APPLICATION SUPPORT S e r v i ce s n i . c o m / s e r v i c e s NI Community n i . c o m/community NI CompactRIO Developer’s Guide Software Support ni.com/info »

Complete the following steps to install a C Series module. 2 2 3 1 Verify that power is not connected to the I/O connector(s) on the C Series module. If the system is in a nonhazardous location, the cRIO-9064 ...

Some products are approved for marine (shipboard) applications. To verify marine approval certification for a product, visit ni.com/product-certifications , search by model number, and click the appropriate ...

Ensure that the USB connections between the cRIO-9064 and the host computer and the Ethernet connections between the host computer and the router are secure. Configure the IP and other network settings ...

This product was tested and complies with the regulatory requirements and limits for electromagnetic compatibility (EMC) stated in the product specifications. These requirements and limits provide reasonable ...

Notice To prevent electrostatic discharge (ESD) from damaging the device, ground yourself using a grounding strap or by holding a grounded object, such as your computer chassis. Touch the antistatic package ...

Put the cRIO-9063 in safe mode and enable the RS-232 serial port by holding the RESET button down for 5 seconds. The STATUS LED starts blinking three times every few seconds. Use the RS-232 serial port ...

Definitions Warranted specifications describe the performance of a model under stated operating conditions and are covered by the model warranty. Characteristics describe values that are relevant to the ...

Complete the following steps to install a C Series module. 2 2 3 1 Verify that power is not connected to the I/O connector(s) on the C Series module. If the system is in a nonhazardous location, the cRIO-9066 ...

Complete the following steps to install software on the cRIO-9066 . In MAX, expand your system under Remote Systems. Right-click Software . Select Add/Remove Software to launch the LabVIEW Real-Time Software ...

Before using the cRIO-9066 , you must install the following application software and device drivers on the host computer in this order: LabVIEW 2014 or later LabVIEW Real-Time Module 2014 or later LabVIEW ...

Some products are approved for marine (shipboard) applications. To verify marine approval certification for a product, visit ni.com/product-certifications , search by model number, and click the appropriate ...

When you power on the cRIO-9066 for the first time, the device boots into safe mode. The POWER LED illuminates, the STATUS LED illuminates briefly, and then the STATUS LED blinks twice every few seconds. ...

Ensure that the environment in which you are using the cRIO-9066 meets the following specifications. Operating temperature (IEC 60068-2-1, IEC 60068-2-2) -20 °C to 55 °C Operating humidity (IEC 60068-2-78) ...

Verify that power is not connected to the I/O connector(s) on the C Series module before you remove a module from the cRIO-9066 . If the system is in a nonhazardous location, the cRIO-9066 can be powered ...

The cRIO-9066 is suitable for use in hazardous locations; , and hazardous locations; and nonhazardous locations only. Follow these guidelines if you are installing the cRIO-9066 in a potentially explosive ...

Caution Observe all instructions and cautions in the user documentation. Using the model in a manner not specified can damage the model and compromise the built-in safety protection. Return damaged models ...

Complete the following steps to set a system password. Note The default username for the cRIO-9066 is admin . There is no default password for the cRIO-9066 , so you must leave the password field blank ...

The cRIO-9066 has been evaluated as equipment under DEMKO ATEX and is IECEx certified. Each device is marked and is suitable for use in Zone 2 hazardous locations, in ambient temperatures of -20 °C ≤ Ta ...

The following table describes the STATUS LED indicators. Table 3. STATUS LED Indicators LED Pattern Indication Blinks twice and pauses The cRIO-9066 is in safe mode. Software is not installed, which is ...

Complete the following steps to find the system in MAX. Launch MAX on the host computer. Expand Remote Systems in the configuration tree and locate your system. Select your target. Tip MAX lists the system ...

Add an exception for MAX to your network firewall or other security software by completing the following steps: On Windows 7, select Start » Control Panel » System and Security » Windows Firewall » Allow ...

You must connect the cRIO-9066 grounding terminal to the grounding electrode system of the facility. What to Use Ring lug Wire, 2.1 mm 2 ( 14 AWG ) or larger Screwdriver, Phillips #2 What to Do Complete ...

The cRIO-9066 has the following connectors, LEDs, and buttons. Parent topic: Overview Parent topic: GSG Purpose (cRIO/sbRIO)

Complete the following steps to connect the cRIO-9066 to the host computer using the USB device port. Power on the host computer. Connect the cRIO-9066 to the host computer using the USB A-to-B cable. ...

The cRIO-9066 requires a 9 V to 30 V external power supply. The cRIO-9066 filters and regulates the supplied power and provides power for the C Series modules. The cRIO-9066 has one layer of reverse-voltage ...

Ensure that the USB connections between the cRIO-9066 and the host computer and the Ethernet connections between the host computer and the router are secure. Configure the IP and other network settings ...

This product was tested and complies with the regulatory requirements and limits for electromagnetic compatibility (EMC) stated in the product specifications. These requirements and limits provide reasonable ...

271-300 de 277951 résultats
10 de 9266 pages