Number of channels |
8 analog input channels |
||||||
Isolation |
Galvanic isolation between channels and to chassis |
||||||
Input voltage range (AI+ to AI-) |
±10.5 V |
||||||
ADC resolution |
24 bits |
||||||
Type of ADC |
Delta-Sigma (with analog prefiltering) |
||||||
Sample mode |
Simultaneous |
||||||
TEDS support |
IEEE 1451.4 TEDS Class 2 |
||||||
|
|||||||
|
|||||||
Sampled data rates (fs) |
Refer to the following table for sample data rates supported for each timebase |
13.1072 MHz | 12.8 MHz | 12.288 MHz | 10.24 MHz |
---|---|---|---|
102.4 | 100.0 | 96.0 | 80.0 |
51.2 | 50.0 | 48.0 | 40.0 |
34.133 | 33.333 | 32.0 | 26.667 |
25.6 | 25.0 | 24.0 | 20.0* |
20.48 | 20.0 | 19.2 | 16.0 |
17.067 | 16.667 | 16.0* | 13.333 |
12.8 | 12.5 | 12.0 | 10.0* |
10.24 | 10.0 | 9.6 | 8.0 |
8.533 | 8.333 | 8.0* | 6.667 |
6.4 | 6.25 | 6.0 | 5.0* |
5.12 | 5.0 | 4.8 | 4.0 |
4.267 | 4.167 | 4.0* | 3.333 |
3.2 | 3.125 | 3.0 | 2.5* |
2.56 | 2.5 | 2.4 | 2.0 |
2.133 | 2.083 | 2.0* | 1.667 |
1.6 | 1.563 | 1.5 | 1.25* |
1.28 | 1.25 | 1.2 | 1.0 |
1.067 | 1.042 | 1.0* | 0.833 |
0.8 | 0.781 | 0.75 | 0.625 |
0.64 | 0.625 | 0.6 | 0.5 |
Note: For sample rates that can be obtained using two different timebases, the lowest noise (highest resolution) option is indicated with an asterisk (*). |
Input impedance (AI+ to AI-) |
>1 GΩ |
Input capacitance (AI+ to AI-) |
440 pF |
Temperature | Gain Error (% of Reading) | Offset Error (% of Range, mV)[2] |
---|---|---|
5 °C to 40 °C, typical | 0.013% | 0.001%, 0.105 mV |
5 °C to 40 °C, maximum | 0.037% | 0.01%, 1.05 mV |
-40 °C to 85 °C, maximum | 0.062% | 0.02%, 2.1 mV |
|
|||||||||
|
|||||||||
Gain mismatch (channel-to-channel, 40 kHz) |
0.035 dB maximum |
||||||||
Phase mismatch (channel-to-channel) |
0.03°/kHz maximum |
||||||||
Phase nonlinearity (fs = 102.4 kSamples/s) |
0.1° maximum |
||||||||
Crosstalk (1 kHz) |
-110 dB |
||||||||
CMRR to chassis/earth (fin = 60 Hz) |
130 dB |
||||||||
Spurious Free Dynamic Range (SFDR), (1 kHz, -60 dBFS) |
130 dBFS |
||||||||
Total Harmonic Distortion (THD), (1 kHz, -1 dBFS) |
-102 dB |
||||||||
MTBF |
864,132 hours at 25 °C; Bellcore Issue 6, Method 1, Case 3, Limited Part Stress Method |
Nominal output voltage range |
5 V to 24 V |
Power-on output state |
Channels off[3] |
Settling time to 1% of final value |
100 ms |
|
|||||||
Load regulation |
-2.2 mV/mA |
||||||
Resolution |
10 bits |
||||||
Voltage noise, RMS, 100 kHz BW |
3 mV |
|
13.1072 MHz | 12.8 MHz | 12.288 MHz | 10.24 MHz |
---|---|---|---|
4096 Hz | 4000 Hz | 3840 Hz | 3200 Hz |
2048 Hz | 2000 Hz | 1920 Hz | 1600 Hz |
1024 Hz | 1000 Hz | 960 Hz | 800 Hz |
512 Hz | 500 Hz | 480 Hz | 400 Hz |
256 Hz | 250 Hz | 240 Hz | 200 Hz |
128 Hz | 125 Hz | 120 Hz | 100 Hz |
Timebase | Cutoff | 4th Order | 2nd Order | ||
---|---|---|---|---|---|
DC Delay | Maximum Delay | DC Delay | Maximum Delay | ||
13.1072 MHz | 4096 | 436.19 μs | 457.52 μs | 398.81 μs | 405.2 μs |
2048 | 537.22 μs | 580.46 μs | 453.49 μs | 466.47 μs | |
1024 | 740.50 μs | 827.53 μs | 563.23 μs | 589.31 μs | |
512 | 1.14660 ms | 1.32090 ms | 783.01 μs | 834.97 μs | |
256 | 1.95850 ms | 2.30470 ms | 1.22260 ms | 1.32640 ms | |
128 | 3.58330 ms | 4.27710 ms | 2.08260 ms | 2.29250 ms | |
12.8 MHz | 4000 | 446.62 μs | 468.46 μs | 408.34 μs | 414.88 μs |
2000 | 550.08 μs | 594.35 μs | 464.33 μs | 477.62 μs | |
1000 | 758.23 μs | 847.35 μs | 576.70 μs | 603.42 μs | |
500 | 1.17410 ms | 1.35260 ms | 801.76 μs | 854.97 μs | |
250 | 2.00540 ms | 2.36000 ms | 1.25190 ms | 1.35820 ms | |
125 | 3.66920 ms | 4.37970 ms | 2.13250 ms | 2.34750 ms | |
12.288 MHz | 3840 | 465.16 μs | 487.91 μs | 425.29 μs | 432.10 μs |
1920 | 572.93 μs | 619.05 μs | 483.61 μs | 497.45 μs | |
960 | 789.76 μs | 882.59 μs | 600.67 μs | 628.49 μs | |
480 | 1.22290 ms | 1.40890 ms | 835.10 μs | 890.53 μs | |
240 | 2.08890 ms | 2.45820 ms | 1.30400 ms | 1.41470 ms | |
120 | 3.82200 ms | 4.56210 ms | 2.22130 ms | 2.44530 ms | |
10.24 MHz | 3200 | 557.87 μs | 585.16 μs | 510.02 μs | 518.19 μs |
1600 | 687.18 μs | 742.53 μs | 580.00 μs | 596.61 μs | |
800 | 947.38 μs | 1.05880 ms | 720.47 μs | 753.86 μs | |
400 | 1.46720 ms | 1.69030 ms | 1.00180 ms | 1.06830 ms | |
200 | 2.50640 ms | 2.94960 ms | 1.56440 ms | 1.69740 ms | |
100 | 4.58610 ms | 5.47420 ms | 2.66520 ms | 2.93400 ms |
|
Network protocols |
TCP/IP, UDP |
Network ports used |
HTTP:80 (configuration only), TCP:3580; UDP:5353 (configuration only), TCP:5353 (configuration only); TCP:31415; UDP:7865 (configuration only), UDP:8473 (configuration only) |
Network IP configuration |
DHCP + Link-Local, DHCP, Static, Link-Local |
Default MTU size |
1500 bytes |
Number of ports |
2 8-pin X-coded M12 ports, internally switched[8] |
Network interface |
1000 Base-TX, full-duplex; 1000 Base-TX, half-duplex; 100 Base-TX, full-duplex; 100 Base-TX, half-duplex; 10 Base-T, full-duplex; 10 Base-T, half-duplex |
Communication rates |
10/100/1000 Mbps, auto-negotiated |
Maximum cabling distance |
100 m/segment |
Maximum hops per line[9] |
15 |
|
|||||||
Maximum device power consumption[10] |
16.0 W |
||||||
Power input connector |
5-pin L-coded male M12 connector |
||||||
Power output connector |
5-pin L-coded female M12 connector |
|
|||||||
Recommended external overcurrent protection |
16 A, slow blow fuse |
Dimensions |
198.5 mm × 77.4 mm × 47.1 mm (7.8 in. × 3.0 in. × 1.9 in.) |
||||||
Weight |
1.2 kg (42 oz) |
||||||
|
|||||||
Torque for M12 connectors (power, Ethernet, input connections) |
0.6 N · m (5.31 lb · in.) |
Refer to the FD-11601 User Guide for more information about meeting these specifications.
|
|||||||
Operating and storage humidity |
Up to 100% relative humidity, condensing or noncondensing |
||||||
Ingress protection |
IP65/IP67 |
||||||
Pollution Degree |
4 |
||||||
Maximum altitude |
5,000 m |
|
|||||||
Operating shock |
100 g, 11 ms half sine, 3 shocks at 6 orientations, 18 total 40 g, 6 ms half sine, 4,000 shocks at 6 orientations, 24,000 total |
This product meets the requirements of the following environmental standards for electrical equipment.
To verify marine approval certification for a product, refer to the product label or visit ni.com/certification and search for the certificate.
Connect only voltages that are within the following limits:
|
|||||||
|
|||||||
Overvoltage protection[13] |
±30 V between any two pins on the connector |
These test and measurement circuits are not rated for measurements performed on circuits directly connected to the electrical distribution system referred to as MAINS.
MAINS is a hazardous live electrical supply system to which equipment is designed to be connected to for the purpose of powering equipment. This product is rated for measurements of voltages from specially protected secondary circuits. Such voltage measurements include signal levels, special equipment, limited-energy parts of equipment, circuits powered by regulated low-voltage sources, and electronics.
Do not connect the FD-11601 to signals or use for measurements within Measurement Categories II, III, or IV, or for measurements on MAINs circuits or on circuits derived from Overvoltage Category II, III, or IV which may have transient overvoltages above what the product can withstand. The product must not be connected to circuits that have a maximum voltage above the continuous working voltage, relative to earth or to other channels, or this could damage and defeat the insulation. The product can only withstand transients up to the transient overvoltage rating without breakdown or damage to the insulation. An analysis of the working voltages, loop impedances, temporary overvoltages, and transient overvoltages in the system must be conducted prior to making measurements.
This product is designed to meet the requirements of the following electrical equipment safety standards for measurement, control, and laboratory use:
For UL and other safety certifications, refer to the product label or the Product Certifications and Declarations section.
This product meets the requirements of the following EMC standards for electrical equipment for measurement, control, and laboratory use:
For EMC declarations and certifications, and additional information, refer to the Product Certifications and Declarations section.
This product meets the essential requirements of applicable European Directives, as follows:
Refer to the product Declaration of Conformity (DoC) for additional regulatory compliance information. To obtain product certifications and the DoC for NI products, visit ni.com/product-certifications, search by model number, and click the appropriate link.
NI is committed to designing and manufacturing products in an environmentally responsible manner. NI recognizes that eliminating certain hazardous substances from our products is beneficial to the environment and to NI customers.
For additional environmental information, refer to the Commitment to the Environment web page at ni.com/environment. This page contains the environmental regulations and directives with which NI complies, as well as other environmental information not included in this document.
At the end of the product life cycle, all NI products must be disposed of according to local laws and regulations. For more information about how to recycle NI products in your region, visit ni.com/environment/weee.