Filtered Results

Updates power up states for digital physical channels. LabVIEW NXG does not support FPGA devices Not supported in VIs that run in a web application DAQmx Set Power Up States (Digital).vi :/lvdaqmx.chm::/DAQmx ...

Configures when the DAQ device transfers data to a peripheral device, using an imported sample clock to control burst handshake timing. LabVIEW NXG does not support FPGA devices Not supported in VIs that ...

Sets the source of the Sample Clock, the rate of the Sample Clock, and the number of samples to acquire or generate. The device acquires or generates samples on each Sample Clock edge, but it does not ...

Sets the source of the Sample Clock, the rate of the Sample Clock, and the number of samples to acquire or generate. LabVIEW NXG does not support FPGA devices Not supported in VIs that run in a web application ...

Indicates if the sample clock timing type is supported for the digital input physical channel. Not supported Not supported in VIs that run in a web application 29A5 attr29A5.html

Indicates the set of discrete lowpass cutoff frequencies supported by this device. If the device supports ranges of lowpass cutoff frequencies, use AI.DigFltr.Lowpass.CutoffFreq.RangeVals to determine ...

Indicates sample modes supported by devices that support sample clocked analog input. Not supported Not supported in VIs that run in a web application Finite Samples 10178 Acquire or generate a finite ...

Indicates in hertz the maximum counter timebase frequency. Not supported Not supported in VIs that run in a web application 29A0 attr29A0.html

Indicates the measurement types supported by the physical channels of the device. Refer to CI.MeasTypes for information on specific channels. Not supported Not supported in VIs that run in a web application ...

Specifies the maximum size of a USB transfer request in bytes. Modify this value to affect performance under different combinations of operating system and device. Not supported Not supported in VIs that ...

Indicates the number of samples available to read per channel. This value is the same for all channels in the task. Not supported Not supported in VIs that run in a web application 1223 attr1223.html

Specifies the logic level behavior on the input line. Not supported Not supported in VIs that run in a web application Logic Level Pull-up 16064 High logic. None 10230 Supply no excitation to the channel. ...

Specifies in seconds the minimum pulse width the filter recognizes. Not supported Not supported in VIs that run in a web application 21E8 attr21E8.html

Specifies the divisor for an external counter timebase. You can divide the counter timebase in order to generate slower signals without causing the count register to roll over. Not supported Not supported ...

Specifies the number of ticks to wait before generating the first pulse. Not supported Not supported in VIs that run in a web application 298 attr298.html

Specifies the amount of time to wait after receiving a Sample Clock edge before beginning to acquire the sample. This value is in the units you specify with DelayFromSampClk.DelayUnits. Not supported Not ...

Digital filtering rejects state transitions that do not stay at a state for a specified amount of time. For example, for an edge counting measurement with digital filtering, the device does not count an ...

Device ID Device Name 0x0160NI PCI-DIO-96 0x075CNI DAQCard-DIO-24 0x075FNI DAQCard-6715 0x1150NI PCI-DIO-32HS 0x1290NI PCI-6704 0x12B0NI PCI-6534 0x1310NI PCI-6602 0x1320NI PXI-6533 0x1360NI PXI-6602 0x13C0NI ...

On an NI 4300 or NI 433x device, you can either acquire a signal present on the I/O connector, or you can acquire an onboard signal, via an internal multiplexer. The channels available on this multiplexer ...

Specifies how DAQmx Write waits for space to become available in the buffer. Not supported Not supported in VIs that run in a web application Poll 12524 Repeatedly check for available buffer space as fast ...

Showing 101-120 of 2163 results
6 of 109 pages