This document contains the InstrumentStudio known issues that were discovered before and since the release of InstrumentStudio 2022 Q4. Known issues are performance issues or technical bugs that NI has acknowledged exist within this version of the product.
Not every issue known to NI appears on this list; it is intended to show the most severe and common issues that you may encounter and provide workarounds when possible. Other technical issues that you may encounter could occur through normal product use or system compatibility issues. You may find more information on these issues in NI’s Product Documentation, Knowledgebase, or Community; see Additional Resources.
|
Bug Number |
Legacy ID |
Description |
Details |
|---|---|---|---|
| 388174 | 692303 |
Devices Are Duplicated When Putting the Chassis to Sleep After Selecting Auto-Create LayoutIf you create an Auto Layout then put the chassis to sleep while InstrumentStudio is running, InstrumentStudio creates duplicate instances of each device when you wake the chassis up from sleep. Workaround: There is currently no known workaround for this issue. |
Reported Version: InstrumentStudio 2018 Resolved Version: N/A Added: Jun 3, 2018 |
| 388162 | 691516 |
Devices Go Missing After Waking the Host From Sleep When InstrumentStudio Is RunningIf you put the host into sleep mode while InstrumentStudio is running, devices sometimes go missing in InstrumentStudio when you wake the computer. Workaround: There is currently no known workaround for this issue. |
Reported Version: InstrumentStudio 2018 Resolved Version: N/A Added: May 27, 2018 |
| 1154387 |
Digital Trigger Sources Do Not Update After Renaming a Device in MAXIf you rename an Oscilloscope device in MAX, the new name will not automatically appear in the list of digital trigger sources in the InstrumentStudio Oscilloscope panel. After renaming one or more devices, errors occur when attempting to use those digital trigger sources.
Workaround: Select a different trigger type in the InstrumentStudio Oscilloscope panel and then select Digital triggering again. This will force the list of trigger sources to refresh.
|
Reported Version: InstrumentStudio 2019 Resolved Version: N/A Added: Oct 22, 2021 |
|
| 1063539, 992871 |
Pins Using Multiplexed Connections Are Not Shown Under the Correct Site in InstrumentStudioInstrumentStudio does not currently support multiplexed connections in pin maps. If the site filter is set to a specific site, pins under that site will not appear in the panel if they are mapped in the pin map using multiplexed connections. The channels using multiplexed connections will appear under Unmapped channels if the Site filter is set to All sites, but will not display the pin names from the pin map. Workaround: There is currently no known workaround for this issue.
|
Reported Version: InstrumentStudio 2019 Resolved Version: N/A Added: Oct 22, 2021 |
|
| 1067929 |
SMU Waveform Mode May Not Graph Data for All Selected Channels With High Capture TimesWhen multiple channels are enabled in SMU Waveform mode and selected for display on the graph, InstrumentStudio may fail to acquire waveform data for all of the selected channels when you increase the capture time, depending on the channel count and capture time used.
Workaround: Reduce the capture time or limit the number of channels you are acquiring data from.
|
Reported Version: InstrumentStudio 2019 Resolved Version: N/A Added: Oct 22, 2021 |
|
| 1176443 |
Installing a Previous Version of InstrumentStudio Causes All Project Files to Open With the Most Recently Installed VersionProject files will open with the most recently installed version of InstrumentStudio. For example, if you install InstrumentStudio 2020, create and save projects in that version, and then install InstrumentStudio 2019, the project files created in InstrumentStudio 2020 will open by default with InstrumentStudio 2019. InstrumentStudio projects and documents are not backward-compatible, so the project will give an error saying that it failed to load.
Workaround: Change the Windows file association for .instudioproj files to the latest version or repair the InstrumentStudio installation with the desired default project version.
|
Reported Version: InstrumentStudio 2018 SP2 Resolved Version: N/A Added: Oct 22, 2021 |
|
| 1371988 |
SMU/Power "Export To TestStand" Measure When property in exported IO Configuration is different before and after running the panelThe IO Configuration generated when clicking on "Export to TestStand" in an SMU/Power Supply panel will be different before and after running the panel. Specifically, the "Measure When" (NIDCPOWER_ATTR_MEASURE_WHEN) property will have different values:
This will affect results if used in read measurement steps within TestStand. Workaround: There is currently no known workaround for this issue. |
Reported Version: InstrumentStudio 2020 Resolved Version: N/A Added: Oct 22, 2021 |
Issues found in this section will not be listed in future known issues documents for this product.
There are currently no issues to list.
Explore Support Content and Product Documentation
Ask the NI Community
Request Support from an Engineer
A valid service agreement may be required, and support options vary by country