Digital Instrument Custom Cables, Replacement Connectors, and Screws
Updated Jul 15, 2020
If you are trying to create a custom High-Speed Digital I/O cable, create a custom fixture or breakout, modify an existing cable, repair or replace the connector on your cable or printed circuit board (PCB), or require replacement jackscrews or jacksocket fasteners, this document provides descriptions, part numbers, and vendor information to achieve these tasks.
Note that this article replaces KnowledgeBase 56FG1R00: Where Can I Find the Dimensional Drawings of HSDIO Connectors?
Some NI manuals may still reference the previous document.
Using this Digital Instrument Cable and Accessory Guide
This guide is intended to cover connectors, backshells, screws and washers designed for use with NI HSDIO devices. It does not explicitly cover other NI product families such as DAQ, Switches, C Series, or R Series, although some models may use similar or the same parts. It also does not cover legacy or End of Life (EOL) parts or products.
Jackscrews, Jacksockets, and Washers with Part Numbers
To provide a more secure cable attachment, National Instruments now uses jackscrews to secure 68-pin cables to HSDIO devices and accessories. Each side of the cable connector contains two jackscrews that tighten into jacksockets located on all HSDIO devices and accessories. To make this conversion, use the Jacksocket Kit for Connecting Screw Latching Cables in the following table. Other replacement jackscrew, jacksocket, screwlock, thumbscrew and washer information is also provided.
Identify the part, part number, size and threading of the screws and washers used on NI HSDIO cables and accessories.
NI Orderable Part Number
Manufacturer Part Number
Latching Cable to Jackscrew Conversion Kit
(1) 4 Piece Jacksocket Kit for Connecting Screw Latching Cables
For more information on any of the listed NI orderable parts, please visit http://www.ni.com/contact-us/ to contact an NI representative. NI orderable parts listed in this guide without a product page can still be purchased by contacting NI.
For parts with a manufacturer part number, please contact the manufacturer or their vendors for further information about the product and purchasing. Manufacturer part numbers represent functionally equivalent replacements that are currently available from the specified manufacturer. This may differ from the part found on your device, module, cable or accessory as NI continuously revises and improves their products.
Some parts are custom made for NI or are common parts in industry, and do not have orderable part numbers. Please use the specifications provided to find an appropriate part.
Below is a list of the connectors referenced in this guide that are found on the most popular NI HSDIO products. This is not intended to be a complete nor comprehensive list of all NI HSDIO products. Similar cables and connectors may be used with other NI products, and are not included here. You should first check your device's manual to ensure you are referencing the right connector for your device or module.
Note: These tables do not indicate compatibility between devices, modules, cables and accessories. Although they may share the same connector type, different wire mappings are used in different configurations.
Use this table to quickly identify connector types found on many NI HSDIO devices and modules.
SCSI 0.050 D‑Type - Industry standard SCSI connector standard featuring 0.050 pin spacing that is used in the 68-position HSDIO cable and accessory connections. Click here for an example (68-pin).
Backshell - Surrounds the male or female cable connector to protect the cable connections and to provide cable strain relief. Click here for an example.
Cable Connector - Found on the end of the cable, may connect to a device, another cable, or an accessory through a mating connector. Click here for an example.
Dual Stack - Two combined connectors stacked onto each other on a PCB-mount connector. Each connector accepts its own cable. Click here for an example.
Infiniband - High density differential connector. Each differential pair in this cable is separated by a grounding pin to prevent cross-talk. - Click here for an example.
Insulation Displacement Connector (IDC) - Also known as insulation-piercing contact (IPC). A type of cable connector that allows multiple conductor connections to a connector without soldering. Click here for an example.
Jackscrew - Usually found on the cable end. Torqued down to connect to either a PCB-mount connector or cable-end jacksocket. Click here for an example.
PCB-Mount Connector - Also known as board-mount connector. Found on printed circuit boards (PCB), printed wiring boards (PWB) and other custom interface boards, normally soldered on. Typically a cable connector plugs into the PCB-mount connector to provide connection to an accessory or other device. Click here for an example.