Filtered Results

Add and configure signals to use in your Channel specification. Use any of the following options that apply to the devices in your system: Configure sensors in your Channel Specification Configure digital ...

In your Test Specification document, click the Add Event button. The Configure Event dialog opens. Create the If condition that will trigger the event. Channel value change Click the Select channel button ...

Refer to the following information to configure your device channels. Configuring I/O Channels Configuring an Automotive Bus Configuring Calculated Channels After you configure your channels, you can start ...

Complete the following steps to apply scaling to your configured sensor. Click the Configure gear on the channel of the device you wish to scale. The channel configuration dialog opens. In the Scaling ...

Complete the following steps to apply scaling to your configured sensor. Click the Configure gear on the channel of the device you wish to scale. The channel configuration dialog opens. In the Scaling ...

Hover over the channel row to see the Configure gear . Click the gear for the channel you wish to add a strain gage to. Select the desired Bridge Configuration. Specify the Bridge Resistance (if available), ...

Use these methods to set the history length for graphs that support hold and pan viewing control. Set the Default History Length Go to File Preferences and specify the history length for your graph type ...

You can set output channels to their reset value by creating an event and using the Reset output channels action. Hover over a channel row and click the Configure gear for the channel you wish to enable ...

Navigate to the Graphs palette on your Screen.flxscr document. Click the graph you want to use and drag it onto the Screen. Add the channels you want to visualize to the graph as shown in the Mapping an ...

Synchronization-enabled devices use the IEEE 802.1AS protocol over the network and cannot synchronize with devices that use other protocols or IEEE 1588 profiles or vice versa. Ensure that your system ...

Extend the functionality of FlexLogger by adding a custom plugin to your project. What to UseThe FlexLogger Plugin Development Kit guides you through planning, creating, and testing your custom plugins ...

Select one or more channels you wish to add an alarm to. Hover over a channel row to see the Configure gear . Click the gear for the channel you wish to add an alarm to. Select the Alarms tab in the Channel ...

In your Test Specification document, click the Add Event button. The Configure Event dialog opens. Create the If condition that will trigger the event. Channel value change Click the Select channel button ...

You can use test properties as placeholders when you configure your log file name and location. Refer to the Using Test Metadata as Placeholders for Log File Names and Locations topic for more information. ...

Before adding CAN and LIN signals to your Channel Specification, you may need to create or manage the databases that provide the signal definitions and scaling information for your application. Refer to ...

While the test is running, click the Add Note button in the toolbar. A dialog will open, timestamped with the time the button was clicked. Record any information you wish to include in the log file. Note ...

CAN interfaces are software representations of physical ports. Complete the following steps to adjust the port settings. Enable Termination, if necessary. Improperly configured Termination schemes might ...

LIN interfaces are software representations of physical ports. Complete the following steps to adjust the port settings. Enable Termination, if necessary. Improperly configured Termination schemes might ...

Click Add Signals on the CAN port you want to configure. Select the Database that contains the signals you want to update. Select the Cluster that contains the signals you want to apply J1939 to. Select ...

On the Logging Specification document, select Export automatically to CSV file format when logging completes. Specify the CSV file data rate, if necessary. All logged data channels are mapped to a common ...

In your Channel Specification document, select all configured channels you wish to calibrate. In your Channel Specification document toolbar, click the Calibrate channels button . Select one of the following ...

Although it is possible (and supported) in principle to run a network without a database, using a database is highly recommended to have a consistent set of network parameters for all nodes in the network. ...

Specify the base path for the location where your data file will be saved and file name. You can add test properties to a project and use them as placeholders when you specify your data log file name and ...

Select one or more channels you wish to configure. Hover over a channel row and click the Configure gear . The configure gear appears when selecting multiple channels of the same data type (analog, digital, ...

Select one of the following options depending on your automotive network: Use CAN databases—Manage and configure CAN databases to determine which signals to use in your Channel Specification. Use LIN databases—Manage ...

Add counters to a project by configuring signals in the Channel Specification. Use these steps to configure counters for counter modules, such as the NI-9361, and onboard counters by enabling the line ...

You can configure the data rate at which your DAQ device acquires data by customizing the data ranges and setting the values for analog (slow, medium, and fast) and digital data rate levels. For devices ...

Add a channel produced by applying either a lowpass or a highpass Butterworth filter to an existing hardware channel. The lowpass or highpass filter channel displays filtered data that excludes any noise ...

Add a calculated channel to analyze or scale data from existing hardware channels. A calculated channel produces a new value based on calculations performed on other channels in the system. On the Channel ...

Add and configure signals to use in your Channel specification. Use any of the following options that apply to the devices in your system: Configure sensors in your Channel Specification Configure digital ...

Showing 1-30 of 83 results
1 of 3 pages