National Instruments cannot guarantee that the configuration of 3rd-party computer systems will not change over time. Therefore, NI provides a list of LabVIEW Real-Time compatible components rather than recommending specific 3rd-party systems. These requirements must be met by the computer system in order to run LabVIEW or LabWindows/CVI Real-Time.
The table below lists the supported processors for the different Real-Time versions. In the chart below, LabVIEW Real-Time version 7.1 supports only Intel® Pentium® 3 and Intel® Pentium® 4 processors. All later version of LabVIEW Real-Time also support the Intel® Pentium® 3 and Intel® Pentium® 4.
|LabVIEW Real-Time version
Intel® Pentium® 3
Intel® Pentium® 4
Intel® Pentium® M
AMD Athlon™ 64
AMD Athlon™ XP
Intel® Core 2 family of processors
Intel® Pentium® D
Intel® Multi-core Xeon®
AMD Multi-core Opteron®
Intel® Core i3
Intel® Core i5
Intel® Core i7
Intel® Core i3 (Sandy Bridge architecture)
Intel® Core i5 (Sandy Bridge architecture)
Intel® Core i7 (Sandy Bridge architecture)
AMD Quad-Core A6-Series APUs
Intel® Core i3 (Ivy Bridge architecture)
Intel® Core i5 (Ivy Bridge architecture)
Intel® Core i7 (Ivy Bridge architecture)
Intel® Core i3 (Haswell architecture)
Intel® Core i5 (Haswell architecture)
Intel® Core i7 (Haswell architecture)
NOTE The 2014+ hardware architectures have been tested and confirmed to work with LabVIEW 2018.. NI does not plan on testing new RT PC compatible hardware for future version of LabVIEW.
Supported Ethernet Chipsets:
A network adapter with a supported ethernet chipset is required. The adapter can be integrated with the motherboard or PCI. Network interface card (NIC) chipset manufacturers may produce various configurations of a given NIC with an identical model number. Some NICs will have a model number different from the installed chipset. To check if your NIC is a supported chipset, review the specifications section for the NIC to determine the embedded chipset. If you are using a separate NIC and want to disable the built-in one, do so in the BIOS.
In the table below, the model number may be followed by the product ID (also known as chipset ID or model ID) in quotes. Note that if an ID is listed for a given model, only chipsets with that ID will be supported. For more information on the model ID of a particular chipset, look in the product specifications or contact the manufacturer.
|LabVIEW Real-Time Version
||Supported Ethernet Chipsets
Intel® 82559 "0x1229"
Intel® 82559er "0x1209"
NI-PCI-8232 GPIB/Gigabit Ethernet
Broadcom® BCM5751 "0x1677"
Intel® InBusiness® 82559 "0x103A"82562em "0x2449"
Intel® 82562et "0x1039"
Intel® 82562etb "0x103B"
Intel® Pro/100 VM "0x1033, 0x1034, 0x1038, 0x103C, 0x103E"
Intel® Pro/100 VE "0x1032, 0x103D"
Intel® 82801 CAM (ICH3) "0x1031, 0x1035, 0x1036, 0x1037"
Intel® 82540EM "0x100E"
Intel® 82541EI "0x1013"
Intel® 82541EP "0x1018"
Intel® 82541GI "0x1076"
Intel® 82541GI-Mobile "0x1077"
Intel® 82541ER "0x1078"
Intel® 82573E/V "0x108B"
Intel® 82573E/V w/AMT "0x108C"
Intel® 82573L "0x109A"
nVidia® nForce MCP
nVidia® nForce MCP2
nVidia® nForce MCP3
nVidia® nForce 400 MCP4
nVidia® nForce 400 MCP5
nVidia® nForce 250 MCP6
nVidia® nForce MCP7
nVidia® nForce CK804 MCP8
nVidia® nForce CK804 MCP9
nVidia® nForce 430 MCP12
nVidia® nForce 430 MCP13
nVidia® nForce MCP04
nVidia® nForce MCP55
nVidia® nForce MCP61
nVidia® nForce MCP65
Intel® 82572 - Quadport
Intel® 82567 "0x10BE" and "0x10F5"
VLX Emulated Ethernet
Intel® 82574L CT "0x10D3"
Intel® 82546EB PCI-X Ethernet "0x1010"
Intel® 82546EB PCI-X Ethernet "0x1079"
Intel® 82545EM PCI-X Ethernet "0x100F"
Intel® 82545GM PCI-X Ethernet "0x1026"
Intel® 82540EP_LP Ethernet "0x101E"
Intel® 82545EM Ethernet "0x100F"
Intel® 82545GM Ethernet "0x1026"
Intel® 82572EI Ethernet "0x10B9"
Intel® 4-port LP(2x82571EB) Ethernet "0x10BC"
Intel® PCH-LM 82577 (Hanksville) "0x10EA"
Intel® PCH-LC 82577 (Hanksville) "0x10EB"
Intel® PCH-DM 82577 (Hanksville) "0x10EF"
Intel® PCH-DC 82577 (Hanksville) "0x10F0"
Intel® 82541PI "0x107C"
Intel® 82579LM (Lewisville)
Intel® 82579V (Lewisville)
Intel® I217-LM Gigabit Clarkville Ethernet
Intel® I217-V Gigabit Clarkville Ethernet
Intel® I210-AS Gigabit Ethernet
Intel® I210-AT Gigabit Ethernet
Intel® I210-CS Gigabit Ethernet
Intel® I210-IS Gigabit Ethernet
Intel® I210-IT Gigabit Ethernet
*This Ethernet chipset is not natively supported by the LabVIEW 2011 Real-Time module. Support can be added by using the USB utilities and Ethernet drivers linked in the Downloads section. The attached drivers also include important patches; these drivers are recommended for all new Real-Time PCs. The readme file included in the ZIP file provides instructions for running the utilities.
An example of a board that carries the Intel® 82540 chipset is the NI-PCI-8232 GPIB/Gigabit Ethernet. An example of a commercially available board that carries the 82550 chipset is the Intel Pro/100 S.
All LabVIEW Real-Time versions support Parallel ATA in IDE while LabVIEW 8.5 (and above) and LabWindows/CVI RT 8.5 (and above) support Serial ATA only in AHCI. LabVIEW Real-Time and LabWindows/CVI RT versions prior to 8.5 do not support Serial ATA. LabVIEW Real-Time 8.6.1 and previous supports hard drives up to 126 GiB. LabVIEW Real-Time 2009 and above support hard drives up to 1.99 TiB. The following options may be available depending on the specific desktop PC.
- A Parallel ATA drive can be installed and the Serial ATA controllers can be disabled in the BIOS.
- The BIOS may have the option of setting the Serial ATA controller to a mode making the drive appear to be Parallel ATA. This may be referred to with different names such as "PATA", "Legacy", "Compatibility", or other names. An example of this mode is discussed in section 4.1 of Intel® 82801EB (ICH5) and Intel® 82801ER (ICH5R) Serial ATA Controller - Programmer’s Reference Manual (PRM). Some PC BIOS may not support this mode, such as the Dell Precision 360. Sometimes it is helpful to disable the UDMA-mode.
- If AHCI, IDE or compatibility/legacy mode isn't available or doesn't work, try RAID to get HDD recognized
LabVIEW Real-Time currently supports up to 4 GB (gigabytes) of RAM. In Real-Time 8.5 and previous, more than 2 GB of RAM will cause deployment errors. In LabVIEW Real-Time 8.5.1 through 2009 SP1, support is provided for systems with RAM greater than 2 GB, however the real-time operating system will only utilize 2 GB. LabVIEW Real-Time 2010 and later utilizes up to 4 GB.
The volt rails should be 3.3 and 5 volts on the motherboard. Some server class, industrial, or non-dell motherboards may lack the 3.3 volt rail required by National Instruments M-Series boards. The BIOS may have a description of the power rails supported by the motherboard.