ECU Test System Maintenance Software 21.0 Known Issues

Información general

This document contains the ECU Test System Maintenance Software known issues that were discovered before and since the release of ECU Test System Maintenance Software 21.0. Known issues are performance issues or technical bugs that NI has acknowledged exist within this version of the product.

 

Not every issue known to NI appears on this list; it is intended to show the most severe and common issues that you may encounter and provide workarounds when possible. Other technical issues that you may encounter could occur through normal product use or system compatibility issues. You may find more information on these issues in NI’s Product Documentation, Knowledgebase, or Community.

Bug Number

Legacy ID

Description

Details

1259280

Running the Reset operation does not reset automotive Ethernet instruments

Running the Reset operation does not reset automotive Ethernet instruments.

Workaround:

Reset Automotive Ethernet instruments using NI MAX.

Reported Version:

ECU Test System Maintenance Software 21.0.0

Resolved Version:

N/A

Added:

Mar 9, 2021

1265074

Running the Reset operation does not reset SLSC modules

Running the Reset operation does not reset SLSC modules.

Workaround:

Reset the SLSC chassis to reset the SLSC modules.

Reported Version:

ECU Test System Maintenance Software 21.0.0

Resolved Version:

N/A

Added:

Mar 9, 2021

1421236

NI MAX may show the PXIe-8430/8 serial module outside of the chassis on first boot

In systems that ship with a serial module, NI MAX may show the PXIe-8430/8 serial module outside of the chassis on first boot.

Workaround:

Restart the ECU Test System.

Reported Version:

ECU Test System Maintenance Software 21.0.0

Resolved Version:

N/A

Added:

Apr 16, 2021

1421227

Systems with a second PXI chassis may show the Thunderbolt device disconnected on first boot

In systems that ship with a second PXI chassis, the Thunderbolt expansion MXI (PXIe-8301) may not be recognized as connected to the system. NI MAX does not show the secondary chassis, and the devices associated with that chassis show as missing from the system.

Workaround:

Shut down and power off the ECU Test System. Leave powered off for one minute before powering on the system again. If the second chassis is still not detected, use the Thunderbolt software from the notification area to recognize and authorize the port.

Reported Version:

ECU Test System Maintenance Software 21.0.0

Resolved Version:

N/A

Added:

Apr 17, 2021

1329655

Terminal blocks are incorrectly labeled as cables in failure messages

Failure messages in the report may label terminal block components as cables.

Workaround:

There is currently no known workaround for this issue.

Reported Version:

ECU Test System Maintenance Software 21.0.0

Resolved Version:

ECU Test System Maintenance Software 21.0.1

Added:

Apr 15, 2021

1211012

ECUTS-16000/16001 User Manual shows incorrect pins in the J18, J19, J20, and J21 pin map when populated with a PXIe-6378

4 ground pins are incorrect: B39, A45, B45, and B47.

Workaround:

The pins should be mapped as follows:
  • B39 = DGND
  • A45 = DGNDP0.0_P0.1
  • B45 = DGNDP1.0_P1.1
  • B47 = DGND

Reported Version:

ECU Test System Maintenance Software 21.0.0

Resolved Version:

ECU Test System Maintenance Software 21.0.1

Added:

Apr 15, 2021

1364766

Disconnected load wires are not always detected for RMX-4005 devices

If an RMX-4005 is just connected to only one set of Load wires, the ECU Test System Maintenance Software's continuity check with a Field Diagnostic Tester (FDT) may incorrectly pass.

Workaround:

There is currently no known workaround for this issue.

Reported Version:

ECU Test System Maintenance Software 21.0.0

Resolved Version:

ECU Test System Maintenance Software 21.0.1

Added:

Apr 15, 2021

Final Time Issue Listed

Issues found in this section will not be listed in future known issues documents for this product.

There are currently no issues to list.

Additional Resources

Explore Support Content and Product Documentation 

 

 

Ask the NI Community

 

 

Request Support from an Engineer

 

A valid service agreement may be required, and support options vary by country

 

Glossary of Terms

 

  • Bug ID - When an issue is reported to NI, you may be given this ID or find it on ni.com.  You may also find IDs posted by NI on the discussion forums or in KnowledgeBase articles.
  • Legacy ID – An older issue ID that refers to the same issue.  You may instead find this issue ID in older known issues documents.
  • Description - A few sentences which describe the problem. The brief description given does not necessarily describe the problem in full detail.
  • Workaround - Possible ways to work around the problem.
  • Reported Version - The earliest version in which the issue was reported.
  • Resolved Version - Version in which the issue was resolved or was no longer applicable. "N/A" indicates that the issue has not been resolved.
  • Date Added - The date the issue was added to the document (not the reported date).