NI-RFmx TD-SCDMA 2.0 Readme

October 2015

Thank you for using NI-RFmx TD-SCDMA. This file contains important information about NI-RFmx TD-SCDMA and is organized into the following sections:


Installation Instructions

Supported Hardware

System Requirements

Installed Software, Documentation, and Examples

Executable

Documentation

Accessing VIs and Functions

Finding Examples

Product Security and Critical Updates

Uninstalling/Modifying NI-RFmx TD-SCDMA

Known Issues

Increasing Available Memory For Your Application

Automating the Installation of NI Products

Using NI Software with Microsoft Windows 10

Using NI Software with Microsoft Windows 8.x

Legal Information


Installation Instructions

Caution  Before you install NI-RFmx TD-SCDMA 2.0, ensure that you have uninstalled all related NI-RFmx 1.0 products.


NI-RFmx drivers require that all the installed drivers have the same version for proper functionality because the NI-RFmx drivers use shared components that need to use the same version across all drivers. If driver incompatibilities exist, they are reported through a dialog box after installation. You can also use the Version Compatibility Checker utility to manually check for version incompatibilities. Refer to the Installed Software, Documentation, and Examples section for more information about the installed location of the Version Compatibility Checker utility.


Supported Hardware

Vector Signal Analyzers

  • NI PXIe-5663
  • NI PXIe-5663E
  • NI PXIe-5665
  • NI PXIe-5668R

Device-specific information about these modules is included in the NI RF Vector Signal Analyzers Help.


Vector Signal Transceivers

  • NI PXIe-5644R
  • NI PXIe-5645R
  • NI PXIe-5646R

Device-specific information about these modules is included in the NI RF Vector Signal Transceivers Help.


System Requirements

Supported Operating Systems

NI-RFmx TD-SCDMA 2.0 supports the following operating systems:


  • Windows 10 (32-bit and 64-bit)
  • Windows 8.1 (32-bit and 64-bit)
  • Windows 8.0 (32-bit and 64-bit)
  • Windows 7 (32-bit and 64-bit)
  • Windows Server 2008 R2 (64-bit)

Note  NI-RFmx TD-SCDMA 2.0 does not support Windows Server non-R2 editions.


NI recommends that you have the most recent service pack for your operating system installed.


Minimum System Requirements

  • Processor—Intel i3 or equivalent
  • RAM—2 GB*
  • Microsoft Internet Explorer 5.5 or later
  • A screen resolution of 1,300 x 700 with 256 colors
  • Windows 10/8.1/8.0/7, with all available critical updates and service packs

*Depending on the amount of data acquired and/or processed, a larger amount of memory may be required.


Recommended System

  • Processor—Intel i5 or equivalent
  • RAM—4 GB*
  • Microsoft Internet Explorer 5.5 or later
  • A screen resolution of 1,300 x 700
  • Windows 10/8.1/8.0/7, with all available critical updates and service packs
*Depending on the amount of data acquired and/or processed, a larger amount of memory may be required.

Application Development Environments (ADEs)

  • NI LabVIEW 2013 SP1 (32-bit and 64-bit) f6 patch, 2014 SP1 (32-bit and 64-bit) f3 patch, 2015 (32-bit and 64-bit) f1 patch

Note  NI-RFmx TD-SCDMA does not operate correctly without the LabVIEW service packs and patches in the preceding list.


Note  Install NI LabVIEW before you install NI-RFmx TD-SCDMA. To add support for ADEs that are installed after you install NI-RFmx TD-SCDMA, modify your NI-RFmx TD-SCDMA installation or relaunch the NI-RFmx TD-SCDMA installer.


Other Required Software

  • NI-RFSA 14.1 or later

Installed Software, Documentation, and Examples

  • <NIDir> is an alias for the following National Instruments file folder location:
    • Windows 10 (32-bit)/8.1 (32-bit)/8.0 (32-bit)/7 (32-bit): Program Files\National Instruments
    • Windows 10 (64-bit)/8.1 (64-bit) /8.0 (64-bit)/7 (64-bit): Program Files (x86)\National Instruments
  • <SYSDIR> is an alias for the following file folder location:
    • Windows 10 (32-bit)/8.1 (32-bit)/8.0 (32-bit)/7 (32-bit): windows\system32
    • Windows 10 (64-bit)/8.1 (64-bit) /8.0 (64-bit)/7 (64-bit)
      • 32-bit DLL: windows\SysWow64
      • 64-bit DLL: windows\system32

File Locations

Item Installed Location on Windows 10/8.1/8.0/7
Version Compatibility Checker <NIDir>\RFmx\niRFmxCompatibility_Checker.exe
DLLs <SYSDIR>
LabVIEW Examples <NIDir>\LabVIEW <version>\examples\RFmx\TD-SCDMA

Executable

Select Start»All Programs»National Instruments»NI-RFmx TD-SCDMA»NI-RFmx TD-SCDMA Measurement Interactive Panel to launch the NI-RFmx TD-SCDMA Measurement Interactive Panel.


Documentation

Documentation for NI-RFmx TD-SCDMA is located at Start»All Programs»National Instruments»NI-RFmx TD-SCDMA»NI-RFmx TD-SCDMA Documentation. The documentation set is composed of the following documents.


Document Format Description
NI-RFmx TD-SCDMA Help HTML/Windows Help Information about NI-RFmx TD-SCDMA. This help file is an HTML version of a traditional user manual that includes the following information:
  • An introduction to NI-RFmx TD-SCDMA
  • How to get started with application development
  • A complete reference for all NI-RFmx TD-SCDMA programming functions
NI-RFmx TD-SCDMA 2.0 Readme HTML (this document) Information about supported hardware, supported operating systems, and legal notices.

For the most recent revisions of documentation and for newly released documentation, visit ni.com/manuals.


Accessing VIs and Functions

NI-RFmx TD-SCDMA palette VIs are available from the Functions»Measurement I/O»NI-RFmx»TD-SCDMA palette.


Finding Examples

You can access all the installed NI-RFmx TD-SCDMA examples at Start»All Programs»National Instruments»NI-RFmx TD-SCDMA»NI-RFmx TD-SCDMA Examples.


Product Security and Critical Updates

Visit ni.com/security to view and subscribe to receive security notifications about National Instruments products. Visit ni.com/critical-updates for information about critical updates from National Instruments.


Uninstalling/Modifying NI-RFmx TD-SCDMA

For Windows 7, complete the following steps:


  1. Launch the Control Panel by selecting Start»Control Panel.
  2. Double-click Programs and Features.
  3. Select National Instruments Software.
  4. Click the Uninstall/Change button.
  5. Select NI-RFmx TD-SCDMA 2.0 from the dialog box that appears.
  6. Click Remove to uninstall the product; click Modify to change the components that are installed.

For Windows 10/8.1/8.0, complete the following steps:


  1. Right-click on the Start screen.
  2. Select All apps, and launch the Control Panel.
  3. Select Programs»Programs and Features.
  4. Select National Instruments Software.
  5. Click the Uninstall button.
  6. Select NI-RFmx TD-SCDMA 2.0 from the dialog box that appears.
  7. Click Remove to uninstall the product; click Modify to change the components that are installed.

As part of the NI-RFmx TD-SCDMA 2.0 installation, the following software is installed. To completely remove the NI-RFmx TD-SCDMA 2.0 installation from your system, you must also remove the following package:


  • NI-RFmx TD-SCDMA Runtime 2.0 for LabVIEW

Note  Do not attempt to uninstall by manually deleting files.


Known Issues

You can access the software and documentation known issues list online. Refer to the NI-RFmx TD-SCDMA 2.0 Known Issues at ni.com for an up-to-date list of known issues in NI-RFmx TD-SCDMA 2.0.


Increasing Available Memory For Your Application

When developing memory intensive applications, you may encounter memory limits because 32-bit Windows applications utilize only 2 GB of memory by default. To expand the amount of memory an application can utilize, you can configure the executable to be large address aware to gain access to up to 3 GB of memory on a 32-bit Windows operating system and up to 4 GB of memory on a 64-bit Windows operating system.

For more information, refer to Memory Limits for Windows and Windows Server Releases on the Microsoft website.


Note  LabVIEW 8.5 and later are large address aware. For more information about LabVIEW memory usage, refer to KB 2HDEH9DT, How Much Memory can LabVIEW 32-bit or 64-bit Use?.

In TestStand 2013 and later, the Large Address Aware flag is enabled by default for the TestStand Sequence Editor and TestStand User Interfaces. For more information, refer to KB 5ZREUK2G, Using the Large Address Aware Flag With TestStand Applications.

Automating the Installation of NI Products

You can automate the installation of most NI products using command-line arguments to suppress some or all of the installer user interface and dialog boxes. However, starting with the August 2012 releases (products using NI Installers version 3.1 or later), you may need to perform additional steps before or during a silent installation of NI software.


If the NI product you are installing uses Microsoft .NET 4.0, the .NET installer may run before any NI software installs and may require a reboot before the installation of NI software begins. To avoid a .NET reboot, install .NET 4.0 separately before you install NI software.


For more information about automating the installation of NI products, refer to the following KnowledgeBase articles:


Using NI Software with Microsoft Windows 10

Microsoft Windows 10 is the latest version of the Windows operating system and features significant changes compared to previous versions. Windows 10 introduces several new capabilities and also combines features from both Windows 7 and Windows 8. For more information about NI support for Windows 10, visit ni.com/windows10.


Using NI Software with Microsoft Windows 8.x

When you install National Instruments software on Microsoft Windows 8.x, you will notice a few additional tiles in the Apps view, including shortcuts to NI application software products such as NI LabVIEW, Measurement & Automation Explorer (NI MAX), and NI Launcher.


Using NI Launcher

NI Launcher helps you find and launch installed NI products. It provides you with a method of finding NI products similar to the Start menu in previous versions of Microsoft Windows. To use NI Launcher, click the NI Launcher tile in the Apps view. NI Launcher launches the desktop and opens a menu containing a list of NI products. Click any NI product to launch it.


Note  NI MAX does not appear as a desktop shortcut when installed on Microsoft Windows 8.x. You can launch NI MAX either from the Apps view or from within NI Launcher.

Pinning Frequently Used Applications

For convenience, you can pin your most-used NI applications, such as MAX, to either the Start screen or the Taskbar on the desktop, as necessary.


Current Application Icon Location Pin to Action
Windows 8.x Desktop Desktop Taskbar Right-click application and select Pin to Taskbar
Windows 8.x Desktop Start screen Right-click application and select Pin to Start
Windows 8.x Start screen Desktop Taskbar Right-click application and select Pin to taskbar from the menu bar on the bottom of the screen

Finding All Programs

If you want to find a particular application or related files, such as documentation files, from the Start screen, you can access all installed files from the Apps view. To get to the Apps view, right-click anywhere on the Start screen and select All apps (Windows 8) or click the down arrow on the bottom left of the screen (Windows 8.1).


For more information about NI support for Windows 8.x, visit ni.com/windows8.



Legal Information

Copyright


© 2015 National Instruments. All rights reserved.


Under the copyright laws, this publication may not be reproduced or transmitted in any form, electronic or mechanical, including photocopying, recording, storing in an information retrieval system, or translating, in whole or in part, without the prior written consent of National Instruments Corporation.


National Instruments respects the intellectual property of others, and we ask our users to do the same. NI software is protected by copyright and other intellectual property laws. Where NI software may be used to reproduce software or other materials belonging to others, you may use NI software only to reproduce materials that you may reproduce in accordance with the terms of any applicable license or other legal restriction.


End-User License Agreements and Third-Party Legal Notices


You can find end-user license agreements (EULAs) and third-party legal notices in the following locations after installation:


  • Notices are located in the <National Instruments>\_Legal Information and <National Instruments> directories.
  • EULAs are located in the <National Instruments>\Shared\MDF\Legal\license directory.
  • Review <National Instruments>\_Legal Information.txt for information on including legal information in installers built with NI products.

U.S. Government Restricted Rights


If you are an agency, department, or other entity of the United States Government ("Government"), the use, duplication, reproduction, release, modification, disclosure or transfer of the technical data included in this manual is governed by the Restricted Rights provisions under Federal Acquisition Regulation 52.227-14 for civilian agencies and Defense Federal Acquisition Regulation Supplement Section 252.227-7014 and 252.227-7015 for military agencies.


IVI Foundation Copyright Notice


Content from the IVI specifications reproduced with permission from the IVI Foundation.


The IVI Foundation and its member companies make no warranty of any kind with regard to this material, including, but not limited to, the implied warranties of merchantability and fitness for a particular purpose. The IVI Foundation and its member companies shall not be liable for errors contained herein or for incidental or consequential damages in connection with the furnishing, performance, or use of this material.


Trademarks


Refer to the NI Trademarks and Logo Guidelines at ni.com/trademarks for information on National Instruments trademarks. Other product and company names mentioned herein are trademarks or trade names of their respective companies.


Patents


For patents covering the National Instruments products/technology, refer to the appropriate location: Help»Patents in your software, the patents.txt file on your media, or the National Instruments Patent Notice at ni.com/patents.


375525A-01