Filtered Results

... PXIe-5114,NI PXIe-5122,NI PXIe-5160,NI PXIe-5160 4CH,NI PXIe-5162,NI ...

SPECIFICATIONS PXIe-5122 PXIe, 100 MHz, 100 MS/s, 14-Bit PXI ... ni.com | PXIe-5122 Specifications Impedance and Coupling ... only. PXIe-5122 Specifications | © National Instruments ...

... Drawings PXIe-5122 Dimensional Drawings PXIe-5122 Dimensional ... for the PXIe-5122. 2D Dimensional Drawings PDF DXF 3D ...

... INFORMATION PXIe-5122 PXIe, 100 MHz, 100 MS/s, 14-Bit PXI ... ni.com | PXIe-5122 Safety, Environmental, and Regulatory ... about the PXIe-5122, including specifications, pinouts, ...

The NI PXI Oscilloscope acquires and analyzes time- and frequency‐domain analog signals as part of a PXI system.

... PCI/PXI/PXIe-5122 March 2017 This document is subject ... 195945x-01L NI PXIe-5122, 8MB/CH 195945x-02L NI PXIe-5122, 64MB/CH 195945x-03L NI PXIe-5122, 256MB/CH Volatile Memory Target Data ...

NI provides the following calibration services to help you keep your NI oscilloscope/digitizer performing at its best. Traceable Calibration Service With traceable calibration, you can track how your ...

... the PXI/PXIe-5122............................................................ ... the PXI/PXIe-5122 Caution To prevent damage to the PXI/PXIe/PCI-5122 ... the PXI/PXIe-5122 to the controller. ACTIVE Indicates ...

Learn about acquiring an analog signal, including topics such as bandwidth, amplitude error, rise time, sample rate, the Nyquist Sampling Theorem, aliasing, and resolution.

What is an eye diagram? What is it used for? What information is reflected in the waveform? What is the corresponding solution for NI?

How to use the "Start trigger" function with NI-SCOPE just like in DAQmx? I tried to use "niScope Configure Trigger (poly)" but it did not work as I expected. I want to do a continuous measurement with ...

My NI-Scope code is running in a simple loop where there are no configuration VIs between my niScope Initiate VI and my niScope Read VI. But when executing the code, I get: Error -1074118647 occurred ...

I have a National Instruments PXI Oscilloscope card and my device fails the self-test in NI Measurement & Automation Explorer (MAX) with one of the error codes below: -239000 -239001 -239020 -239022 -200550 ...

I am using NI-SCOPEmulti device session in my LabVIEW codeto configure a channel of each of the two NI PXIe-5162(4 Channel) in myPXI system. Iwould like to measure the Time Delay & Phase Delay between ...

I am attempting to put together a system to do Time Domain Reflectometry (TDR), which observes the reflected waveforms in transmission lines. This could involve data acquisition, digital signal processing ...

I have an NI-SCOPE device and would like to adjust the Channel 0 vertical range independently of the Channel 1 vertical range. I have tried using the niScope Configure Vertical VI but it changes the settings ...

I need to know the exact time it is taking to my scope to acquire data in my application. The acquisition time of my Scope/Digitizer is not what I expect, and it is taking too much to acquire the data. ...

Typically, a high-speed digitizer uses an internal sample clock to determine the rate to acquire data. Are there occasions when it would be better to use an external clock source?

PXI Oscilloscopes are flexible, software‐defined instruments that are versatile enough for both time‐ and frequency‐domain measurements.

... Figure 1. PXIe-5122 Frequency Response, Measured Frequency ... Figure 2. PXIe-5122 Dynamic Performance, 50 Ω, 1 V Range, ... Figure 3. PXIe-5122 Spectral Noise Density, 0.2 V Input ...

... Topic PXIe-5122 triggering problem PXIe-5122 triggering ... Reply Re: PXIe-5122 triggering problem Tunde_S NI Employee ... using the PXIe-5122? Tunde S. Applications Engineer National ...

Showing 1-30 of 181 results
1 of 7 pages