Filtered Results

Although it is possible (and supported) in principle to run a network without a database, using a database is highly recommended to have a consistent set of network parameters for all nodes in the network. ...

Add a calculated Boolean channel to produce a high or low Boolean digital signal based on an analog or digital channel. On the Channel Specification toolbar, select Add channel Calculation Boolean Formula ...

Low-Speed CAN requires termination at the Low-Speed CAN transceiver instead of on the cable. The termination requires two resistors: RTH for CAN_H and RTL for CAN_L. This configuration allows the NXP fault-tolerant ...

You can view your hardware in the Channel Specification to begin configuring and managing the signals in your system, such as in the following example system: Available device channels are beneath the ...

Complete the following steps to apply scaling to your configured sensor. Click the Configure gear on the channel of the device you wish to scale. The channel configuration dialog opens. In the Scaling ...

Synchronization-enabled devices use the IEEE 802.1AS protocol over the network and cannot synchronize with devices that use other protocols or IEEE 1588 profiles or vice versa. Ensure that your system ...

FlexLogger supports both hardware and software filters for use in your project. Hardware filters offer a variety of filter type options to provide anti-aliasing and noise reduction with no CPU usage or ...

LIN interfaces are software representations of physical ports. Complete the following steps to adjust the port settings. Enable Termination, if necessary. Improperly configured Termination schemes might ...

Click Add Signals on the CAN port you want to configure. Select the Database that contains the signals you want to update. Select the Cluster that contains the signals you want to apply J1939 to. Select ...

Select one or more channels you wish to configure. Hover over a channel row to see the Configure gear . Click the gear for the channel or channels you wish to configure. The configure gear appears when ...

A calculated channel produces a new value based on calculations performed on other channels in the system. You can choose from the following calculation types: Configuring RMS and Mean Channels Configuring ...

Select one or more channels you wish to add an alarm to. Hover over a channel row to see the Configure gear . Click the gear for the channel you wish to add an alarm to. Select the Alarms tab in the Channel ...

Select one or more channels you wish to configure. Hover over a channel row to see the Configure gear . Click the gear for the channel or channels you wish to configure. The configure gear appears when ...

Before adding CAN and LIN signals to your Channel Specification, you may need to create or manage the databases that provide the signal definitions and scaling information for your application. Refer to ...

Add a calculated channel to analyze or scale data from existing hardware channels. A calculated channel produces a new value based on calculations performed on other channels in the system. On the Channel ...

Add a channel that applies RMS or Mean averaging to the data in an existing hardware channel. The RMS or Mean channel produces a new value based on averaging performed on the data in a channel in the system. ...

Depending on your application, you can set any of the following configurations for your project: Logging Data Adding Metadata to a Project Enabling and Configuring Triggers Adding an Event

To begin interacting with your measurement system and creating logging and automated test configurations, create a new project in one of the following ways: Create a Data Logging Project from the launcher. ...

If there's a way we could shorten/condense this example, I can see a case for leaving it in this topic. But it's so much longer than the steps themselves the way it is now, which makes the topic less focused. ...

Each LED can display two colors (red or green), which display in the following four patterns: Pattern Meaning Off No LED illumination Solid LED fully illuminated Blink Blinks at a constant rate of several ...

Go to File Manage CAN/LIN databases . Use the dialog that appears to add, remove, or rename your available databases. Double-click any database to launch the CAN/LIN Database Editor. The CAN/LIN Database ...

You must have channels added and configured for your FlexLogger project in order to visualize data from your sensor signals. Refer to the Configuring Device Channels topic for more information. On the ...

Configure your measurement for use in the project by adding signals to the Channel Specification. For information on how to configure signals, refer to the Configuring Device Channels topic. Set up the ...

Complete the following steps to apply scaling to your configured sensor. Click the Configure gear on the channel of the device you wish to scale. The channel configuration dialog opens. In the Scaling ...

You can set output channels to their Reset Value by creating an event and using the Reset output channels action. Hover over the channel row to see the Configure gear . Click the gear for the channel you ...

Navigate to the Graphs palette on your Screen.flxscr document. Click the graph you want to use and drag it onto the Screen. Add the channels you want to visualize to the graph as shown in the Mapping an ...

Synchronization-enabled devices use the IEEE 802.1AS protocol over the network and cannot synchronize with devices that use other protocols or IEEE 1588 profiles or vice versa. Ensure that your system ...

On the Data tab, right-click any log file and select Locate in Windows Explorer. Right-click the TDMS log file you want to open and select Open with»Excel Importer.

On the Data tab, double-click the data log file to launch the DIAdem-based FlexLogger TDMS Viewer. If you have a separately licensed version of DIAdem installed, you can configure FlexLogger to launch ...

FlexLogger includes the following graph types: Graph Type Description High-Speed Graph Visualize larger amounts of data over short time periods. Long History Graph Visualize data over extended time periods. ...

Showing 1-30 of 81 results
1 of 3 pages