From Friday, April 19th (11:00 PM CDT) through Saturday, April 20th (2:00 PM CDT), 2024, ni.com will undergo system upgrades that may result in temporary service interruption.
We appreciate your patience as we improve our online experience.
From Friday, April 19th (11:00 PM CDT) through Saturday, April 20th (2:00 PM CDT), 2024, ni.com will undergo system upgrades that may result in temporary service interruption.
We appreciate your patience as we improve our online experience.
2015 f2 Bug Fixes
The following list describes issues in previous versions of the NI Vision Builder for Automated Inspection that are fixed in the 2015 f2 update.
ID | Fixed Issue |
---|---|
617482, 629760 | On NI CVS-1458RT, IC-3120, and IC-317x Linux Real-Time targets, Ethernet interfaces do not always enumerate with the expected name order upon boot. |
608370, 629758 | On NI CVS-1458RT, IC-3120, and IC-317x Linux Real-Time targets, communication with the host does not by default get sent out the primary/host Ethernet port if the host and other devices are all connected with link-local addressing (LLA). |
626575, 629757 | On NI CVS-1458RT, IC-3120, and IC-317x Linux Real-Time targets, devices connected with link-local addressing (LLA) can sometimes obtain duplicate IP addresses upon link negotiation. |
2015 f1 Bug Fixes
The following list describes issues in previous versions of the NI Vision Builder for Automated Inspection that are fixed in the 2015 f1 update.
ID | Fixed Issue |
---|---|
562981 | On real-time targets, timestamp metadata from acquired images may have the UTC offset incorrectly applied to them. |
572339 | You must install Industrial Controller Device Drivers to discover industrial controller targets in LabVIEW projects and to access their shared variables. |
576529 | Vision Builder AI can sometimes hang when exiting the Calculator step. |
577667 | Geometry step results may be mismatched when referring to missing measurements from a previous step. |
583042 | Network drive mounting on Linux RT targets is not successful if /mnt folder does not exist. |
587709 | The Detect Defects step returns a larger defect area than expected when regions to ignore are added to the template and then later removed. |
591218 | You cannot set a password for Configuration Interface access. |
2015 Bug Fixes
The following list describes issues in previous versions of the NI Vision Builder for Automated Inspection that are fixed in the 2015 release.
ID | Fixed Issue |
---|---|
353860 | In the Calculator step, the AltGr key cannot be used to input symbols into a formula node. |
429533 | Color calibrated images are converted to monochrome when saved to file. |
507095, 570862 | The Run LabVIEW VI step sometimes shows a dialog to update other steps in cases where it is not needed. |
518331 | The 1D Barcode step does not handle the Validate option correctly when multiple barcode types are used in a single step. Some types do not support validation. |
520201 | The Run LabVIEW VI step does not let you set a latched Boolean. |
523349 | The Read/Write Variables to INI File step can sometimes swap values for variables with similar names. |
527484 | The Run LabVIEW VI step sometimes does not update references when files have changed on the disk since last load. |
538617 | Image acquisition timeout received when multiple states in the inspection contain acquisition steps with different window sizes or positions. |
541229 | The Run LabVIEW VI step does not allow you to use relative paths when the only common portion of the path is the root of the drive. |
542652 | Inspections do not give a save prompt when migrated between 32-bit and 64-bit instances of Vision Builder AI. |
542944 | Setting a password on a CVS-1457RT blocks access to the target from 64-bit Vision Builder AI applications. |
545859 | In the Acquire Image step, the camera name as seen in MAX is not visible when selecting cameras. |
549194 | After generating LabVIEW VIs with Vision RIO steps, the hardware state is not properly reflected in the Vision RIO test panel. |
552394 | The transition dialog for a state does not allow you to select a specific numeric value greater than 0 if the dialog was using a previous measurement result as the comparison value. |
552682 | System images created for Linux RT-based Compact Vision Systems cannot be redeployed to those targets. |
552910 | The Run LabVIEW VI step does not fail after you rename indicators which are used to set inspection variables. |
553921 | In the Calculator step, controls placed inside a structure do not correctly pass on their values. |
563565 | The context help window can get stuck in a state where it fails to close when expected or to update its content. |
564701 | The system variable Memory Usage reports 0 MB on RT targets. |
565038, 565142 | Extracting part of a calibrated image can return negative areas for particles. |
565352 | A VI resetting dialog is sometimes shown when closing Vision Builder AI. |
568678 | The system variable Device Name does not get properly set on Linux RT targets. |
568683 | Linux RT targets sometimes show inconsistent IP addresses between the Global Variable Manager and the targets' Network Configuration dialog. |
568943 | Large inspections can sometimes return that an error occurred at an unidentified location. |
569019 | Custom steps using advanced math cannot run on Linux RT targets. |
569425 | The NI-DAQmx I/O Test Panel and Monitor cannot set the radix representation (decimal or hexadecimal) of the output port's value. |
569638 | Keyboard shortcuts which close VI diagram windows can accidentally be used in the Calculator step and Custom Inspection Interface in 64-bit instances of Vision Builder AI. |
569658 | Some Vision Assistant steps which modify images incorrectly restrict you from changing the ROI in subsequent steps. |
570861 | Migrating the Run LabVIEW VI step from a previous version of Vision Builder AI returns an error regarding copying files to nonexistent paths. |
571282 | The FTP server is not available for use on Linux RT targets. To use this feature in Vision Builder AI 2015, you must install a recommended software set for Vision Builder AI to the target from MAX, and select the Legacy FTP Server as an optional add-on. |
574248 | When modifying execution flow, copies of other steps can unexpectedly replace inspection steps. |