Filtered Results

In your Logging specification document, specify values for the Operator and DUT in the Test Properties section, if desired. The fields for Operator and DUT are auto-populated, but can be changed or deleted, ...

Before adding CAN and LIN signals to your Channel Specification, you may need to create or manage the databases that provide the signal definitions and scaling information for your application. Refer to ...

CAN interfaces are software representations of physical ports. Complete the following steps to adjust the port settings. Enable Termination, if necessary. Improperly configured Termination schemes might ...

Click Add Signals on the CAN port you want to configure. Select the Database that contains the signals you want to update. Select the Cluster that contains the signals you want to apply J1939 to. Select ...

Although it is possible (and supported) in principle to run a network without a database, using a database is highly recommended to have a consistent set of network parameters for all nodes in the network. ...

Hover over the channel row to see the Configure gear . Click the gear for the channel you wish to configure. The channel configuration dialog opens. Use the Name field to specify the channel name, if necessary. ...

Add a calculated Boolean channel to produce a high or low Boolean digital signal based on an analog channel. In the Channel Specification, click the Add Calculation button and select Boolean Formula from ...

Hover over the channel row to see the Configure gear . Click the gear for the channel you wish to configure. The channel configuration dialog opens. Use the Name field to specify the channel name, if necessary. ...

Refer to the following information to configure your device channels. Configuring I/O Channels Configuring an Automotive Bus Configuring Calculated Channels After you configure your channels, you can start ...

Add a channel produced by applying either a lowpass or a highpass Butterworth filter to an existing hardware channel. The lowpass or highpass filter channel displays filtered data that excludes any noise ...

Add and configure signals to use in your Channel specification. Use any of the following options that apply to the devices in your system: Configure sensors in your Channel Specification Configure digital ...

Add a channel that applies RMS or Mean averaging to the data in an existing hardware channel. The RMS or Mean channel produces a new value based on averaging performed on the data in a channel in the system. ...

Hover over the channel row to see the Configure gear . Click the gear for the channel you wish to configure. The channel configuration dialog opens. Use the Name field to specify the channel name, if necessary. ...

Low-Speed CAN requires termination at the Low-Speed CAN transceiver instead of on the cable. The termination requires two resistors: RTH for CAN_H and RTL for CAN_L. This configuration allows the NXP fault-tolerant ...

FlexLogger automatically discovers any installed hardware and displays it in the Channel Specification. Available device channels will be listed beneath the module information. CompactDAQ modules will ...

In your Logging specification document, select a Start condition for your trigger. Selecting any Triggering conditions will enable the trigger. Select from the following trigger start conditions: Test ...

To begin interacting with your measurement system and creating logging and automated test configurations, create a new project in one of the following ways: Create a Data Logging Project from the launcher. ...

You must set up the necessary sensors in your measurement system to log data. Configure the logging specification for your log files. Enable and configure triggers for your acquisition. Adding Metadata ...

Go to File Manage CAN/LIN databases . Use the dialog that appears to add, remove, or rename your available databases. Double-click any database to launch the CAN/LIN Database Editor. The CAN/LIN Database ...

Complete the following steps to apply scaling to your configured sensor. Click the Configure gear on the channel of the device you wish to scale. The channel configuration dialog opens. In the Scaling ...

You can set output channels to their Reset Value by creating an event and using the Reset output channels action. Hover over the channel row to see the Configure gear . Click the gear for the channel you ...

If you are having trouble finding your hardware in the FlexLogger Channel Specification, try the following tips. Refer to the list of supported hardware to confirm that your devices are supported in FlexLogger. ...

You must have channels added and configured for your FlexLogger project in order to visualize data from your sensor signals. Refer to the Configuring Device Channels topic for more information. Map your ...

Hover over the channel row to see the Configure gear . Click the gear for the channel you wish to add an alarm to. Select the Alarms tab in the Channel Configuration dialog. Specify one of the following ...

In your Test Specification document, click the Add Event button. The Configure Event dialog opens. Create the If condition that will trigger the event. Channel value change Click the Select channel button ...

Each LED can display two colors (red or green), which display in the following four patterns: Pattern Meaning Off No LED illumination Solid LED fully illuminated Blink Blinks at a constant rate of several ...

Open or create a FlexLogger Project. Find the hardware devices in your system. Configure Device Channels for data acquisition or signal generation.

FlexLogger supports both hardware and software filters for use in your project. Hardware filters offer a variety of filter type options to provide anti-aliasing and noise reduction with no CPU usage or ...

Hover over the channel row to see the Configure gear . Click the gear for the channel you wish to add a strain gage to. Select the desired Bridge Configuration. Specify the Bridge Resistance (if available), ...

Use these methods to set the history length for High Speed Graphs and Long History Graphs. Set the Default History Length Go to FilePreferences and specify your High speed history length or Long history ...

Showing 1-30 of 65 results
1 of 3 pages