June 2018
This file contains important information about NI-RFmx LTE and is organized into the following sections:
Installed Software, Documentation, and Examples
Product Security and Critical Updates
Increasing Available Memory For Your Application
Automating the Installation of NI Products
Using NI Software with Microsoft Windows 10
Using NI Software with Microsoft Windows 8.1
NI-RFmx LTE 2.5 includes the following new features:
NI-RFmx LTE 2.4 includes the following new features:
NI-RFmx LTE 2.3.1 includes the following new feature:
NI-RFmx LTE 2.3 includes the following new features:
Caution If you are using only RFmx LabVIEW Runtime products, NI recommends uninstalling all the RFmx Runtime products before installing a newer version of RFmx Runtime products.
NI-RFmx drivers require that all the installed driver versions remain the same for proper functionality. This requirement is because NI-RFmx drivers share components. If driver incompatibilities exist, they are reported through a dialog box after installation. You can also use the Version Compatibility Checker utility to manually check for version incompatibilities. Refer to the Installed Software, Documentation, and Examples section for more information about the installed location of the Version Compatibility Checker utility.
Device-specific information about these modules is included in the NI RF Vector Signal Analyzers Help.
Device-specific information about these modules is included in the NI RF Vector Signal Transceivers Help.
NI-RFmx LTE 2.5 supports the following operating systems:
Note In 2016, NI-RFmx LTE dropped support for Microsoft Windows 7 RTM (with no service pack), Windows Vista, Windows XP, and Windows Server 2003. NI-RFmx LTE 2.5 will not install or run on an unsupported OS. You cannot deploy or distribute applications that use NI-RFmx LTE 2.5 to an unsupported OS. Additionally, after installing NI-RFmx LTE 2.5, you cannot use any installers built on this computer with any version of LabVIEW, LabWindows™/CVI™, NI TestStand™, or Measurement Studio on an unsupported OS.
For more information about the changes to our OS support for 2017, refer to KB 79UC78LS, Why Does my LabVIEW, LabWindows/CVI, Measurement Studio, or TestStand Built Installer Fail on Windows XP/Vista and Server 2003?.
1 NI software installs VC2015 Runtime and .NET 4.6.2. Windows 8.1 and Windows Server 2012 R2 require Microsoft updates to support these items. Refer to Microsoft KB2919442 and KB2919355 for more information about how to install these updates.
2 NI software is signed with a SHA-256 certificate. Windows 7 SP1, Windows Embedded Standard 7 SP1, and Windows Server 2008 R2 SP1 require Microsoft updates to support SHA-256. Refer to Microsoft KB3033929 for more information about how to install this security update.
Note NI-RFmx LTE 2.5 does not support Windows Server non-R2 editions.
NI recommends that you have the most recent service pack for your operating system installed.
*Depending on the amount of data acquired and/or processed, a larger amount of memory may be required.
Note For better responsiveness of the NI-RFmx Soft Front Panel on a remote desktop, National Instruments recommends changing the remote desktop connection colors setting to be 16-bit color depth.
Note You should install ADEs, such as NI LabVIEW or Microsoft Visual Studio®, before installing NI-RFmx LTE. To add support for ADEs installed after installing NI-RFmx LTE, modify your NI-RFmx LTE installation or launch the NI-RFmx LTE installer again.
Note NI-RFmx LTE does not operate correctly without the service packs and patches previously mentioned.
Item | Installed Location |
---|---|
Version Compatibility Checker | <NIDir>\RFmx\niRFmxCompatibility_Checker.exe |
Debug Configuration Utility | <NIDir>\RFmx\niRFmxDebugConfigurationUtility.exe |
DLLs | <SYSDIR> |
Header files | <NIDir>\Shared\ExternalCompilerSupport\C\include |
Import Library files (32-bit) | <NIDir>\Shared\ExternalCompilerSupport\C\include |
Import Library files (64-bit) |
|
C, .NET | |
Examples | <NIDocDir>\NI-RFmx\LTE\Examples |
LabVIEW | |
Examples | <NIDir>\LabVIEW <version>\examples\RFmx\LTE |
.NET Class Libraries | |
Assemblies | <MSTUDIOVS2010DIR>\DotNET\Assemblies\Current\NationalInstruments.RFmx.LteMX.Fx40.dll <MSTUDIOVS2010DIR>\DotNET\Assemblies\Current\NationalInstruments.RFmx.InstrMX.Fx40.dll <MSTUDIOVS2010DIR>\DotNET\Assemblies\Current\NationalInstruments.Common.dll |
In 32-bit OS, select Start»All Programs»National Instruments»NI-RFmx LTE»NI-RFmx LTE Measurement Interactive Panel to launch the NI-RFmx LTE Measurement Interactive Panel (32-bit).
Select Start»All Programs»National Instruments»NI-RFmx LTE»NI-RFmx Soft Front Panel to launch the NI-RFmx Soft Front Panel (64-bit).
Note NI-RFmx Soft Front Panel does not support the following LTE measurements:
However, these measurements are supported in NI-RFmx LTE Measurement Interactive Panel.
Documentation for NI-RFmx LTE is located at Start»All Programs»National Instruments»NI-RFmx LTE»NI-RFmx LTE Documentation. The documentation set is composed of the following documents.
Document | Format | Description |
---|---|---|
NI-RFmx LTE Help | HTML/Windows Help | Information about NI-RFmx LTE. This help file is an HTML version of a traditional user manual that includes the following information:
|
NI-RFmx LTE 2.5 Readme | HTML (this document) | Information about supported hardware, operating systems, and legal notices. |
For the most recent revisions of documentation and for newly released documentation, visit ni.com/manuals.
NI-RFmx LTE palette VIs are available from the Functions»Measurement I/O»NI-RFmx»LTE palette.
You can access all the installed NI-RFmx LTE examples at Start»All Programs»National Instruments»NI-RFmx LTE»NI-RFmx LTE Examples.
Visit ni.com/security to view and subscribe to receive security notifications about National Instruments products. Visit ni.com/critical-updates for information about critical updates from National Instruments.
The following items are the behavior changes in NI-RFmx LTE 2.5 from NI-RFmx LTE 2.4.
The following items are the behavior changes in NI-RFmx LTE 2.3.1 from NI-RFmx LTE 2.3.
You can access the software and documentation known issues list online. Refer to the NI-RFmx LTE 2.5 Known Issues at ni.com for an up-to-date list of known issues in NI-RFmx LTE 2.5.
The following items are the IDs and titles of a subset of issues fixed in NI-RFmx LTE. This is not an exhaustive list of issues fixed in the current version of the NI-RFmx LTE. If you have a CAR ID, you can search this list to validate that the issue has been fixed.
The following items are changes in NI-RFmx LTE 2.4 from NI-RFmx LTE 2.3.1.
ID | Fixed Issue |
---|---|
665930 | Fixed an issue where in-band emission (IBE) test requirement table for release 8-10 UEs is made 3GPP Specification release 14 compliant. |
664616 | Fixed an issue where LTE uplink equalizer coefficients are calculated using the least square method as per section E.3.3 of 3GPP TS 36.521-1 specification. |
655346 | Fixed an issue where DMRS auto-detect was internally getting enabled when hopping is enabled. |
654382 | Fixed an issue with using special subframes in case of DL TDD for channel estimation. |
630327 | Fixed an issue with computing channel estimation and CFO for the slots under measurement to improve standard deviation of EVM. |
640495 | Fixed an issue where switching between measurements from an NI-RFmx cellular personality to Demod, resulted in higher EVM on 5668R. |
The following items are changes in NI-RFmx LTE 2.3.1 from NI-RFmx LTE 2.3.
ID | Fixed Issue |
---|---|
650095 | Fixed an issue where the RFmxInstr Close API did not abort a measurement in progress, but instead waited for the measurement to finish before closing. |
650083 | Fixed an issue with RFmxInstr Save All Configurations API to save the attribute configurations depending on the corresponding number of channels configured by user. |
648703 | Fixed an issue where passing NULL as selector string in a few C functions, caused the function to crash. |
655756 | Fixed an issue where values were swapped on configuring the SEM Offset Start Freq property higher than the SEM Offset Start Freq property. |
646771 | Fixed an issue with configuring SEM offsets, other than offset0, when the Mask Type is Custom. |
The following items are changes in NI-RFmx LTE 2.3 from NI-RFmx LTE 2.2.
ID | Fixed Issue |
---|---|
631432 | Fixed an issue where incorrect values were returned on reading RF Attenuation and Mechanical Attenuation properties. |
622407 | Fixed an issue with configuring SEM custom offsets with a named signal. |
625184 | Fixed an issue with retrieving the value of the SEM Offset RBW property when the mask type is Custom. |
623095 | Fixed an issue with the Analysis-Only mode, ModAcc measurement does not require configuration of pre-trigger delay in t0 value of the I/Q waveforms. |
When developing memory intensive applications, you may encounter memory limits as 32-bit Windows applications only utilize 2 GB of memory by default. To expand the amount of memory an application can utilize, you can configure the executable to be large address aware to gain access to up to 3 GB of memory on a 32-bit Windows operating system and up to 4 GB of memory on a 64-bit Windows operating system.
For more information, refer to Memory Limits for Windows and Windows Server Releases on the Microsoft website.
Note LabVIEW 8.5 and later are large address aware. For more information, refer to How Much Memory can LabVIEW 32-bit or 64-bit Use?. |
In TestStand 2013 and later, the Large Address Aware flag is enabled by default for the TestStand Sequence Editor and TestStand User Interfaces. For more information, refer to Using the Large Address Aware Flag With TestStand Applications.
You can automate the installation of most NI products using command-line arguments to suppress some or all of the installer user interface and dialog boxes. However, starting with the August 2012 releases (products using NI Installers version 3.1 or later), you may need to perform additional steps before or during a silent installation of NI software.
If the NI product you are installing uses Microsoft .NET 4.0, the .NET installer may run before any NI software installs and may require a reboot before the installation of NI software begins. To avoid a .NET reboot, install .NET 4.0 separately before you install NI software.
For more information about automating the installation of NI products, refer to the following KnowledgeBase articles:
Microsoft Windows 10 is the latest version of the Windows operating system and features significant changes compared to previous versions. Windows 10 introduces several new capabilities and also combines features from both Windows 7 and Windows 8.1. For more information about NI support for Windows 10, visit ni.com/windows10.
When you install National Instruments software on Microsoft Windows 8.1, you will notice a few additional tiles in the Apps view, including shortcuts to NI application software products such as NI LabVIEW, Measurement & Automation Explorer (NI MAX), and NI Launcher. For more information about NI support for Windows 8.1, visit ni.com/windows8.
Copyright
© 2015–2018 National Instruments. All rights reserved.
Under the copyright laws, this publication may not be reproduced or transmitted in any form, electronic or mechanical, including photocopying, recording, storing in an information retrieval system, or translating, in whole or in part, without the prior written consent of National Instruments Corporation.
National Instruments respects the intellectual property of others, and we ask our users to do the same. NI software is protected by copyright and other intellectual property laws. Where NI software may be used to reproduce software or other materials belonging to others, you may use NI software only to reproduce materials that you may reproduce in accordance with the terms of any applicable license or other legal restriction.
End-User License Agreements and Third-Party Legal Notices
You can find end-user license agreements (EULAs) and third-party legal notices in the following locations after installation:
U.S. Government Restricted Rights
If you are an agency, department, or other entity of the United States Government ("Government"), the use, duplication, reproduction, release, modification, disclosure or transfer of the technical data included in this manual is governed by the Restricted Rights provisions under Federal Acquisition Regulation 52.227-14 for civilian agencies and Defense Federal Acquisition Regulation Supplement Section 252.227-7014 and 252.227-7015 for military agencies.
IVI Foundation Copyright Notice
Content from the IVI specifications reproduced with permission from the IVI Foundation.
The IVI Foundation and its member companies make no warranty of any kind with regard to this material, including, but not limited to, the implied warranties of merchantability and fitness for a particular purpose. The IVI Foundation and its member companies shall not be liable for errors contained herein or for incidental or consequential damages in connection with the furnishing, performance, or use of this material.
Trademarks
Refer to the NI Trademarks and Logo Guidelines at ni.com/trademarks for information on National Instruments trademarks. Other product and company names mentioned herein are trademarks or trade names of their respective companies.
Patents
For patents covering the National Instruments products/technology, refer to the appropriate location: Help»Patents in your software, the patents.txt file on your media, or the National Instruments Patent Notice at ni.com/patents.
375558G-01