Filtered Results

In the MAX configuration tree, expand Devices and Interfaces . Expand the Chassis tree to see the list of installed hardware, and press to refresh the list. If the module is still not listed, power ...

Restart the system. Launch MAX, and perform the self-test again. Power off the chassis. Reinstall the failed module in a different slot. Power on the chassis. Perform the self-test again. Parent topic: ...

... Volatility PCI/PXI-5152/5153/5154 March 2017 This document is ... 196638x-03L NI PXI-5152, 256MB/CH 196638x 02L NI PXI-5152, 64MB/CH ... 01L NI PXI-5152, 8MB/CH 190502x-03L NI PCI-5153, 256MB/CH ...

... NI-SCOPE PXI-5152 Front Panel Tags: API Overview NI-SCOPE >PXI-5152 Front Panel The following figure shows ... of the PXI-5152. Descriptions of the LEDs and connectors ...

... NI-SCOPE NI PXI-5152 Block Diagram Tags: API Overview NI-SCOPE >NI PXI-5152 Block Diagram The following figure shows ... the NI PXI-5152. The dual ADC architecture enables the ...

... NI-SCOPE NI PXI-5152/5153/5154 Clocking Tags: API Overview NI-SCOPE >NI PXI-5152/5153/5154 Clocking The clock circuitry ... the NI PXI-5152/5153/5154. Sample Clock The NI PXI-5152/5153/5154 ...

I need to know the exact time it is taking to my scope to acquire data in my application. The acquisition time of my Scope/Digitizer is not what I expect, and it is taking too much to acquire the data. ...

I am using NI-SCOPEmulti device session in my LabVIEW codeto configure a channel of each of the two NI PXIe-5162(4 Channel) in myPXI system. Iwould like to measure the Time Delay & Phase Delay between ...

How to use channel0 to trigger channel1 to acquire signal with PXI Oscilloscope like PXIe-5122. There is such feature in Soft Front Panel. How can I make it with LabVIEW program?

Typically, a high-speed digitizer uses an internal sample clock to determine the rate to acquire data. Are there occasions when it would be better to use an external clock source?

What is an eye diagram? What is it used for? What information is reflected in the waveform? What is the corresponding solution for NI?

How to use the "Start trigger" function with NI-SCOPE just like in DAQmx? I tried to use "niScope Configure Trigger (poly)" but it did not work as I expected. I want to do a continuous measurement with ...

My NI-Scope code is running in a simple loop where there are no configuration VIs between my niScope Initiate VI and my niScope Read VI. But when executing the code, I get: Error -1074118647 occurred ...

I am attempting to put together a system to do Time Domain Reflectometry (TDR), which observes the reflected waveforms in transmission lines. This could involve data acquisition, digital signal processing ...

Trigger timestamping and Waveform timestamping can be needed when you perform a measurement or synchronize a measurement. In this article, we will look at a NI-SCOPE-based implementation of Timestamp.

Averaging is a common operation in data acquisition, and you can perform this using the NI-Scope driver functions in LabVIEW.

... NI-SCOPE NI PXI-5152/5153/5154 Trigger Sources Tags: API ... NI-SCOPE >NI PXI-5152/5153/5154 Trigger Sources The following ... the NI PXI-5152/5153/5154. Was this information helpful? ...

Showing 31-60 of 159 results
2 of 6 pages