Filtered Results

Conditions Specifications are typical and valid at -40 °C to 85 °C unless otherwise noted. Input Characteristics Number of channels8 analog input channelsIsolation Galvanic isolation between channels and ...

Conditions Specifications are typical and valid at -40 °C to 85 °C unless otherwise noted. Input Characteristics Number of channels8 analog input channelsIsolation Galvanic isolation between channels and ...

You can use the FieldDAQ device as expansion I/O from certain NI Linux Real-Time controllers. Discover and configure the NI Linux Real-Time controller in NI MAX, then discover and configure the FieldDAQ ...

The onboard 100 MHz oscillator automatically synchronizes to other network-synchronized devices that are part of your local IEEE 802.1AS subnet. The 13.1072 MHz, 12.8 MHz, 12.288 MHz, and 10.24 MHz Timebases ...

Recommended networking topologies are described in this section. Host—Can be a Windows computer or a real-time controller with the NI Linux Real-Time operating system, such as the IC-317x, cRIO-9035/9039 ...

8-Channel Sound and Vibration Input Device for FieldDAQ Multiple input ranges with 24-bit resolution and 102.4 kSamples/s for the most accurate microphone and accelerometer measurements Built-in IEPE signal ...

Front PanelPower IN ConnectorPower LEDEthernet Port 0 and LEDBank 1 Input Connectors 0 through 3 and LEDsBank 2 Input Connectors 0 through 3 and LEDsMounting HolesPower OUT ConnectorSTATUS LEDEthernet ...

The cDAQ-9185/9189 and FieldDAQ Firmware FOSS Notices (NI part number 377121x-01) document contains information about open source code use and software licenses for FieldDAQ firmware versions. To view ...

Unpacking What You Need to Get Started Wiring External Power to the FieldDAQ Device Setting up the FieldDAQ Device Connecting to a Real-Time Controller Troubleshooting Device Connectivity Reserving the ...

In a line topology—also known as daisy-chaining or bus topology—the host communicates directly with all nodes through one bus line. A standard Ethernet device or switch can be added to the end of the chain ...

If you need to clean your device, wipe it with a dry towel. M12 connectors must be mated to cables or have caps installed on them to meet IP requirements. Cover the unused connectors with the included ...

The following documents will help you overcome typical hurdles in getting started with synchronized measurements: Synchronizing analog input FieldDAQ devices with NI-DAQmx in LabVIEW—Visit ni.com/info ...

To reset your FieldDAQ device to factory-default settings, complete the following steps. Verify the power source is turned off. Connect Ethernet port 0 and port 1 with an Ethernet cable. Connecting Port ...

In a ring topology, the host communicates with all nodes through the most effective path. You must use an external switch in a ring topology. You must configure the network properly with a recommended ...

To find information about the pinout, signal descriptions, and LED indicators on your FieldDAQ device, refer to the Front Panel topic for your Model. Model features may differ. Connecting Input Signals ...

In a star topology, the host communicates directly with each node through the external switch. You must use an external switch in a star topology; for network synchronization, you must use an external ...

Never touch the exposed pins of connectors. To avoid ESD damage in handling the device, take the following precautions: Ground yourself with a grounding strap or by touching a grounded object. Touch the ...

8-Channel Sound and Vibration Input Device for FieldDAQ Multiple input ranges with 24-bit resolution and 102.4 kSamples/s for the most accurate microphone and accelerometer measurements Built-in IEPE signal ...

Front PanelPower IN ConnectorPower LEDEthernet Port 0 and LEDBank 1 Input Connectors 0 through 3 and LEDsBank 2 Input Connectors 0 through 3 and LEDsMounting HolesPower OUT ConnectorSTATUS LEDEthernet ...

To find information about the pinout, signal descriptions, and LED indicators on your FieldDAQ device, refer to the Front Panel topic for your Model. Model features may differ. Connecting Input Signals ...

You can configure the FieldDAQ device for either AC or DC coupling in software. DC coupling—Passes any DC offset present in the source signal to the ADC. Choose this configuration when the signal source ...

Complete the following steps. Install the application software (if applicable), as described in the installation instructions that accompany your software. Check your driver and application development ...

The following figure shows the FD-116xx clock routing circuitry and timebases. Clock Routing Circuitry You can use the 13.1072 MHz, 12.8 MHz, 12.288 MHz, and 10.24 MHz timebases to generate the AI Sample ...

If your FieldDAQ device becomes disconnected from the network, open MAX and try the following: After moving the device to a new network, NI-DAQmx may lose connection to the device. In this case, click ...

The FieldDAQ device requires an external power source as described in the Power Requirements of the specifications document. The POWER LED identifies when the device is receiving adequate power for its ...

Complete the following steps. Install the application software (if applicable), as described in the installation instructions that accompany your software. Check your driver and application development ...

The maximum operating temperature of 85 °C may be reduced for any mounting configuration other than the reference mounting configuration. A 10 °C (18 °F) reduction in maximum operating temperature is sufficient ...

You can connect TEDS (Transducer Electronic Data Sheets) sensors to the FieldDAQ device through the AI+ and AI- pins on each connector.

You can use the 13.1072 MHz, 12.8 MHz, 12.288 MHz, and 10.24 MHz timebases to generate data rates. The FD-116xx supports data rates (f[s]) between 500 Samples/s and 102.4 kSamples/s. By default, NI-DAQmx ...

The Ethernet Network Interface transfers data between the FieldDAQ device and the network. It gathers the data into TCP/IP packets that can be sent across the network and interpreted by the host. The FieldDAQ ...

1-30 de 55 résultats
1 de 2 pages