxBTMXTriggerType) method to DigitalEdge.

Specifies the mode of direction finding.

Specifies whether to enable averaging for the FrequencyRange measurement.

Specifies the Higher Data Throughput (HDT) packet format. This method is applicable only when you set the SetPacketType(string, RFmxBTMXPacketType) method to PacketTypeLEHdt.

Specifies the reference for the SetIQPowerEdgeTriggerLevel(string, double) method. The IQ Power Edge Level Type method is used only when you set the SetTriggerType(string, RFmxBTMXTriggerType) method to IQPowerEdge.

Specifies whether the device asserts the trigger when the signal power is rising or when it is falling. The device asserts the trigger when the signal power exceeds the specified level with the slope you specify. This method is used only when you set the SetTriggerType(string, RFmxBTMXTriggerType) method to IQPowerEdge.

Specifies the set of properties that are considered by RFmx in the locked signal configuration state. If your test system performs the same measurement at at different selected ports, multiple frequencies and/or power levels repeatedly, enabling this method can help achieve faster measurements. When you set this method to a value other than Disabled, the RFmx driver will use an optimized code path and skip some checks. Because RFmx skips some checks when you use this method, you need to be aware of the limitations of this feature, which are listed in the Limitations of the Limited Configuration Change Property topic.

Specifies the type of measurement.

Specifies whether to enable averaging for the ModAcc measurements.

Specifies the type of synchronization used for detecting the start of packet in ModAcc measurement.

Specifies whether to enable the I/Q origin offset correction for EDR packets. If you set this method to True, the DEVM results are computed after correcting for the I/Q origin offset.

Specifies whether to enable averaging for ModSpectrum measurements.

Specifies the type of synchronization used for detecting the start of packet in the ModSpectrum measurement.

Specifies the type of the Bluetooth packet to be measured.

Specifies the bit pattern present in the payload of the packet. This value is used to determine the set of ModAcc measurements to be performed.

Specifies the payload length mode of the signal to be measured. The payload length mode and SetPayloadLength(string, int) properties decide the length of the payload to be used for measurement.

Specifies whether to enable averaging for PowerRamp measurement.

Specifies the type of synchronization used for detecting the start of packet in the PowerRamp measurement.

Specifies all the attribute identifiers.

Specifies the standard.

Specifies whether the measurement computes the minimum quiet time used for triggering.

Specifies the type of trigger to be used for signal acquisition.

Specifies whether to enable averaging for the 20dBBandwidth measurement.

Specifies whether to enable averaging for the transmit power (TxP) measurements.

Specifies the type of synchronization used for detecting the start of packet in the transmit power (TXP) measurement.