Complete the following steps to connect the cRIO-9037 to the host computer using the USB device port. Power on the host computer. Connect the cRIO-9037 to the host computer using the USB A-to-B cable. ...

Complete the following steps to connect the cRIO-9037 to a wireless network. Launch MAX on the host computer. Expand Remote Systems in the configuration tree and locate your system. Select your target. ...

Ensure that the USB connections between the cRIO-9037 and the host computer and the Ethernet connections between the host computer and the router are secure. Configure the IP and other network settings ...

Complete the following steps to connect the cRIO-9037 to a wireless network. Launch MAX on the host computer. Expand Remote Systems in the configuration tree and locate your system. Select your target. ...

Complete the following steps to set a system password. Note The default username for the cRIO-9036 is admin . There is no default password for the cRIO-9036 , so you must leave the password field blank ...

The following table describes the STATUS LED indicators. Table 3. STATUS LED Indicators LED Color LED Pattern Indication Yellow Blinks twice and pauses The cRIO-9036 is in safe mode. Software is not installed, ...

Software is licensed pursuant to the software license agreements provided with the software or, in the absence of such license agreements, the National Instruments Software License Agreement available ...

The following figure shows the reset behavior of the cRIO-9036 . Figure 3. Reset Button Behavior Press and hold RESET button fo r ≥ 5 s Press and hold RESET button for < 5 s Run Mode Safe Mode Press

Notice To prevent electrostatic discharge (ESD) from damaging the device, ground yourself using a grounding strap or by holding a grounded object, such as your computer chassis. Touch the antistatic package ...

Put the cRIO-9036 in safe mode and enable the RS-232 serial port by holding the RESET button down for 5 seconds. The STATUS LED starts blinking three times every few seconds. Use the RS-232 serial port ...

Verify that the following items are included in the cRIO-9036 kit. Parent topic: Overview Parent topic: GSG Purpose (cRIO/sbRIO)

This document lists the specifications for the National Instruments cRIO-9036 . The following specifications are typical for the -40 °C to 70 °C operating temperature range unless otherwise noted. Caution ...

This document describes how to begin using the National Instruments cRIO-9038 . In this document, the NI cRIO-9038 and NI cRIO-9038 Sync are inclusively referred to as the cRIO-9038 . For more information ...

Complete the following steps to install a C Series module. 3 2 2 1 1: 1: P P O O W W E E R R 2 2 : S : S T T A A T T US US

You must install a ferrite around all USB cables connected to the USB host ports to ensure that the cRIO-9037 meets all EMC standards applicable to your country.

Before using the cRIO-9037 , you must install the following application software and device drivers on the host computer in this order: LabVIEW 2015 SP1 or later LabVIEW Real-Time Module 2015 SP1 or later ...

Some products are approved for marine (shipboard) applications. To verify marine approval certification for a product, visit ni.com/product-certifications , search by model number, and click the appropriate ...

When you power on the cRIO-9037 for the first time, the device boots into safe mode. The POWER LED illuminates, the STATUS LED illuminates briefly, and then the STATUS LED blinks twice every few seconds. ...

Ensure that the environment in which you are using the cRIO-9037 meets the following specifications. Operating temperature (IEC 60068-2-1, IEC 60068-2-2) -20 °C to 55 °C Operating humidity (IEC 60068-2-78) ...

Verify that power is not connected to the I/O connector(s) on the C Series module before you remove a module from the cRIO-9037 . If the system is in a nonhazardous location, the cRIO-9037 can be powered ...

The cRIO-9037 is suitable for use in Class I, Division 2, Groups A, B, C, D, T4 hazardous locations; Class I, Zone 2 , AEx nA IIC T4 Gc and Ex nA IIC T4 Gc hazardous locations; and nonhazardous locations ...

Caution Observe all instructions and cautions in the user documentation. Using the model in a manner not specified can damage the model and compromise the built-in safety protection. Return damaged models ...

Complete the following steps to set a system password. Note The default username for the cRIO-9037 is admin . There is no default password for the cRIO-9037 , so you must leave the password field blank ...

The cRIO-9037 has been evaluated as Ex nA IIC T4 Gc equipment under DEMKO 12 ATEX 1202658X and is IECEx UL 14.0089X certified. Each device is marked II 3G and is suitable for use in Zone 2 hazardous locations, ...

The following table describes the STATUS LED indicators. Table 3. STATUS LED Indicators LED Color LED Pattern Indication Yellow Blinks twice and pauses The cRIO-9037 is in safe mode. Software is not installed, ...

Visit ni.com/support to find support resources including documentation, downloads, and troubleshooting and application development self-help such as tutorials and examples. Visit ni.com/services to learn ...

The following figure shows the reset behavior of the cRIO-9037 . Figure 4. Reset Button Behavior Press and hold RESET button fo r ≥ 5 s Press and hold RESET button for < 5 s Run Mode Safe Mode Press

181-210 de 277951 résultats
7 de 9266 pages