Filtered Results

You must be an Administrator to install NI software on your computer. Install an ADE, such as LabVIEW or LabWindows™/CVI™. Install the driver software using NI Package Manager or by inserting your driver ...

Restart the system. Launch MAX, and perform the self-test again. Power off the chassis. Reinstall the failed module in a different slot. Power on the chassis. Perform the self-test again.

It is important to perform a self-calibration after first connecting your system because of cabling and mismatch effects and some degree of residual error, which result from module interconnections. You ...

Table 14. Locations of NI-RFmx Software ADE Location LabVIEW Available on the LabVIEW Functions palette at Measurement I/O > NI-RFmx . LabWindows/CVI NI-RFmx functions are available from the LabWindows/CVI ...

NI provides several software options for the PXIe-5668—NI-RFmx, the NI-RFSA instrument driver software, and the NI-RFSA Soft Front Panel (SFP).

These specifications apply to the PXIe-5668 (14 GHz) Vector Signal Analyzer and the PXIe-5668 (26.5 GHz) Vector Signal Analyzer with 320/765 MHz bandwidth, 200 MHz bandwidth, or 80 MHz bandwidth.

Note Before you begin, install and configure your chassis and controller. This document explains how to install, configure, and test the PXIe-5668 . The PXIe-5668 is a 26.5 GHz or 14 GHz modular vector ...

Verify that the discrepancy between the PXIe-5668 and the source is within the error limits of the devices. Verify the absolute amplitude accuracy of the PXIe-5668 using the appropriate value. Verify the ...

Failure to initialize may indicate a problem with module interconnections or with MAX. If the niRFSA Initialize VI or the niRFSA_init function returns an error and the PXIe-5668 fails to initialize, complete ...

Refer to the following figure for information about other product tasks and associated resources for those tasks.

This product was tested and complies with the regulatory requirements and limits for electromagnetic compatibility (EMC) stated in the product specifications. These requirements and limits provide reasonable ...

There are several required items not included in your device kit that you need to operate the PXIe-5668. Your application may require additional items not included in your kit to install or operate your ...

The LEDs may not light until the device has been configured in MAX. Before proceeding, verify that the PXIe-5668 appears in MAX. If the ACCESS LED fails to light after you power on the chassis, a problem ...

In the MAX configuration tree, expand Devices and Interfaces . Expand the Chassis tree to see the list of installed hardware, and press to refresh the list. If the module is still not listed, power ...

Notice To prevent damage to the PXIe-5668 caused by ESD or contamination, handle the module using the edges or the metal bracket. Ensure the AC power source is connected to the chassis before installing ...

NI recommends you run the self-calibration from the NI-RFSA SFP. You can also run a self-calibration programmatically using the NI-RFSA API.

Notice To prevent electrostatic discharge (ESD) from damaging the device, ground yourself using a grounding strap or by holding a grounded object, such as your computer chassis. Touch the antistatic package ...

If the IF digitizer module fails to phase-lock to the PXIe-5606 4 GHz LO2 OUT through the front panel, determine whether one of the following errors has occurred: Verify that the cable is not faulty and ...

Use Measurement & Automation Explorer (MAX) to configure your NI hardware. MAX informs other programs about which NI hardware products are in the system and how they are configured. MAX is automatically ...

The PXIe-5606 downconverter module has no internal DC block, so high-frequency components in the PXIe-5606 can be damaged when DC signals are applied directly to the RF IN connector. The PXIe-5606 ships ...

The PXIe-5606 is a precision RF instrument that is sensitive to ESD and transients. Ensure you are making proper direct connections to the PXIe-5606 to avoid damaging the device.

Complete the following steps to interconnect the PXIe-5668 front panel connectors, as shown in the following figure. Notice The signal pins of this product's input/output ports can be damaged if subjected ...

If you're using NI-RFmx or NI-RFSA with LabVIEW or LabWindows/CVI , use the NI Example Finder to locate programming examples. Launch LabVIEW or LabWindows/CVI . Select Help > Find Examples to open the ...

If you're using NI-RFmx or NI-RFSA with Microsoft Visual C/C++, locate examples in the following directories.

Figure 6. Installing the DC Block on the PXIe-5606 RF IN Connector 1 1 2 3 4 Screws DC block support DC block PXIe-5606 RF IN Connector Attach the DC block to the RF IN connector on the PXIe-5606 downconverter ...

Figure 5. Removing the DC Block from the PXIe-5606 RF IN Connector 2 1 3 2 DC block Screws DC block support Remove the two screws on the DC block support with a Torx screwdriver with a T8 bit. Loosen

Verify the front panel interconnections for your RF vector signal analyzer . Verify the MAX device association for your PXIe-5668 . If you have verified the interconnections and associations of your device ...

Showing 1-30 of 76 results
1 of 3 pages