Filtered Results

A DAQmx property node preselected to contain Device class properties. You can select other classes from the node on the diagram.

A DAQmx property node preselected to contain Timing class properties. You can select other classes from the node on the diagram.

Use the DAQmx Physical Channel properties to query information about physical channels. Use the DAQmx Channel properties to configure virtual channels.

A terminal is a named location where a signal is either generated (output or produced) or acquired (input or consumed). A terminal that can output only one signal is often named after that signal. A terminal ...

A DAQmx property node preselected to contain System class properties. You can select other classes from the node on the diagram.

Removes signal routes you created by using the DAQmx Connect Terminals node. DAQmx Disconnect Terminals cannot remove task-based routes, such as those you create through timing and triggering configuration. ...

Use the DAQmx DSA Calibration nodes to perform external calibrations of the analog input section, analog output section, and timebase of DSA devices.

Use the DAQmx Events nodes and functions for event-driven programming using NI-DAQmx.

Routes a control signal to the terminal you specify. The output terminal can reside on the device that generates the control signal or on a different device. You can use this node to share clocks and triggers ...

Converts an array of physical or virtual channel names to a comma-delimited list of names. You can use this node to convert an array of channel names to a single string prior to using DAQmx Create Virtual ...

Returns the reference voltage values to be used by a reference device to create a reference signal. LabVIEW NXG does not support FPGA devices Not supported in VIs that run in a web application DAQmx Get ...

Returns the reference voltage values to be used by a reference device to create a reference signal. LabVIEW NXG does not support FPGA devices Not supported in VIs that run in a web application DAQmx Get ...

Returns the reference voltage values to be used by a reference device to create a reference signal. LabVIEW NXG does not support FPGA devices Not supported in VIs that run in a web application DAQmx Get ...

Returns the reference voltage values to be used by a reference device to create a reference signal. LabVIEW NXG does not support FPGA devices Not supported in VIs that run in a web application DAQmx Get ...

Gets the power up states for analog physical channels. LabVIEW NXG does not support FPGA devices Not supported in VIs that run in a web application DAQmx Get Power Up States (Analog With Output Type).vi ...

Gets the power up states for analog physical channels. LabVIEW NXG does not support FPGA devices Not supported in VIs that run in a web application DAQmx Get Power Up States (Analog).vi :/lvdaqmx.chm::/DAQmx ...

Gets the power up states for digital physical lines. LabVIEW NXG does not support FPGA devices Not supported in VIs that run in a web application DAQmx Get Power Up States (Digital).vi :/lvdaqmx.chm::/DAQmx ...

Gets the digital logic family for a device. LabVIEW NXG does not support FPGA devices Not supported in VIs that run in a web application DAQmx Get Power Up States (Digital Logic Family).vi :/lvdaqmx.chm::/DAQmx ...

Gets the resistor level for lines when they are in tristate logic. LabVIEW NXG does not support FPGA devices Not supported in VIs that run in a web application DAQmx Get Power Up States (Digital Pull Up ...

Returns the power up states that physical channels on a device are set to when the device powers up or when you reset the device. This node returns data for only one line.

Gets the available connections on an SC Express accessory for the specified physical channel(s). Connections specify how channels on the SC Express accessory should be configured. The resulting configuration ...

Creates channel(s) to measure strain. LabVIEW NXG does not support FPGA devices Not supported in VIs that run in a web application DAQmx Create Channel (AI-Strain-Strain Gage).vi :/lvdaqmx.chm::/DAQmx ...

Returns the reference current values to be used by a reference device to create a reference signal. LabVIEW NXG does not support FPGA devices Not supported in VIs that run in a web application DAQmx Get ...

Returns the reference voltage values to be used by a reference device to create a reference signal. LabVIEW NXG does not support FPGA devices Not supported in VIs that run in a web application DAQmx Get ...

Performs shunt calibration for the specified channels using a strain gage sensor. LabVIEW NXG does not support FPGA devices Not supported in VIs that run in a web application DAQmx Perform Shunt Calibration ...

Creates channel(s) to measure voltage RMS, the average (mean) power of the acquired voltage. LabVIEW NXG does not support FPGA devices Not supported in VIs that run in a web application DAQmx Create Channel ...

Showing 1-30 of 2037 results
1 of 68 pages