Filtered Results

Hover over the channel row to see the Configure gear . Click the gear for the channel you wish to configure. The channel configuration dialog opens. Use the Name field to specify the channel name, if necessary. ...

LIN interfaces are software representations of physical ports. Complete the following steps to adjust the port settings. Enable Termination, if necessary. Improperly configured Termination schemes might ...

Click Add Signals on the CAN port you want to configure. Select the Database that contains the signals you want to update. Select the Cluster that contains the signals you want to apply J1939 to. Select ...

On the Logging Specification document, select Export automatically to CSV file format when logging completes. Specify the CSV file data rate, if necessary. All logged data channels are mapped to a common ...

Although it is possible (and supported) in principle to run a network without a database, using a database is highly recommended to have a consistent set of network parameters for all nodes in the network. ...

Hover over the channel row to see the Configure gear . Click the gear for the channel you wish to configure. The channel configuration dialog opens. Use the Name field to specify the channel name, if necessary. ...

Add a channel produced by applying either a lowpass or a highpass Butterworth filter to an existing hardware channel. The lowpass or highpass filter channel displays filtered data that excludes any noise ...

Add a calculated channel to analyze or scale data from existing hardware channels. A calculated channel produces a new value based on calculations performed on other channels in the system. In the Channel ...

Add and configure signals to use in your Channel specification. Use any of the following options that apply to the devices in your system: Configure sensors in your Channel Specification Configure digital ...

In your Test Specification document, click the Add Event button. The Event configuration dialog opens. Create the If condition that will trigger the event. Click the Select channel button in the If condition ...

In your Logging specification document, specify values for the Operator and DUT in the Test Properties section, if desired. The fields for Operator and DUT are auto-populated, but can be changed or deleted, ...

Low-Speed CAN requires termination at the Low-Speed CAN transceiver instead of on the cable. The termination requires two resistors: RTH for CAN_H and RTL for CAN_L. This configuration allows the NXP fault-tolerant ...

FlexLogger automatically discovers any installed hardware and displays it in the Channel Specification. Available device channels will be listed beneath the module information. CompactDAQ modules will ...

In your Logging specification document, select a Start condition for your trigger. Selecting any Triggering conditions will enable the trigger. Select from the following trigger start conditions: Project ...

To begin interacting with your measurement system and creating logging and automated test configurations, create a new project in one of the following ways: Create a Data Logging Project from the launcher. ...

If there's a way we could shorten/condense this example, I can see a case for leaving it in this topic. But it's so much longer than the steps themselves the way it is now, which makes the topic less focused. ...

Each LED can display two colors (red or green), which display in the following four patterns: Pattern Meaning Off No LED illumination Solid LED fully illuminated Blink Blinks at a constant rate of several ...

LIN databases allow you to store frames and signals running on the network in a database, as well as information about which ECU is transmitting which data. This information also is needed for each node ...

You must set up the necessary sensors in your measurement system to log data. Configure the logging specification for your log files. Enable and configure triggers for your acquisition. Adding Metadata ...

On the Data tab, right-click the log file and select Export. In the Export to CSV file format dialog, specify the desired File location to save your file, if necessary. The default is the same location ...

You must have channels added and configured for your FlexLogger project in order to visualize data from your sensor signals. Refer to the Configuring Device Channels topic for more information. On the ...

Open or create a FlexLogger Project. Find the hardware devices in your system. Configure Device Channels for data acquisition or signal generation.

Configure your measurement for use in the project by adding signals to the Channel Specification. For information on how to configure signals, refer to the Configuring Device Channels topic. Set up the ...

Complete the following steps to apply scaling to your configured sensor. Click the Configure gear on the channel of the device you wish to scale. The channel configuration dialog opens. In the Scaling ...

Use these methods to set the history length for High Speed Graphs and Long History Graphs. Set the Default History Length Go to FilePreferences and specify your High speed history length or Long history ...

If you are having trouble finding your hardware in the FlexLogger Channel Specification, try the following tips. Refer to the list of supported hardware to confirm that your devices are supported in FlexLogger. ...

Navigate to the Charts palette on your Screen.flxscr document. Click the graph you want to use and drag it onto the Screen. Add the channels you want to visualize to the graph as shown in the Mapping an ...

The following FlexLogger and LabVIEW software versions are required to support the SystemLink tag feature: LabVIEW 2017 or later FlexLogger 2018 R4 or later Install LabVIEW. Install FlexLogger, ensuring ...

On the Data tab, right-click any log file and select Locate in Windows Explorer. Right-click the TDMS log file you want to open and select Open with»Excel Importer.

On the Data tab, double-click the data log file to launch the DIAdem-based FlexLogger TDMS Viewer. If you have a separately licensed version of DIAdem installed, you can configure FlexLogger to launch ...

Showing 1-30 of 60 results
1 of 2 pages