Filtered Results

In your Test Specification document, click the Add Event button. The Configure Event dialog opens. Create the If condition that will trigger the event. Channel value change Click the Select channel button ...

Configure the Logging Specification with the desired settings for your data log file name, location, duration, export, and triggering options. Click the RUN and STOP buttons at the top of any of the documents ...

Select one of the following options depending on your automotive network: Use CAN databases—Manage and configure CAN databases to determine which signals to use in your Channel Specification. Use LIN databases—Manage ...

Low-Speed CAN requires termination at the Low-Speed CAN transceiver instead of on the cable. The termination requires two resistors: RTH for CAN_H and RTL for CAN_L. This configuration allows the NXP fault-tolerant ...

On the Data tab, right-click the log file and select Export. In the Export to CSV file format dialog, specify the desired File location to save your file, if necessary. The default is the same location ...

What to UseThe following FlexLogger and LabVIEW software versions are required to support the SystemLink tag feature: LabVIEW 2017 or later FlexLogger 2018 R4 or later What to Do Install LabVIEW. Install ...

Extend the functionality of FlexLogger by adding a custom plugin to your project. What to UseThe FlexLogger Plugin Development Kit guides you through planning, creating, and testing your custom plugins ...

Select one or more channels you wish to add an alarm to. Hover over a channel row to see the Configure gear . Click the gear for the channel you wish to add an alarm to. Select the Alarms tab in the Channel ...

In your Test Specification document, click the Add Event button. The Configure Event dialog opens. Create the If condition that will trigger the event. Channel value change Click the Select channel button ...

In your Logging specification document, specify values for the Operator and DUT in the Test Properties section, if desired. The fields for Operator and DUT are auto-populated, but can be changed or deleted, ...

Before adding CAN and LIN signals to your Channel Specification, you may need to create or manage the databases that provide the signal definitions and scaling information for your application. Refer to ...

While the test is running, click the Add Note button in the toolbar. A dialog will open, timestamped with the time the button was clicked. Record any information you wish to include in the log file. Note ...

CAN interfaces are software representations of physical ports. Complete the following steps to adjust the port settings. Enable Termination, if necessary. Improperly configured Termination schemes might ...

LIN interfaces are software representations of physical ports. Complete the following steps to adjust the port settings. Enable Termination, if necessary. Improperly configured Termination schemes might ...

Click Add Signals on the CAN port you want to configure. Select the Database that contains the signals you want to update. Select the Cluster that contains the signals you want to apply J1939 to. Select ...

On the Logging Specification document, select Export automatically to CSV file format when logging completes. Specify the CSV file data rate, if necessary. All logged data channels are mapped to a common ...

In your Channel Specification document, select all configured channels you wish to calibrate. In your Channel Specification document toolbar, click the Calibrate channels button . Select one of the following ...

Although it is possible (and supported) in principle to run a network without a database, using a database is highly recommended to have a consistent set of network parameters for all nodes in the network. ...

Configure the Logging Specification with the desired settings for your data log file name, location, duration, export, and triggering options. Click the RUN and STOP buttons at the top of any of the documents ...

Select one or more channels you wish to configure. Hover over a channel row to see the Configure gear . Click the gear for the channel or channels you wish to configure. The configure gear appears when ...

Select one of the following options depending on your automotive network: Use CAN databases—Manage and configure CAN databases to determine which signals to use in your Channel Specification. Use LIN databases—Manage ...

Add a calculated Boolean channel to produce a high or low Boolean digital signal based on an analog or digital channel. On the Channel Specification toolbar, select Add channel Calculation Boolean Formula ...

A calculated channel produces a new value based on calculations performed on other channels in the system. You can choose from the following calculation types: Configuring RMS and Mean Channels Configuring ...

Select one or more channels you wish to configure. Hover over a channel row to see the Configure gear . Click the gear for the channel or channels you wish to configure. The configure gear appears when ...

Complete the following steps to configure the available data rates for your DAQ device: Click the Configure Data Rates button on the toolbar, or click Configure from the Data Rate Level pull-down selector. ...

Refer to the following information to configure your device channels. Configuring I/O Channels Configuring an Automotive Bus Configuring Calculated Channels After you configure your channels, you can start ...

Select one or more channels you wish to configure. Hover over a channel row to see the Configure gear . Click the gear for the channel or channels you wish to configure. The configure gear appears when ...

Add a channel produced by applying either a lowpass or a highpass Butterworth filter to an existing hardware channel. The lowpass or highpass filter channel displays filtered data that excludes any noise ...

Add a calculated channel to analyze or scale data from existing hardware channels. A calculated channel produces a new value based on calculations performed on other channels in the system. On the Channel ...

Add and configure signals to use in your Channel specification. Use any of the following options that apply to the devices in your system: Configure sensors in your Channel Specification Configure digital ...

Showing 1-30 of 77 results
1 of 3 pages