Filtered Results

Indicates the serial number of the device carrier. This value is zero if the carrier does not have a serial number. Not supported Not supported in VIs that run in a web application 2A8A attr2A8A.html

Indicates an array containing the names of the modules in the chassis. Not supported Not supported in VIs that run in a web application 29B6 attr29B6.html

Indicates in bits the size of the counters on the device. Not supported Not supported in VIs that run in a web application 299F attr299F.html

Writes data from a virtual TEDS file to the TEDS sensor. LabVIEW NXG does not support FPGA devices Not supported in VIs that run in a web application DAQmx Write TEDS Data (TEDS Data File).vi :/lvdaqmx.chm::/DAQmx ...

Indicates the measurement types supported by the physical channels of the device. Refer to CI.MeasTypes for information on specific channels. Not supported Not supported in VIs that run in a web application ...

Indicates an array containing the names of the counter input physical channels available on the device. Not supported Not supported in VIs that run in a web application 2324 attr2324.html

Indicates if the device supports the sample clock timing type for counter input tasks. Not supported Not supported in VIs that run in a web application 299E attr299E.html

Indicates sample modes supported by devices that support sample clocked counter input. Not supported Not supported in VIs that run in a web application Finite Samples 10178 Acquire or generate a finite ...

Indicates the maximum digital output rate of the device. Not supported Not supported in VIs that run in a web application 299A attr299A.html

Indicates an array containing the names of the digital output ports available on the device. Not supported Not supported in VIs that run in a web application 2323 attr2323.html

Indicates the PCI bus number of the device. Not supported Not supported in VIs that run in a web application 2327 attr2327.html

Specifies whether to turn on the sensor's power supply or to leave the configuration unchanged. Not supported Not supported in VIs that run in a web application No Change 10160 Sensor power supply configuration ...

Indicates whether there is an overcurrent condition on the channel. Not supported Not supported in VIs that run in a web application 21D9 attr21D9.html

Specifies the voltage level for the sensor's power supply. Not supported Not supported in VIs that run in a web application 21D9 attr21D9.html

Indicates the unique hardware identification number for accessories connected to the device. Each array element corresponds to a connector. For example, index 0 corresponds to connector 0. The array contains ...

Indicates the major portion of the installed version of NI-DAQmx, such as 7 for version 7.0. Not supported Not supported in VIs that run in a web application 1272 attr1272.html

Indicates the serial number for accessories connected to the device. Each array element corresponds to a connector. For example, index 0 corresponds to connector 0. The array contains 0 for each connector ...

Indicates an array that contains the names of all custom scales saved on the system. Not supported Not supported in VIs that run in a web application 1266 attr1266.html

Indicates an array that contains the names of all tasks saved on the system. Not supported Not supported in VIs that run in a web application 1267 attr1267.html

Specifies whether to enable or disable a channel for amplification. This property can also be used to check if a channel is enabled. Not supported Not supported in VIs that run in a web application 3062 ...

Indicates the calibrated gain of the channel. Not supported Not supported in VIs that run in a web application 3065 attr3065.html

Indicates the calibrated offset of the channel in volts. Not supported Not supported in VIs that run in a web application 3066 attr3066.html

Indicates if any devices in the task detected the insertion or removal of an accessory since the task started. Reading this property clears the accessory change status for all channels in the task. You ...

Specifies the name of a terminal where there is a digital signal to use as the source of the Advance Trigger. Not supported Not supported in VIs that run in a web application 1362 attr1362.html

Specifies the first physical value, corresponding to AI.Bridge.TwoPointLin.First.ElectricalVal. Specify this value in the unit indicated by AI.Bridge.PhysicalUnits. Not supported Not supported in VIs that ...

Specifies the output signal delay in periods of the sample clock. Not supported Not supported in VIs that run in a web application 1757 attr1757.html

Specifies the terminal to which to route the Advance Complete Event. Not supported Not supported in VIs that run in a web application 1651 attr1651.html

Specifies the second physical value, corresponding to AI.Bridge.TwoPointLin.Second.ElectricalVal. Specify this value in the unit indicated by AI.Bridge.PhysicalUnits. Not supported Not supported in VIs ...

Specifies the width of the exported Advance Complete Event pulse. Not supported Not supported in VIs that run in a web application 1654 attr1654.html

Showing 181-210 of 2163 results
7 of 73 pages