NI-mmWave 15.1 Known Issues

Overview

This document contains the NI-mmWave 15.1 known issues that were discovered before and since the release of NI-mmWave 15.1. Not every issue known to NI appears on this list; it is intended to show the most severe and common issues that can be encountered.

Each issue appears as a row in the table and includes the following fields:

  • Issue ID - The number in at the top of each of the cells in the first column. When you report an issue to NI, you may be given this ID, you can also find IDs posted by NI on the discussion forums or in Knowledge Base articles.  "N/A" indicates that there is no ID assigned to the issue.
  • Issue Title (in italics) - Describes the issue in one sentence or less.
  • Problem Description - A few sentences which describe the problem in further detail. The brief description given does not necessarily describe the problem in full detail, and it is expected that you may want more information on an issue. If you would like more information on an issue, contact NI and reference the ID number given in the document.
  • Workaround - Possible ways to work around the problem. The workarounds that appear in the document are not always tested by NI and are not guaranteed to resolve the issue. If a workaround refers you to the NI KnowledgeBase, visit www.ni.com/kb/ and enter the KnowledgeBase number in the search field to locate the specific document.
  • Reported Version - The earliest version of NI-mmWave in which the issue was reported. If you discover the issue appears in an earlier version of NI mmWave than is reported in this field, report the discrepancy to NI to have the field updated.
  • Resolved Version - Version in which the issue was resolved or was no longer applicable. "N/A" indicates that the issue has not been resolved.
  • Date Added - The date the issue was added to the document (not the reported date).

Known Issues

601381 Sample Clock on PXIe-7902R not enabled after reboot.
600897 Installation error when upgrading NI Linux Real-Time Support for NI mmWave devices.
583667 Incorrectly reports coerced value for out-of-bounds frequencies when using external LO.
582873 PXIe-3620 session invalid after aborting session.
582362 Putting OS into Sleep state while NI mmWave session is open results in error -63150, -52007.
582132 Gain ranging takes 4x (2x) longer than typical on first (second) instruction when using PXIe-1075 chassis.
580686 MAX exposes unsupported features for PXIe-7902R.


ID Known Issue
601381

Return
Sample Clock on PXIe-7902R not enabled after reboot.
External FPGA clocks, including the Sample Clock(s), are not maintained when the system is rebooted without being powered down. Re-downloading the relevant bitfiles will re-sync these clocks. If the force download flag is not set to TRUE, the TX Open VI and the RX Open VI will error out when attempting to open a new session because bitfiles are not downloaded automatically after a soft reset.

Workaround: Ensure the force download flag is set to TRUE (default) on Open VI.

Reported Version: 15.1    Resolved Version: N/A    Added: 09/16/16
600897

Return
Installation error occurs when upgrading NI Linux Real-Time Support for NI mmWave devices.
When upgrading the support from NI mmWave 15.0 to NI mmWave 15.1, the target will enter a bad and unrecoverable state. The only way to recover from this state is to reformat the RT target.

Workaround: To upgrade NI mmWave support on a Linux Real-Time Target that already has NI mmWave 15.0 installed, complete the following steps:
  1. Open MAX and run the Add/Remove Software wizard on the Linux Real-Time target.
  2. Uninstall all NI mmWave devices support by selecting "Uninstall the feature" for the following items: NI PXIe 7902R NI Linux Real-Time Support, NI PXIe-3610/3630 NI Linux Real-Time Support, and NI PXIe-3620 NI Linux Real-Time Support.
  3. After the uninstallation is finished, you can install NI mmWave 15.1.

Reported Version: 15.1    Resolved Version: 15.3    Added: 09/16/16
583667

Return
NI mmWave incorrectly reports coerced value for out-of-bounds frequencies when using external LO.
When using an external LO, the NI mmWave driver will coerce out-of-bounds frequency values specified by the user to be within the normal operating range of the hardware. The external source is not affected, but the value used for internal calculations and reported to the user will not accurately reflect the value of this source.

Workaround: Using an external source outside the frequency ranges typically supported by NI mmWave hardware is not a valid configuration and will result in unexpected system behavior. Tune any external LO source to be within the range specified on the front panel terminal to which it is connected, and supply accurate frequency values for this source to the driver during configuration.

Reported Version: 15.0    Resolved Version: 15.3    Added: 09/16/16
582873

Return
PXIe-3620 session invalid after aborting session.
The PXIe-3620 hardware may enter an unknown state if the session is forcibly closed by aborting a VI, ending the process, or any other method that terminates device communication without calling Close Session VI.

Workaround: Always end the PXIe-3620 session by calling mmWave Close Session VI.

To recover after this failure, power down the system completely and reboot.

Reported Version: 15.0    Resolved Version: 15.3    Added: 09/16/16
582362

Return
Putting OS into sleep state while NI mmWave session is open results in error -63150, -52007.
NI mmWave does not support sleep mode. If a Windows system is put into a sleep state while an NI mmWave session is open and actively running, the hardware will enter an invalid state. After waking the system. attempting to open a new session to the PXIe-3620 or PXIe-7902R hardware will result in error -63150 (operation failed) or -52007 (operation timeout).

Workaround: Disable Windows power management modes, such as sleep, standby, and hibernate, when using this product.

To recover after this error, completely power down and reboot the system to return it to a known state.

Reported Version: 15.0    Resolved Version: N/A    Added: 09/16/16
582132

Return
Gain ranging takes 4x (2x) longer than typical on first (second) instruction when using PXIe-1075 chassis.
When using NI-P2P to send gain ranging instructions to an NI mmWave device in a PXIe-1075 chassis, the first instruction sent after linking the sender and recipient takes four times the configured dwell time. The second instruction takes twice the configured dwell time. Instructions after this adhere to the dwell time.

Workaround: Use a PXIe-1085 chassis. If a PXIe-1075 chassis must be used, and settling time for the first set of instructions is critical, link and send multiple instructions prior to beginning acquisition/generation.

Reported Version: 15.0    Resolved Version: N/A    Added: 09/16/16
580686

Return
MAX exposes unsupported features for PXIe-7902R.
The settings page in MAX provides the following three configurable options that are not actually supported on the PXIe-7902R: Firmware Autoload Setting, Update Firmware, and Erase Firmware.

Workaround: These options are not supported. Do not try to perform these actions.

Reported Version: 15.0    Resolved Version: 15.3    Added: 09/16/16

Contacting NI

Contact NI regarding this document or issues in the document. If you contact NI in regards to a specific issue, reference the ID number given in the document. The ID number contains the current issue ID number as well as the legacy ID number (use the current ID number when contacting NI). You can contact us through any of the normal support channels including phone, email, or the discussion forums. Visit the NI Website to contact us. Also contact us if you find a workaround for an issue that is not listed in the document.

Glossary of Terms

 

  • Bug ID - When an issue is reported to NI, you may be given this ID or find it on ni.com.  You may also find IDs posted by NI on the discussion forums or in KnowledgeBase articles.
  • Legacy ID – An older issue ID that refers to the same issue.  You may instead find this issue ID in older known issues documents.
  • Description - A few sentences which describe the problem. The brief description given does not necessarily describe the problem in full detail.
  • Workaround - Possible ways to work around the problem.
  • Reported Version - The earliest version in which the issue was reported.
  • Resolved Version - Version in which the issue was resolved or was no longer applicable. "N/A" indicates that the issue has not been resolved.
  • Date Added - The date the issue was added to the document (not the reported date).