Filtered Results

In your Test Specification document, click the Add Event button. The Configure Event dialog opens. Create the If condition that will trigger the event. Channel value change Click the Select channel button ...

You can use test properties as placeholders when you configure your log file name and location. Refer to the Using Test Metadata as Placeholders for Log File Names and Locations topic for more information. ...

NI recommends the read rate of 1 Hz for data using SystemLink tags. For channels that require a faster read data rate, consider using the FlexLogger Plugin Development Kit to create a custom LabVIEW plugin ...

Add and configure signals to use in your Channel specification. Use any of the following options that apply to the devices in your system: Configure sensors in your Channel Specification Configure digital ...

Low-Speed CAN requires termination at the Low-Speed CAN transceiver instead of on the cable. The termination requires two resistors: RTH for CAN_H and RTL for CAN_L. This configuration allows the NXP fault-tolerant ...

If there's a way we could shorten/condense this example, I can see a case for leaving it in this topic. But it's so much longer than the steps themselves the way it is now, which makes the topic less focused. ...

Complete the following steps to apply scaling to your configured sensor. Click the Configure gear on the channel of the device you wish to scale. The channel configuration dialog opens. In the Scaling ...

Extend the functionality of FlexLogger by adding a custom plugin to your project. What to UseThe FlexLogger Plugin Development Kit guides you through planning, creating, and testing your custom plugins ...

Select one or more channels you wish to add an alarm to. Hover over a channel row to see the Configure gear . Click the gear for the channel you wish to add an alarm to. Select the Alarms tab in the Channel ...

In your Test Specification document, click the Add Event button. The Configure Event dialog opens. Create the If condition that will trigger the event. Channel value change Click the Select channel button ...

You can use test properties as placeholders when you configure your log file name and location. Refer to the Using Test Metadata as Placeholders for Log File Names and Locations topic for more information. ...

Before adding CAN and LIN signals to your Channel Specification, you may need to create or manage the databases that provide the signal definitions and scaling information for your application. Refer to ...

CAN interfaces are software representations of physical ports. Complete the following steps to adjust the port settings. Enable Termination, if necessary. Improperly configured Termination schemes might ...

LIN interfaces are software representations of physical ports. Complete the following steps to adjust the port settings. Enable Termination, if necessary. Improperly configured Termination schemes might ...

Click Add Signals on the CAN port you want to configure. Select the Database that contains the signals you want to update. Select the Cluster that contains the signals you want to apply J1939 to. Select ...

On the Logging Specification document, select Export automatically to CSV file format when logging completes. Specify the CSV file data rate, if necessary. All logged data channels are mapped to a common ...

In your Channel Specification document, select all configured channels you wish to calibrate. In your Channel Specification document toolbar, click the Calibrate channels button . Select one of the following ...

Although it is possible (and supported) in principle to run a network without a database, using a database is highly recommended to have a consistent set of network parameters for all nodes in the network. ...

Specify the base path for the location where your data file will be saved and file name. You can add test properties to a project and use them as placeholders when you specify your data log file name and ...

Select one or more channels you wish to configure. Hover over a channel row and click the Configure gear . The configure gear appears when selecting multiple channels of the same data type (analog, digital, ...

Select one of the following options depending on your automotive network: Use CAN databases—Manage and configure CAN databases to determine which signals to use in your Channel Specification. Use LIN databases—Manage ...

Add a calculated Boolean channel to produce a high or low Boolean digital signal based on an analog or digital channel. On the Channel Specification toolbar, select Add channel Calculation Boolean formula ...

A calculated channel produces a new value based on calculations performed on other channels in the system. You can choose from the following calculation types: Configuring RMS and Mean Channels Configuring ...

Add counters to a project by configuring signals in the Channel Specification. Use these steps to configure counters for counter modules, such as the NI-9361, and onboard counters by enabling the line ...

You can configure the data rate at which your DAQ device acquires data by customizing the data ranges and setting the values for analog (slow, medium, and fast) and digital data rate levels. For devices ...

Refer to the following information to configure your device channels. Configuring I/O Channels Configuring an Automotive Bus Configuring Calculated Channels After you configure your channels, you can start ...

Select one or more channels you wish to configure. Hover over a channel row and click the Configure gear . The configure gear appears when selecting multiple channels of the same data type (analog, digital, ...

Add a channel produced by applying either a lowpass or a highpass Butterworth filter to an existing hardware channel. The lowpass or highpass filter channel displays filtered data that excludes any noise ...

Add a calculated channel to analyze or scale data from existing hardware channels. A calculated channel produces a new value based on calculations performed on other channels in the system. On the Channel ...

Add and configure signals to use in your Channel specification. Use any of the following options that apply to the devices in your system: Configure sensors in your Channel Specification Configure digital ...

Showing 1-30 of 85 results
1 of 3 pages