Filtered Results

Configure your measurement for use in the project by adding signals to the Channel Specification. For information on how to configure signals, refer to the Configuring Device Channels topic. Set up the ...

NI recommends the read rate of 1 Hz for data using SystemLink tags. For channels that require a faster read data rate, consider using the FlexLogger Plugin Development Kit to create a custom LabVIEW plugin ...

Low-Speed CAN requires termination at the Low-Speed CAN transceiver instead of on the cable. The termination requires two resistors: RTH for CAN_H and RTL for CAN_L. This configuration allows the NXP fault-tolerant ...

FlexLogger supports both hardware and software filters for use in your project. Hardware filters offer a variety of filter type options to provide anti-aliasing and noise reduction with no CPU usage or ...

Navigate to the Graphs palette on your Screen.flxscr document. Click the graph you want to use and drag it onto the Screen. Add the channels you want to visualize to the graph as shown in the Mapping an ...

In your Channel Specification document, select all configured channels you wish to calibrate. In your Channel Specification document toolbar, click the Calibrate channels button . Select one of the following ...

Although it is possible (and supported) in principle to run a network without a database, using a database is highly recommended to have a consistent set of network parameters for all nodes in the network. ...

Select one or more channels you wish to configure. Hover over a channel row and click the Configure gear . The configure gear appears when selecting multiple channels of the same data type (analog, digital, ...

Add a calculated Boolean channel to produce a high or low Boolean digital signal based on an analog or digital channel. On the Channel Specification toolbar, select Add channel Calculation Boolean Formula ...

A calculated channel produces a new value based on calculations performed on other channels in the system. You can choose from the following calculation types: Configuring RMS and Mean Channels Configuring ...

Add counters to a project by configuring signals in the Channel Specification. Use these steps to configure counters for counter modules, such as the NI 9361, and onboard counters by enabling the line ...

Refer to the following information to configure your device channels. Configuring I/O Channels Configuring an Automotive Bus Configuring Calculated Channels After you configure your channels, you can start ...

Select one or more channels you wish to configure. Hover over a channel row and click the Configure gear . The configure gear appears when selecting multiple channels of the same data type (analog, digital, ...

Add and configure signals to use in your Channel specification. Use any of the following options that apply to the devices in your system: Configure sensors in your Channel Specification Configure digital ...

Select one or more channels you wish to configure. Hover over a channel row to see the Configure gear . Click the gear for the channel or channels you wish to configure. The configure gear appears when ...

You can view your hardware in the Channel Specification to begin configuring and managing the signals in your system, such as in the following example system: Available device channels are beneath the ...

Each LED can display two colors (red or green), which display in the following four patterns: Pattern Meaning Off No LED illumination Solid LED fully illuminated Blink Blinks at a constant rate of several ...

You must set up the necessary sensors in your measurement system to log data. Configure the logging specification for your log files. Enable and configure triggers for your acquisition. Adding Metadata ...

FlexLogger supports both hardware and software filters for use in your project. Hardware filters offer a variety of filter type options to provide anti-aliasing and noise reduction with no CPU usage or ...

Configure your measurement for use in the project by adding signals to the Channel Specification. For information on how to configure signals, refer to the Configuring Device Channels topic. Set up the ...

Complete the following steps to apply scaling to your configured sensor. Click the Configure gear on the channel of the device you wish to scale. The channel configuration dialog opens. In the Scaling ...

Hover over the channel row to see the Configure gear . Click the gear for the channel you wish to add a strain gage to. Select the desired Bridge Configuration. Specify the Bridge Resistance (if available), ...

On the Data tab, double-click the data log file to launch the DIAdem-based FlexLogger TDMS Viewer. View your data and perform analyses including arithmetic calculations and fast Fourier transforms (FFT) ...

Extend the functionality of FlexLogger by adding a custom plugin to your project. What to UseThe FlexLogger Plugin Development Kit guides you through planning, creating, and testing your custom plugins ...

Select one or more channels you wish to add an alarm to. Hover over a channel row to see the Configure gear . Click the gear for the channel you wish to add an alarm to. Select the Alarms tab in the Channel ...

In your Test Specification document, click the Add Event button. The Configure Event dialog opens. Create the If condition that will trigger the event. Channel value change Click the Select channel button ...

You can use metadata as placeholders when you configure your log file name and location. Refer to the Using Test Metadata as Placeholders for Log File Names and Locations topic for more information. In ...

Before adding CAN and LIN signals to your Channel Specification, you may need to create or manage the databases that provide the signal definitions and scaling information for your application. Refer to ...

While the test is running, click the Add Note button in the toolbar. A dialog will open, timestamped with the time the button was clicked. Record any information you wish to include in the log file. Note ...

CAN interfaces are software representations of physical ports. Complete the following steps to adjust the port settings. Enable Termination, if necessary. Improperly configured Termination schemes might ...

Showing 1-30 of 82 results
1 of 3 pages