NI CompactRIO 19.6 and Drivers Bug Fixes

Overview

The following items are notable issues fixed between the release of NI CompactRIO 19.5 and Drivers and NI CompactRIO 19.6 and Drivers, including additional patches and service packs. If you have a issue ID, you can search this list to validate that the issue has been fixed. This is not an exhaustive list of issues fixed in the current version of NI CompactRIO 19.6 and Drivers.

Contents

Bugs Fixed

 

Additional Patch Information

Installing some patches may require certain additional steps or considerations. Please refer to the following table for more information about patches for this release.

These patches currently do not have any special instructions.

Bug IDLegacy IDDescriptionDetails
949318895113

Firmware Update when Bitfile Downloaded to Memory Can Cause Unrecoverable Error or Failed Software Installation

An unrecoverable error due to Safe Mode corruption can occur when updating firmware on certain RIO targets if a large bitfile is currently in flash memory. In some cases, the firmware update is successful and there is no unrecoverable error, but software installation on the target will fail. This issue only occurs in RIO targets with a Xilinx Zynq FPGA chip that have a large bitfile downloaded to flash memory.

Note: This is not the only cause of an unrecoverable error on RIO targets with Xilinx Zynq FPGA chips.


Workaround: If the RIO status light shows an unrecoverable error (continuous flashing), contact National Instruments Technical Support and reference this Known Issue to receive the recovery instructions.

If the firmware update is successful but the RIO is unable to install software, recover in one of the following ways:

  • Revert to the older firmware version
  • Enable SSHD and manually remove the lvbitx file that was downloaded to memory in the /boot partition

 

To prevent this issue in the future:

Reported Version: 

NI CompactRIO 16.0 |
NI CompactRIO 17.0 |
NI CompactRIO 17.6 |
NI CompactRIO 18.0 |
NI CompactRIO 18.1 |
NI CompactRIO 18.5 |
NI CompactRIO 19.0 |
NI CompactRIO 19.1 |
NI CompactRIO 19.5

Resolved Version: 
NI CompactRIO 19.6

952841213378

NI 9202 FPGA IO Nodes Acquiring Faster Than Maximum Data Rate

Adding an NI 9202 to a CompactRIO project without configuring the module properties or programmatically setting the data rate will cause the NI 9202 FPGA I/O Nodes to acquire data at a rate faster than the maximum data rate. This can lead to invalid data or the error 65539, but it is not the only cause of error 65539.

Workaround: For more information on the below workarounds, see the Additional Information section in  KnowledgeBase article "Error 65539 Using FPGA I/O Nodes with NI 9202."

Reported Version:

NI CompactRIO 17.0 |
NI CompactRIO 17.6 |
NI CompactRIO 18.0 |
NI CompactRIO 18.1 |
NI CompactRIO 18.5 |
NI CompactRIO 19.0 |
NI CompactRIO 19.1 |
NI CompactRIO 19.5

Resolved Version:
NI CompactRIO 19.6

952865196448

Export to CSV in the LabVIEW CLIP Generator Ignores sbRIO Bank Voltages

Using the Export to CSV option in the LabVIEW CLIP Generator exports the CLIP parameters for I/O pin bank voltages incorrectly. This results in an incorrect CSV file and only the default pin configuration being set when using the file for import.

Workaround:

  • Manually change the bank voltages in the CSV file after exporting
  • Change the incorrect bank voltage values in the LabVIEW CLIP Generator after importing the incorrect CSV file
  • Update to NI CompactRIO 19.6 or later and then export the configuration

Reported Version: 
NI CompactRIO 19.5

Resolved Version: 
NI CompactRIO 19.6

Glossary of Terms

 

  • Bug ID - When an issue is reported to NI, you may be given this ID or find it on ni.com.  You may also find IDs posted by NI on the discussion forums or in KnowledgeBase articles.
  • Legacy ID – An older issue ID that refers to the same issue.  You may instead find this issue ID in older known issues documents.
  • Description - A few sentences which describe the problem. The brief description given does not necessarily describe the problem in full detail.
  • Workaround - Possible ways to work around the problem.
  • Reported Version - The earliest version in which the issue was reported.
  • Resolved Version - Version in which the issue was resolved or was no longer applicable. "N/A" indicates that the issue has not been resolved.
  • Date Added - The date the issue was added to the document (not the reported date).