Filtered Results

Creates channel(s) that use an accelerometer to measure acceleration. You must configure the physical channel(s) with TEDS information to use this VI. LabVIEW NXG does not support FPGA devices Not supported ...

Creates channel(s) that measure a Wheatstone bridge. You must configure the physical channel(s) with TEDS information to use this VI. Use this instance with bridge-based sensors that measure phenomena ...

Changes the external calibration password of the device. LabVIEW NXG does not support FPGA devices Not supported in VIs that run in a web application DAQmx Change External Calibration Password.vi :/lvdaqmx.chm::/mxchangeextcalpassword.html ...

Creates channel(s) that use a Wheatstone bridge to measure force or load. You must configure the physical channel(s) with TEDS information to use this VI. NI-DAQmx scales electrical values to physical ...

Creates a custom scale that scales values proportionally from a range of pre-scaled values to a range of scaled values. LabVIEW NXG does not support FPGA devices Not supported in VIs that run in a web ...

Creates a custom scale that uses an nth order polynomial equation. LabVIEW NXG does not support FPGA devices Not supported in VIs that run in a web application DAQmx Create Scale (Polynomial).vi :/lvdaqmx.chm::/DAQmx ...

Creates a custom scale that maps an array of pre-scaled values to an array of corresponding scaled values. NI-DAQmx applies linear interpolation to values that fall between the values in the table. LabVIEW ...

Creates and configures a custom scale. Apply custom scales to input and output channels to provide additional scaling.

Creates a task and adds virtual channels to that task if you specify them in the global virtual channels input. If you specify a task to copy, this node duplicates the configuration of the specified task ...

Creates a virtual channel, or set of virtual channels, and adds them to a task. You must configure the physical channel(s) with TEDS information to use this node. If you use this node within a loop without ...

Creates a timing source that sends ticks to a Timed Loop at a constant frequency. NI-DAQmx uses the counter you specify to generate the signal for the timing source. LabVIEW NXG does not support FPGA devices ...

Creates a timing source for a Timed Loop. The timing source is based on signals a device generates. Timing sources send ticks to a timed loop. Those ticks determine when the Timed Loop executes. By default, ...

Creates a timing source that uses the signal you specify to determine when to send ticks to a Timed Loop. You must create a task that can generate the signal and wire that task to the task/channels in ...

Creates and configures a task that controls the watchdog timer of a device. The timer activates when you start the task. Use the digital physical channel expiration states input to set expiration states ...

Creates channel(s) to measure voltage. Use this instance for custom sensors that require excitation. You can use the excitation to scale the measurement. LabVIEW NXG does not support FPGA devices Not supported ...

Deletes a Network DAQ device previously added to the host. If the device is reserved, it is unreserved before it is removed. LabVIEW NXG does not support FPGA devices Not supported in VIs that run in a ...

Reads one or more pairs of pulse high and low tick counts from a counter input task. LabVIEW NXG does not support FPGA devices Not supported in VIs that run in a web application DAQmx Read (Counter 1D ...

Returns the reference values to be used by a reference device to create a reference signal. LabVIEW NXG does not support FPGA devices Not supported in VIs that run in a web application DAQmx Get 9775 Calibration ...

Deletes the specified task from MAX. This node does not clear the copy of the task stored in memory. Use the DAQmx Clear Task node to clear that copy of the task. LabVIEW NXG does not support FPGA devices ...

Showing 101-120 of 2006 results
6 of 101 pages