Filtered Results

Creates channel(s) that use a thermistor to measure temperature. Use this instance when the thermistor requires current excitation. You must configure the physical channel(s) with TEDS information to use ...

Creates channel(s) that use an RTD to measure temperature. You must configure the physical channel(s) with TEDS information to use this VI. LabVIEW NXG does not support FPGA devices Not supported in VIs ...

Creates channel(s) that use a thermocouple to measure temperature. You must configure the physical channel(s) with TEDS information to use this VI. LabVIEW NXG does not support FPGA devices Not supported ...

Creates a virtual channel, or set of virtual channels, and adds them to a task. You must configure the physical channel(s) with TEDS information to use this node. If you use this node within a loop without ...

Creates channel(s) that use a Wheatstone bridge to measure torque. You must configure the physical channel(s) with TEDS information to use this VI. NI-DAQmx scales electrical values to physical values ...

Creates a timing source for a Timed Loop. The timing source is based on signals a device generates. Timing sources send ticks to a timed loop. Those ticks determine when the Timed Loop executes. By default, ...

Creates a timing source that uses the signal you specify to determine when to send ticks to a Timed Loop. You must create a task that can generate the signal and wire that task to the task/channels in ...

Creates and configures a task that controls the watchdog timer of a device. The timer activates when you start the task. Use the digital physical channel expiration states input to set expiration states ...

Creates channel(s) to measure voltage. Use this instance for custom sensors that require excitation. You can use the excitation to scale the measurement. LabVIEW NXG does not support FPGA devices Not supported ...

Deletes a Network DAQ device previously added to the host. If the device is reserved, it is unreserved before it is removed. LabVIEW NXG does not support FPGA devices Not supported in VIs that run in a ...

Deletes the specified global channel from MAX. This node does not remove the global channel from tasks that use it. LabVIEW NXG does not support FPGA devices Not supported in VIs that run in a web application ...

Deletes the specified custom scale from MAX. This node does not remove the custom scale from virtual channels that use it. LabVIEW NXG does not support FPGA devices Not supported in VIs that run in a web ...

Creates channel(s) that use a Wheatstone bridge to measure force or load. Use this instance with sensors whose specifications provide a table of electrical values and the corresponding physical values. ...

Gets the resistor level for lines when they are in tristate logic. LabVIEW NXG does not support FPGA devices Not supported in VIs that run in a web application DAQmx Get Power Up States (Digital Pull Up ...

Creates channel(s) that use a frequency-to-voltage converter to measure frequency. LabVIEW NXG does not support FPGA devices Not supported in VIs that run in a web application DAQmx Create Channel (AI-Frequency-Voltage).vi ...

Gets the available connections on an SC Express accessory for the specified physical channel(s). Connections specify how channels on the SC Express accessory should be configured. The resulting configuration ...

Starts an external calibration session on a device. LabVIEW NXG does not support FPGA devices Not supported in VIs that run in a web application DAQmx Initialize External Calibration.vi :/lvdaqmx.chm::/mxinitextcal.html ...

Queries the status of the task and indicates if it completed execution. Use this node to ensure that the specified operation is complete before you stop the task. LabVIEW NXG does not support FPGA devices ...

Performs shunt calibration for the specified channels using a bridge sensor. LabVIEW NXG does not support FPGA devices Not supported in VIs that run in a web application DAQmx Perform Shunt Calibration ...

Showing 161-180 of 2088 results
9 of 105 pages