From 04:00 PM CDT – 08:00 PM CDT (09:00 PM UTC – 01:00 AM UTC) Tuesday, April 16, ni.com will undergo system upgrades that may result in temporary service interruption.
We appreciate your patience as we improve our online experience.
From 04:00 PM CDT – 08:00 PM CDT (09:00 PM UTC – 01:00 AM UTC) Tuesday, April 16, ni.com will undergo system upgrades that may result in temporary service interruption.
We appreciate your patience as we improve our online experience.
June 2017
This file contains important information about NI-RFSG, including new features, supported hardware, a partial list of bugs fixed for NI-RFSG 17.1, and known issues.
Installed Software, Documentation, and Examples
Product Security and Critical Updates
IVI Compliance Package Functionality
Automating the Installation of NI Products
Using NI Software with Microsoft Windows 10
Using NI Software with Microsoft Windows 8.1
This software installation provides support for customers using RF signal generator hardware, as specified in the Supported Hardware section. To program your RF signal generator, use the NI-RFSG instrument driver or NI-RFSG Soft Front Panel (SFP).
The getting started guide for your device provides information about how to install, configure, test, and begin using a RF signal generator.
NI-RFSG 17.1 includes the following new features:
NI-RFSG 17.0 adds support for LabVIEW 2017 (32- and 64-bit)
NI-RFSG 16.0 includes the following new features:
NI-RFSG 15.0.3 includes the following new features:
NI-RFSG 15.0.2 includes the following new features:
NI-RFSG 15.0 includes the following new features:
The following table shows which hardware products are supported in the NI-RFSG instrument driver and the NI-RFSG SFP. The following hardware products are supported in all operating systems listed in the Supported Operating Systems section.
| Hardware Product | NI-RFSG | NI-RFSG SFP |
|---|---|---|
| PXI-5610 | √ | — |
| PXIe-5611 | √ | — |
| PXIe-5644 | √ | √ |
| PXIe-5645 | √ | √ |
| PXIe-5646 | √ | √ |
| PXI/PXIe-5650 | √ | √ |
| PXI/PXIe-5651 | √ | √ |
| PXI/PXIe-5652 | √ | √ |
| PXIe-5653 | √ | — |
| PXIe-5654 | √ | √ |
| PXIe-5654 with PXIe-5696 | √ | √ |
| PXI-5670 | √ | √ |
| PXI-5671 | √ | √ |
| PXIe-5672 | √ | √ |
| PXIe-5673/5673E | √ | √ |
| PXIe-5820 | √ | |
| PXIe-5840 | √ | √ |
Note Some hardware products are not supported by the NI-DAQmx-based runtime. Visit ni.com/info and enter the Info Code rfsgdevices for more information about which NI-RFSG devices are supported by the NI-DAQmx-based runtime.
Note MXI Express and MXI-4 are supported on Windows 10/8.1/7.
NI-RFSG has the following minimum requirements:
*Depending on the amount of data acquired and/or processed, a larger amount of memory may be required.
Note Guest accounts are not supported under any OS.
NI-RFSG 17.1 and NI-RFSG Soft Front Panel 17.0 support the following operating systems:
Note In 2016 NI-RFSG dropped support for Windows Vista, Windows XP, Windows Server 2003, and installations of Windows 7 without any service packs. NI-RFSG 17.1 will not install or run on an unsupported OS. You cannot deploy or distribute applications that use NI-RFSG 17.1 to an unsupported OS. Additionally, after installing NI-RFSG 17.1, you cannot use any installers built on this computer with any version of LabVIEW, LabWindows™/CVI™, NI TestStand™, or Measurement Studio on an unsupported OS.
For more information about the changes to our OS support for 2016, refer to KB 79UC78LS, Why Does My LabVIEW, LabWindows/CVI, Measurement Studio, or TestStand Built Installer Fail on Windows XP/Vista and Server 2003?.
1 NI software installs VC2015 Runtime and .NET 4.6.2. Windows 8.1 and Windows Server 2012 R2 require Microsoft updates to support these items. Refer to Microsoft KB2919442 and KB2919355 for more information about how to install these updates.
2 NI software is signed with a SHA-256 certificate. Windows 7 SP1 and Windows Server 2008 R2 SP1 require Microsoft updates to support SHA-256. Refer to Microsoft KB3033929 for more information about how to install this security update.
Note NI-RFSG 17.1 does not support Windows Server non-R2 editions.
NI recommends that you have the most recent service pack for your operating system installed.
NI-RFSG supports the following application software versions, including service packs. You should install application software, such as LabVIEW, LabWindows/CVI or Microsoft Visual Studio®, before installing NI-RFSG. To add support for ADEs installed after installing NI-RFSG, modify your NI-RFSG installation or launch the NI-RFSG installer again. If you are not using NI application software, refer to Microsoft Visual Studio Support.
| Application Software | Versions Supported by NI-RFSG |
|---|---|
| LabVIEW | 2014 SP1, 2015 SP1, 2016, or 2017 |
| LabVIEW Real-Time Module | 2014 SP1, 2015 SP1, 2016, or 2017 |
| LabWindows/CVI | 2010 and later |
| LabWindows/CVI Real-Time Module | 2010 and later |
Note When using NI-RFSG with LabVIEW Real-Time Module or LabWindows/CVI Real-Time Module, the PXIe-5644/5645/5646, PXIe-5654/5654 with PXIe-5696, and PXIe-5820/5840 devices are not supported.
Note Install any toolkits or add-on software you intend to use with the NI-RFSG instrument driver after NI-RFSG installation is complete. Refer to the getting started guide for your device for more information about software and hardware installation.
Note MXI users must install the software included with the MXI hardware.
| Note | $(IVIROOTDIR32) is configured as an environment variable on the target system. |
If you upgraded an installation of IVI, your files may be located in the following location:
|
| Note | $(IVIROOTDIR64) is configured as an environment variable on the target system. |
| Item | Installed Location |
|---|---|
| NI-RFSG | <IVIROOTDIR32>\Drivers\niRFSG |
| NI-RFSG Function Panel | <IVIROOTDIR32>\Drivers\niRFSG\niRFSG.fp |
| NI-RFSG Examples | <NIDocDir>\NI-RFSG\Examples |
| NI-RFSG Header files | <IVIROOTDIR32>\Include |
| NI-RFSG Import Library files (32-bit) | <IVIROOTDIR32>\Lib |
| NI-RFSG DLL (32-bit) | <IVIROOTDIR32>\Bin |
| NI-RFSG SFP | <IVIROOTDIR32>\Drivers\niRFSG |
| NI-RFSG SFP Example Waveforms | <NIDocDir>\NI-RFSG Soft Front Panel\examples\Waveforms |
| Item | Installed Location |
|---|---|
| NI-RFSG Function Panel | <IVIROOTDIR64>\Drivers\niRFSG\niRFSG.fp |
| NI-RFSG Header files | <IVIROOTDIR64>\Include |
| NI-RFSG Import Library files (64-bit) | <IVIROOTDIR64>\Lib_x64 |
| NI-RFSG DLL (64-bit) | <IVIROOTDIR64>\Bin |
Note To use the .NET API, you must install the the .NET class libraries or the .NET Wrapper in addition to the NI device driver. For information about versions of the .NET Framework and the drivers each supports, as well as the download location of the installer files, refer to the National Instruments .NET Driver Support document at ni.com/info and enter Info Code NETAPIdriversupport.
To launch the NI-RFSG SFP, navigate to Start»All Programs»National Instruments»NI-RFSG»NI-RFSG Soft Front Panel.
Documentation for NI-RFSG is located at Start»All Programs»National Instruments»NI-RFSG»Documentation. The documentation set is composed of the following documents.
| Document | Format | Description |
|---|---|---|
| NI RF Signal Generators Help | HTML/Windows Help | Contains primary help content for NI-RFSG products. The help is an HTML version of a traditional user manual that includes the following information:
|
| Getting Started Guide for your device | Printed and PDF | Contains software and hardware installation, MAX configuration, signal connection, and troubleshooting information for your device. |
| Specifications for your device | Lists technical specifications for your device. | |
| Calibration Procedure for your device | Contains calibration instructions for your device. | |
| NI-RFSG Readme | HTML (this document) | Contains information about supported hardware and operating systems, new features, fixed issues, and legal notices. |
| Introduction to niRFSG | HTML | Contains information about driver documentation, examples, connecting to your instrument, configuring instrument settings, and known issues. |
| NI-RFSG IVI Compliance Document | TXT | Contains information about IVI compliance. |
For the most recent revisions of documentation and for newly released documentation, visit ni.com/manuals.
Note To view PDFs, you need to have Adobe Acrobat Reader installed. You can install the viewer from www.adobe.com/acrobat.
NI-RFSG VIs are available in LabVIEW from the Functions»Measurement I/O»NI-RFSG palette.
NI-RFSG functions are available in LabWindows/CVI from the Instrument menu. To load the NI-RFSG function panel (.fp), select Instrument»Load, and navigate to <IVIROOTDIR32>\Drivers\niRFSG\niRFSG.fp or <IVIROOTDIR64>\Drivers\niRFSG\niRFSG.fp.
In LabVIEW and LabWindows/CVI, you can use the NI Example Finder to search or browse examples. Select Help»Find Examples from LabVIEW or LabWindows/CVI to launch the NI Example Finder. NI-RFSG examples are classified by keyword, so you can search for a particular device or measurement function. The NI Example Finder offers two ways to access all installed LabVIEW example VIs (including NI-RFSG and Modulation Toolkit examples) and their descriptions:
You can also access all the installed NI-RFSG examples for LabVIEW and LabWindows/CVI at Start»All Programs»National Instruments»NI-RFSG»Examples.
Examples are also available online that demonstrate integrating NI RF signal generators with NI RF signal analyzers and NI toolkit software including the Modulation Toolkit. Refer to ni.com/examples for these examples and for more information.
Visit ni.com/security to view and subscribe to receive security notifications about National Instruments products. Visit ni.com/critical-updates for information about critical updates from National Instruments.
As part of the NI-RFSG 17.1 installation, the following software is installed. To completely remove the NI-RFSG 17.1 installation from your system, you must also remove all of the following packages:
| Caution: | Several of the software packages listed above are shared with other NI software packages. If you attempt to remove a piece of software that something else is dependent upon, a message warns you about the software dependencies. You can choose to either uninstall all of the software or to leave the shared software installed. If you choose to uninstall the shared software, some of your other NI software may no longer function correctly. |
Note Do not attempt to uninstall by manually deleting files.
NI-RFSG no longer installs IVI Compliance Pacakge. NI-RFSG supports IVI configuration and runtime, but no longer supports the following features:
If you want to use the above features, you must install IVI Compliance Package separately, either from ni.com/downloads or from the NI Device Drivers 2017 DVD.
You can access the software and documentation known issues list online. Refer to the following locations at ni.com for an up-to-date list of known issues in NI-RFSG 17.1 and NI-RFSG SFP 17.0.
The following items are the IDs and titles of a subset of issues fixed between NI-RFSG instrument driver revisions. This table is not an exhaustive list of issues fixed in the current version of NI-RFSG.
NI-RFSG 17.1
| ID | Fixed Issue |
|---|---|
| 601860 | Fixed an issue where an error occured when changing the device name of the PXIe-5840 in MAX. |
| 515837 | Fixed an issue where the PXIe-5654 device name persisted for other devices inserted into the same slot. |
| 640124 | Fixed an issue where the PXIe-5840 could show a slow phase drift below 400 MHz. |
| 541356 | Fixed an issue where attribute names did not show up correctly in I/O trace. |
| 479015 | Fixed an issue where the niRFSG Reset VI and the niRFSG_reset function did not re-enable the output for the PXIe-5645. |
| 573420 | Fixed an issue where the default value of the Impairment Enabled property and the NIRFSG_ATTR_IQ_IMPAIRMENT_ENABLED attribute for the PXIe-5644/5645/5646 was incorrect. |
| 637641 | Fixed an issue where the PXI-5671 would incorrectly error with markers on a quantum of two when the DUC (digital upconverter) was enabled. |
NI-RFSG 16.0
| ID | Fixed Issue |
|---|---|
| 560185 | Fixed an issue where the power level is incorrect until the amplification path is specified on the PXIe-5654 with PXIe-5696. |
| 570905 | Fixed an issue where after first commit, changes to the Waveform Repeat Count property or NIRFSG_ATTR_WAVEFORM_REPEAT_COUNT attribute and Waveform Repeat Count Is Finite property or NIRFSG_ATTR_WAVEFORM_REPEAT_COUNT_IS_FINITE attribute are ignored. |
NI-RFSG 15.0.3
| ID | Fixed Issue |
|---|---|
| N/A | Fixed an issue where some PXI/PXIe-5650/5651/5652 devices fail calibration verification after calibration adjustment. |
| 562364 | Fixed an issue where incorrect power output occurred on the PXI-5670/5671 and PXIe-5672 for signals less than 2.5 MHz during Arb Waveform generation mode with digital equalization enabled. |
NI-RFSG 14.5
| ID | Fixed Issue |
|---|---|
| 489122 | Fixed an issue where the PXI/PXIe-5652 appears outside of the composite device in MAX. |
NI-RFSG 14.0.1
| ID | Fixed Issue |
|---|---|
| 492490 | Fixed an issue where LabVIEW Run-Time Engine 2013 SP1 does not install with NI-RFSG. |
NI-RFSG 14.0
| ID | Fixed Issue |
|---|---|
| 466905 | Fixed an issue where set frequency and power level execution time takes longer than expected on the PXIe-5644/5645/5646. |
The following items are the IDs and titles of a subset of issues fixed between NI-RFSG SFP revisions. This table is not an exhaustive list of issues fixed in the current version of the NI-RFSG SFP.
NI-RFSG SFP 16.0
| Bug ID | Fixed Issue |
|---|---|
| 575506 | Fixed an issue where changing external gain was not available for the PXIe-5644/5645/5646. |
NI-RFSG SFP 15.0.3
| Bug ID | Fixed Issue |
|---|---|
| 549309 | Fixed an issue where incorrect power output occurred after self-calibration on the PXIe-5672. |
You can automate the installation of most NI products using command-line arguments to suppress some or all of the installer user interface and dialog boxes. However, starting with the August 2012 releases (products using NI Installers version 3.1 or later), you may need to perform additional steps before or during a silent installation of NI software.
If the NI product you are installing uses Microsoft .NET 4.0, the .NET installer may run before any NI software installs and may require a reboot before the installation of NI software begins. To avoid a .NET reboot, install .NET 4.0 separately before you install NI software.
For more information about automating the installation of NI products, refer to the following KnowledgeBase articles:
Microsoft Windows 10 is the latest version of the Windows operating system and features significant changes compared to previous versions. Windows 10 introduces several new capabilities and also combines features from both Windows 7 and Windows 8. For more information about NI support for Windows 10, visit ni.com/windows10.
When you install NI software on Microsoft Windows 8.1, you will notice a few additional tiles in the Apps view, including shortcuts to NI application software products such as NI LabVIEW, Measurement & Automation Explorer (NI MAX), and NI Launcher. For more information about NI support for Windows 8.1, visit ni.com/windows8.
Copyright
© 2004–2017 National Instruments. All rights reserved.
Under the copyright laws, this publication may not be reproduced or transmitted in any form, electronic or mechanical, including photocopying, recording, storing in an information retrieval system, or translating, in whole or in part, without the prior written consent of National Instruments Corporation.
NI respects the intellectual property of others, and we ask our users to do the same. NI software is protected by copyright and other intellectual property laws. Where NI software may be used to reproduce software or other materials belonging to others, you may use NI software only to reproduce materials that you may reproduce in accordance with the terms of any applicable license or other legal restriction.
End-User License Agreements and Third-Party Legal Notices
You can find end-user license agreements (EULAs) and third-party legal notices in the following locations after installation:
U.S. Government Restricted Rights
If you are an agency, department, or other entity of the United States Government ("Government"), the use, duplication, reproduction, release, modification, disclosure or transfer of the technical data included in this manual is governed by the Restricted Rights provisions under Federal Acquisition Regulation 52.227-14 for civilian agencies and Defense Federal Acquisition Regulation Supplement Section 252.227-7014 and 252.227-7015 for military agencies.
IVI Foundation Copyright Notice
Content from the IVI specifications reproduced with permission from the IVI Foundation.
The IVI Foundation and its member companies make no warranty of any kind with regard to this material, including, but not limited to, the implied warranties of merchantability and fitness for a particular purpose. The IVI Foundation and its member companies shall not be liable for errors contained herein or for incidental or consequential damages in connection with the furnishing, performance, or use of this material.
Trademarks
Refer to the NI Trademarks and Logo Guidelines at ni.com/trademarks for information on NI trademarks. Other product and company names mentioned herein are trademarks or trade names of their respective companies.
Patents
For patents covering the NI products/technology, refer to the appropriate location: Help»Patents in your software, the patents.txt file on your media, or the NI Patent Notice at ni.com/patents.
374769J-01