Filtered Results

Conditions Specifications are typical and valid from -40 °C to +85 °C unless otherwise noted. Input Characteristics Number of channels 8 analog input channels Isolation Galvanic isolation between channels ...

Conditions Specifications are typical and valid from -40 °C to +85 °C unless otherwise noted. Input Characteristics Number of channels 8 analog input channels Isolation Galvanic isolation between channels ...

Conditions Specifications are typical and valid from -40 °C to +85 °C unless otherwise noted. Input Characteristics Number of channels8 analog input channelsIsolation Galvanic isolation between channels ...

Conditions Specifications are typical and valid from -40 °C to +85 °C unless otherwise noted. Input Characteristics Number of channels 8 analog input channels Isolation Galvanic isolation between channels ...

Conditions Specifications are typical and valid from -40 °C to +85 °C unless otherwise noted. Input Characteristics Number of channels 8 analog input channels Isolation Galvanic isolation between channels ...

You can use the FieldDAQ device as expansion I/O from certain NI Linux Real-Time controllers. Discover and configure the NI Linux Real-Time controller in NI MAX, then discover and configure the FieldDAQ ...

Use this branch for devices with minimum NI-DAQmx support <=18.0: FD-11603/11613/11637 The onboard 100 MHz oscillator automatically synchronizes to other network-synchronized devices that are part of your ...

Recommended networking topologies are described in this section. Host—Can be a Windows computer or a real-time controller with the NI Linux Real-Time operating system, such as the IC-317x, cRIO-9035/9039 ...

8-Channel, ±10 V Powered-Sensor Voltage Input Device for FieldDAQ Connect directly to amplified sensors with built-in, configurable sensor power Built-in signal conditioning and filtering for accurate ...

Front PanelPower IN ConnectorPower LEDEthernet Port 0 and LEDBank 1 Voltage Input Connectors 0 through 3 and LEDsBank 2 Voltage Input Connectors 0 through 3 and LEDsMounting HolesPower OUT ConnectorSTATUS ...

8-Channel, ±10 V Voltage Input Device for FieldDAQ Built-in signal conditioning and filtering for accurate voltage measurements Rugged, water-resistant, and dust-proof design with shock and vibration resistance ...

Front PanelPower IN ConnectorPower LEDEthernet Port 0 and LEDBank 1 Voltage Input Connectors 0 through 3 and LEDsBank 2 Voltage Input Connectors 0 through 3 and LEDsMounting HolesPower OUT ConnectorSTATUS ...

8-Channel, ±60 V Voltage Input Device for FieldDAQ Built-in signal conditioning and filtering for accurate high voltage measurements Rugged, water-resistant, and dust-proof design with shock and vibration ...

Use this topic version for devices supported in NI-DAQmx 18.1 or earlier. A sample consists of one reading from each channel in the AI task. Sample Clock signals the start of a sample of all analog input ...

Use the Start Trigger signal to begin a measurement acquisition. A measurement acquisition consists of one or more samples. If you do not use triggers, begin a measurement with a software command. Once ...

You can use time as a trigger for sync pulses on the FieldDAQ device. To use a sync pulse with a time source, specify a specific time in NI-DAQmx. Refer to the Time Triggering topic in the NI-DAQmx Help ...

The cDAQ-9185/9189 and FieldDAQ Firmware FOSS Notices (NI part number 377121x-01) document contains information about open source code use and software licenses for FieldDAQ firmware versions. To view ...

Unpacking What You Need to Get Started Wiring External Power to the FieldDAQ Device Setting up the FieldDAQ Device Connecting to a Real-Time Controller Troubleshooting Device Connectivity Reserving the ...

In a line topology—also known as daisy-chaining or bus topology—the host communicates directly with all nodes through one bus line. A standard Ethernet device or switch can be added to the end of the chain ...

If you need to clean your device, wipe it with a dry towel. M12 connectors must be mated to cables or have caps installed on them to meet IP requirements. Cover the unused connectors with the included ...

The following documents will help you overcome typical hurdles in getting started with synchronized measurements: Synchronizing analog input FieldDAQ devices with NI-DAQmx in LabVIEW—Visit ni.com/info ...

You can use the FieldDAQ device in the following analog input applications: Finite acquisition Continuous acquisition The FieldDAQ device features the following timing and triggering signals: AI Sample ...

To reset your FieldDAQ device to factory-default settings, complete the following steps. Verify the power source is turned off. Connect Ethernet port 0 and port 1 with an Ethernet cable. Connecting Port ...

In a ring topology, the host communicates with all nodes through the most effective path. You must use an external switch in a ring topology. You must configure the network properly with a recommended ...

In a star topology, the host communicates directly with each node through the external switch. You must use an external switch in a star topology; for network synchronization, you must use an external ...

Front PanelPower IN ConnectorPower LEDEthernet Port 0 and LEDBank 1 Voltage Input Connectors 0 through 3 and LEDsBank 2 Voltage Input Connectors 0 through 3 and LEDsMounting HolesPower OUT ConnectorSTATUS ...

1-30 de 71 résultats
1 de 3 pages