Filtered Results

Specifies whether to synchronize recognition of transitions in the signal to the internal timebase of the device. Not supported Not supported in VIs that run in a web application 2EEA attr2EEA.html

Specifies a hysteresis level in the units of the measurement. If Ref.AnlgEdge.Slope is Rising, the trigger does not deassert until the source signal passes below Ref.AnlgEdge.Lvl minus the hysteresis. ...

Specifies in the units of the measurement the threshold at which the Reference Trigger occurs. Use Ref.AnlgEdge.Slope to specify on which slope to trigger at this threshold. Not supported Not supported ...

Specifies on which slope of the source signal the Reference Trigger occurs. Not supported Not supported in VIs that run in a web application Rising 10280 Trigger on the rising slope of the signal. Falling ...

Indicates if the device(s) detected an open current loop for any virtual channel in the task. Reading this property clears the open current loop status for all channels in the task. You must read this ...

Specifies the lower limit of the window. Specify this value in the units of the measurement. Not supported Not supported in VIs that run in a web application 1428 attr1428.html

Specifies the coupling for the source signal of the trigger if the source is a terminal rather than a virtual channel. Not supported Not supported in VIs that run in a web application AC 10045 Alternating ...

Specifies whether to apply a digital filter to the digital output of the analog triggering circuitry (the Analog Comparison Event). When enabled, the analog signal must stay within the trigger window for ...

Indicates a list of names of any overloaded virtual channels in the task. You must read OverloadedChansExist before you read this property. Otherwise, you will receive an error. Not supported Not supported ...

Indicates if the device(s) detected an overload in any virtual channel in the task. Reading this property clears the overload status for all channels in the task. You must read this property before you ...

Indicates if the device(s) detected an overload in any virtual channel in the task. Reading this property clears the overload status for all channels in the task. You must read this property before you ...

Specifies the type of trigger to use to expire a watchdog task. Not supported Not supported in VIs that run in a web application Digital Edge 10150 Trigger on a rising or falling edge of a digital signal. ...

Indicates a list of names of any virtual channels in the task for which an External Overvoltage condition has been detected. You must read External OvervoltageChansExist before you read this property. ...

Indicates if the device(s) detected an External Overvoltage condition for any channel in the task. Reading this property clears the External Overvoltage status for all channels in the task. You must read ...

Specifies the timescale to be used for the value of FirstSampClk.When. Not supported Not supported in VIs that run in a web application Host Time 16126 Use the host device. I/O Device Time 16127 Use the ...

Specifies the time of the first sample clock pulse. Not supported Not supported in VIs that run in a web application 1347 attr1347.html

Specifies whether to apply a digital filter to the digital output of the analog triggering circuitry (the Analog Comparison Event). When enabled, the analog signal must stay above or below the trigger ...

Specifies in seconds the minimum pulse width the filter recognizes. Not supported Not supported in VIs that run in a web application 2EF1 attr2EF1.html

Specifies in hertz the rate of the digital filter timebase. NI-DAQmx uses this value to compute settings for the filter. Not supported Not supported in VIs that run in a web application 2EF3 attr2EF3.html ...

Specifies in seconds the amount of time until the watchdog timer expires. A value of -1 means the internal timer never expires. Set this input to -1 if you use an Expiration Trigger to expire the watchdog ...

Indicates the total number of samples acquired by each channel. NI-DAQmx returns a single value because this value is the same for all channels. For retriggered acquisitions, this value is the cumulative ...

Specifies a list and/or range of analog sources that are going to be used for Analog triggering. Each source corresponds to an element in each of the Analog Multi Edge property arrays, if they are not ...

Specifies the lower limit of the window. Specify this value in the units of the measurement or generation. Not supported Not supported in VIs that run in a web application 1402 attr1402.html

Specifies the coupling for the source signal of the trigger if the source is a terminal rather than a virtual channel. Not supported Not supported in VIs that run in a web application AC 10045 Alternating ...

Specifies whether to apply a digital filter to the digital output of the analog triggering circuitry (the Analog Comparison Event). When enabled, the analog signal must stay within the trigger window for ...

Specifies in seconds the minimum pulse width the filter recognizes. Not supported Not supported in VIs that run in a web application 2F00 attr2F00.html

Specifies the terminal to which to route the Watchdog Timer Expired Event. Not supported Not supported in VIs that run in a web application 21AA attr21AA.html

Specifies the terminal of the signal to use as the timebase of the digital filter. Not supported Not supported in VIs that run in a web application 2F01 attr2F01.html

Specifies whether to synchronize recognition of transitions in the signal to the internal timebase of the device. Not supported Not supported in VIs that run in a web application 2F03 attr2F03.html

Specifies the name of a virtual channel or terminal where there is an analog signal to use as the source of the Start Trigger. Not supported Not supported in VIs that run in a web application 1400 attr1400.html ...

Showing 61-90 of 2037 results
3 of 68 pages