Archived: Emona ETT-202 DATEx Specifications

NI does not actively maintain this document.

This content provides support for older products and technology, so you may notice outdated links or obsolete information about operating systems or other relevant products.


Technical specifications for the EMONA ETT-202 DATEx add-in board for the NI ELVIS platform.


NI ELVIS Functions

NI ELVIS Platform functions available at the ETT-202 front panel:

All NI ELVIS functions provided are directly connected to the NI ELVIS signals, and their performance is in accordance with NI ELVIS specifications.

Digital I/O:

Digital inputs D IN-0 to IN-3

Digital outputs D OUT-0 to OUT-3

Function Generator:

Input VCO IN;


Analog I/O:

Inputs ACH0 and ACH1

Outputs DAC0 and DAC1

Variable Power Supplies:

Outputs "+" and "-"

ETT-202 Functional Modeling Blocks

Adder 1:

Dual input

Variable gain from 0 to 2 (inverting)

Bandwidth approx. 600kHz

Adder 2:

Dual input

Fixed gain of 1

Bandwidth approx. 600kHz


Bandwidth: DC to approx. 600kHz

Gain: 0.2 to 10

Channel Module:


Fcenter = 100kHz;

Passband = 24kHz; (from 88 kHz & 112 kHz)

Stopband = 140kHz, -35dB (approximately at 30kHz & 170kHz);

Gain = 1;

Type: 6th order Chebychev with 0.1dB ripple


Fcut-off = 1.6 kHz;

Gain = 0.9;

Type: 4th order Butterworth

Dual Analog Switch & Sample/Hold

Analog Input Bandwidth 50kHz

Maximum CONTROL clock 100kHz

CONTROL Input Levels digital-level only, 0V and 5V

Maximum Analog Input Level 4Vpk-pk

Headphone Amplifier

Output power 125mW, stereo socket

Headphone Type and Connector 3.5mm stereo, > 8ohm impedance

Line Code Encoder

Input data from SEQUENCE GENERATOR “X” data sequence

CLK same digital-level clock as SEQUENCE GENERATOR CLK signal,

fmax > 100kHz

Line codes: NRZ-L, RZ-AMI, Bi-phase, NRZ-M

Output LINE-CODE signal +/-2Vp-p

Master Signals:

Output Frequencies carrier: 100kHz in quadrature and a third digital signal

sample clock 8.333kHz (sub-multiple of the carrier)

message: 2.083kHz sinusoidal and digital,

Output Levels 4V pk-pk, analog (+/- 5%)

Digital level, 0V to 5V


3 independent dual input multipliers

Bandwidth approx 600kHz

Characteristic k.X(t).Y(t)

k approx 1

Noise Generator:

Bandwidth 10Hz to < 240kHz, "white" noise

Maximum level approx 4.8Vrms

Attenuator steps 0dB (approx 4.8Vrms), -6dB (approx 2.4Vrms)

and -20dB (approx 0.48Vrms)

PCM Encoder:

Input Vin +/-2Vpk, DC coupled

Bit Clock Input >128kHz, digital-level

Output Signal serial, digital-level data stream in offset binary format

Output Format 8 bits data

Frame Synchronization FS synchronization signal coincident with frame’s LSB

TDM Mode two input Time Division Multiplex system

No anti-aliasing filters

PCM Decoder:

Input PCM DATA serial, digital-level data stream in offset binary format

Input Format 8 bits

Bit Clock Input <128kHz, digital-level;

Output Signal approximately +/-2Vpk, DC coupled

TDM Mode two channel TDM system

Outputs do no include reconstruction filters

Phase Shifter:

Bandwidth > 200kHz

Frequency Ranges two regions

HI approx. 100kHz;

LO approx. 2kHz

Auto detect HI/LO boundary approx. 40kHz

Sequence Generator:

Input Clock Range TTL 1Hz to 100kHz

Number of Sequences 2: X and Y

Sequence Lengths X = 31 bits, Y = 255 bits

Sync indicates start of sequence X

Serial to Parallel:

Inputs SERIAL digital-level data;

CLK is the digital-level clock signal;

Maximum CLK Rate approx 100kHz

Outputs bipolar parallel data output


Microphone electret-type with frequency response of 300Hz to 3kHz

Output typically 0.6 Vrms

Tunable LPF

Filter Range 600 Hz to 12 kHz

Filter Order 8th order, Elliptic

Stopband Attenuation > -50dB at 1.4 fc and Passband Ripple < 0.5dB

Gain Control 0 to 1.6

Twin Pulse Generator:

Clock Frequency Range < 8kHz

Pulse WIDTH 5us < tw < 40us

Pulse DELAY Q2-Q1 50us < td < 300us



Operating Range > 100kHz

TTL Output Risetime 500nsec (typically)


Bandwidth DC to 100kHz (approx)


LPF -3dB 2.6kHz (approx)


LPF -3dB 2.6kHz (approx)

System Specifications


All front panel controls can be varied either manually or via PC-control.

PC-control can only be implemented by NI LabVIEW and DAQmx interface via NI ELVIS edge connector

PC-control software interfaces:

DATEx SFP, DATEx Toolbar SFP and DATEx low level VIs


Patch Cords 20 x 2mm-2mm stackable patch cords

Scope leads 3 x 2mm-to-BNC coaxial oscilloscope leads

DMM leads 2 x 2mm-to-4mm patch cords

Headphones 1 x lightweight stereo headphones,

24ohm, 3.5mm male stereo plug

Documentation 1 x User Manual; 1 x Experiment Manual


Input impedance: 50kohm

Output impedances:

Analog signals: 330 ohm

Digital signals: 47 ohm

Maximum allowable input voltage: +/- 12V

Maximum output voltage : +/- 12V


Power Source supplied via NI ELVIS edge connector

+5, +15, -15 rails consume <200mA each


Operating Temperature Range 10 to 30 degrees C

Storage Temperature Range 5 to 40 degrees C

Humidity up to 90% RH, non-condensing


Dimensions front panel 280 x 215mm;


Additional Resources

Product Page: NI ELVIS II/Emona Telecommunications Bundle
NI ELVIS Telecommunication Education Resource Page

Emona ETT-202 DATEx for NI ELVIS FAQ: Part 1
Emona ETT-202 DATEx for NI ELVIS FAQ: Part 2
Emona ETT-202 DATEx for NI ELVIS FAQ: Part 3

Was this information helpful?