RFmxLTE SEM Configure Uplink Mask Type (VI)

Download PDF

Updated2024-04-10
4 minute(s) read

Owning Palette: SEM

Configures the standard defined mask type that has to be used in the measurement for uplink.

RFmxLTE SEM Configure Uplink Mask Type

Instrument Handle In specifies the RFmx session refnum. Instrument Handle In is obtained from the RFmxInstr Initialize NIRFSA VI.

Uplink Mask Type specifies the standard-defined spectrum emission mask used in the measurement for uplink. The following mask types are supported: General (NS_01), NS_03 or NS_11 or NS_20 or NS_21, NS_04, NS_06 or NS_07, CA_NS_04, Custom, General CA Class B, CA_NC_NS_01, NS_27, and NS_35. Each mask type refers to a different Network Signalled (NS) value. CA_NS_04 and CA_NC_NS_01 refers to carrier aggregation case. You must set the mask type to CUSTOM to configure the custom offset masks. Refer to section 6.6.2.1 of the 3GPP 36.521 specification for more information about standard-defined mask types.

General (NS_01) (0)

The measurement selects the offset frequencies and limits for the SEM as defined in Table 6.6.2.1.5-1, 6.6.2.1.5-2, 6.6.2.1A.5-1, and 6.6.2.1A.5-2 in section 6.6.2 of the 3GPP TS 36.521-1 specification.

NS_03 or NS_11 or NS_20 or NS_21 (1)

The measurement selects the offset frequencies and limits for the SEM as defined in Table 6.6.2.2.5.1-1 and 6.6.2.2.5.1-2 in section 6.6.2 of the 3GPP TS 36.521-1 specification.

NS_04 (2)

The measurement selects the offset frequencies and limits for the SEM as defined in Table 6.6.2.2.3.2-3 in section 6.6.2 of the 3GPP TS 36.521-1 specification.

Note When CC Bandwidth is 1.4 M or 3.0 M, the measurement selects the offset frequencies and limits for the SEM as defined in Table 6.6.2.2.5.2-1 in section 6.6.2 of the 3GPP TS 36.521-1 specification.

NS_06 or NS_07 (3)

The measurement selects the offset frequencies and limits for the SEM as defined in Table 6.6.2.2.5.3-1 and 6.6.2.2.5.3-2 in section 6.6.2 of the 3GPP TS 36.521-1 specification.

CA_NS_04 (4)

The measurement selects the offset frequencies and limits for the SEM as defined in Table 6.6.2.2A.1.5.1-1 in section 6.6.2 of the 3GPP TS 36.521-1 specification. This mask applies only for aggregated carriers.

Custom (5)

You need to configure the SEM Num Offsets, SEM Offset Start Freq, SEM Offset Stop Freq, SEM Offset Abs Limit Start, SEM Offset Abs Limit Stop, SEM Offset Sideband, SEM Offset RBW, SEM Offset RBW Filter Type, and SEM Offset BW Integral properties for each offset.

General CA Class B (6)

The measurement selects offset frequencies and limits for the SEM as defined in Table 6.6.2.1A.1.5-3 and 6.6.2.1A.1.5-4 in section 6.6.2 of 3GPP TS 36.521-1 specification.

CA_NC_NS_01 (7)

The measurement selects offset frequencies and limits for the SEM as defined in Table 6.6.2.2A.3.5-1 and 6.6.2.2A.3.5-2 in section 6.6.2 of 3GPP TS 36.521-1 specification.

NS_27 (8)

The measurement selects offset frequencies and limits for the SEM as defined in Table 6.6.2.2.5.4-1 in section 6.6.2.2.5.4 of 3GPP TS 36.521-1 specification.

NS_35 (9)

The measurement selects offset frequencies and limits for the SEM as defined in Table 6.6.2.2.5.5-1 in section 6.6.2.2.5.5 of 3GPP TS 36.521-1 specification.

Selector String specifies a selector string comprising of the signal name. If you do not specify the signal name, the default signal instance is used. The default is "" (empty string).

Example:

"signal::sig1"

You can use the RFmxLTE Build Signal String VI to build the selector string.

error in describes error conditions that occur before this node runs. This input provides standard error in functionality.

Instrument Handle Out passes a reference to your RFmx session to the next VI.

error out contains error information. This output provides standard error out functionality.

RFmx LTE VIs

Table of Contents

RFmxLTE SEM Configure Uplink Mask Type (VI)

Log in to get a better experience