Archived: NI PXI-4071 - 2-Wire Resistance - DMM/Switch Handshaking Scan Rates

NI does not actively maintain this document.

This content provides support for older products and technology, so you may notice outdated links or obsolete information about operating systems or other relevant products.

Overview

Benchmarking scan rate data is very useful when deciding what which devices are needed to meet system requirements. This is true of digital multimeter (DMM) and switch systems since scan rates are dependent on the speed of the digital multimeter, the switch, and the triggers between them. This document contains data for the typical scan rates that can be achieved utilizing handshaking.

Contents

Benchmarking Procedure

There are many factors which will affect the overall scanning speed of a DMM/switch system. The major factors include the type of the measurement, the range of the measurement, and resolution of the measurement. The effect of these and other factors related to the DMM can be better understood by considering the digital multimeter measurement cycle. In addition to these factors, relay operate times, DMM settling times, and switch settling times limit the overall speed of the system. The following benchmarks provide a good starting point to see typical scan rates for common use cases. 

The benchmarking application that was used to gather the following data is attached to this document. There are two top level VIs within the library. The 2-Wire Resistance with DataLog VI uses the Microsoft Report Generation Toolkit to log the acquired scan rates to an MS Excel Spreadsheet. The 2-Wire Resistance VI preforms the exact same scan rate test, but only displays the results rather than logging them to a file. Both top level VIs and all required subVIs are contained in the .llb file.

The NI-DAQmx API was used to program the switches in order to obtain these benchmarks. This program systematically cycles through each DMM resolution and range and logs all the resulting scan rates to a spreadsheet. The attached program is configured to make 2-Wire Resistance measurements, but can easily be used to benchmark scan rates for other measurement types and other devices.

Scan Rate Benchmarks

The following benchmarks show typical scan rates when using handshaking. The DMM used for testing was a NI PXI-4071 set to measure resistance in a 2-wire configuration.  Both the measurement resolution and range were varied to illustrate the resulting effect on the scan rate.

NI PXI-4071 2-Wire Resistance
Switch ModuleDMM/Switch Scan Rate (cycles/second)
RangeDigits of Resolution
≤ 4.55.56.57.5
NI PXI-2501≤ 1kΩ90561541
10kΩ19517541
100kΩ353540.8
1MΩ9930.8
≥ 10MΩ3320.4
NI PXI-2503≤ 1kΩ1009541
10kΩ707041
100kΩ252540.8
1MΩ9830.8
≥ 10MΩ3320.4
NI PXI-2527≤ 1kΩ10510041
10kΩ757041
100kΩ302540.8
1MΩ9930.8
≥ 10MΩ3320.4
NI PXI-2530≤ 1kΩ48539541
10kΩ16515041
100kΩ353540.8
1MΩ9930.8
≥ 10MΩ3320.4
NI PXI-2532≤ 1kΩ65549541
10kΩ18016541
100kΩ353540.8
1MΩ9930.8
≥ 10MΩ3320.4
NI PXI-2533≤ 1kΩ29526041
10kΩ13512541
100kΩ353540.8
1MΩ9930.8
≥ 10MΩ3320.4
NI PXI-2535≤ 1kΩ90561541
10kΩ19517541
100kΩ353540.8
1MΩ9930.8
≥ 10MΩ3320.4
NI PXI-2575≤ 1kΩ11010541
10kΩ757541
100kΩ303040.8
1MΩ9930.8
≥ 10MΩ3320.4
NI PXI-2576≤ 1kΩ11010541
10kΩ757541
100kΩ303040.8
1MΩ9930.8
≥ 10MΩ3320.4
NI PXI-2584≤ 1kΩ38032041
10kΩ15014041
100kΩ373741
1MΩ9930.8
≥ 10MΩ3320.4
NI SCXI-1127≤ 1kΩ1009541
10kΩ706541
100kΩ252540.8
1MΩ9930.8
≥ 10MΩ3320.4
NI SCXI-1128≤ 1kΩ61547041
10kΩ17516041
100kΩ353540.8
1MΩ9930.8
≥ 10MΩ3320.4
NI SCXI-1129≤ 1kΩ959041
10kΩ656541
100kΩ252540.8
1MΩ9930.8
≥ 10MΩ3320.4
NI SCXI-1130≤ 1kΩ47538541
10kΩ16015041
100kΩ353540.8
1MΩ9930.8
≥ 10MΩ3320.4
NI SCXI-1175≤ 1kΩ10510041
10kΩ757041
100kΩ252540.8
1MΩ9930.8
≥ 10MΩ3320.4

 

Optimizing System Scan Rate

There are ways to increase the speed of the system by adjusting the reading rate of a DMM. Depending on the requirements of the measurement, reducing parameters such as aperture time and turning off settings such as AutoZero will increase the overall scan rate of the system but may reduce measurement precision. These values can be experimented with to find a good balance between precision and speed for the measurement system. These benchmarks use default settings for switch and DMM configurations, however to ensure specified accuracy, extra settling time may be required.

Was this information helpful?

Yes

No