Table Of Contents

PXI-8517 Specifications

    Last Modified: November 8, 2019

    This document lists specifications for the PXI-8517 2-port Flexray interface module.


    Warranted specifications describe the performance of a model under stated operating conditions and are covered by the model warranty.

    Characteristics describe values that are relevant to the use of the model under stated operating conditions but are not covered by the model warranty.

    • Typical specifications describe the performance met by a majority of models.
    • Nominal specifications describe an attribute that is based on design, conformance testing, or supplemental testing.

    Specifications are Typical unless otherwise noted.


    Specifications are typical at 0 °C to 55 °C unless otherwise noted.

    Power Requirements

    +5 VDC (±5%)

    210 mA

    +3.3 VDC (±5%)

    940 mA


    Dimensions and Weight


    10.67 cm x 16.76 cm (4.2 in. x 6.6 in.)


    102 g (3.6 oz)

    RTSI/Front Panel Sync Connectors

    Trigger lines

    7 input/output

    Clock lines

    1 input/output

    Front panel sync connectors

    2 input/output

    I/O compatibility


    Power-on state

    Input (High-Z)


    Rising edge triggers

    Physical Characteristics


    NXP TJA1080 x 2

    Max baud rate

    10 Mbps

    Min baud rate

    1 Mbps


    Operating temperature

    0 °C to 55 °C

    Storage temperature

    -20 °C to 70 °C (Tested in accordance with IEC-60068-2-1 and IEC-60068-2-2.)

    Operating humidity

    10% to 90% RH, noncondensing

    Storage humidity

    5% to 95% RH, noncondensing (Tested in accordance with IEC-60068-2-56.)

    Maximum altitude

    2000 m

    Pollution Degree (IEC 60664)


    Indoor use only.


    Operating shock

    30 g peak, half-sine, 11 ms pulse (Tested in accordance with IEC-60068-2-27. Test profile developed in accordance with MIL-PRF-28800F.)

    Random Vibration


    5 Hz to 500 Hz, 0.3 grms


    5 Hz to 500 Hz, 2.4 grms (Tested in accordance with IEC-60068-2-64. Nonoperating test profile exceeds the requirements of MIL-PRF-28800F, Class 3.)


    Isolation Voltages

    Port-to-port ground


    500 Vrms verified by a 5 s dielectric withstand test


    60 VDC, Measurement Category I

    Port-to-earth ground


    500 Vrms verified by a 5 s dielectric withstand test


    60 VDC, Measurement Category I


    This isolation is intended to prevent ground loops.

    Measurement Category I is for measurement performed on circuits not directly connected to the electrical distribution system referred to as MAINS voltage. MAINS is a hazardous live electrical supply system that powers equipment. This category is for measurements of voltages from specially protected secondary circuits. Such voltage measurements include signal levels, special equipment, limited-energy parts of equipment, circuits powered by regulated low-voltage sources, and electronics.


    Do not connect the PXI-8517 to signals or use for measurements within Measurement Categories II, III, or IV.


    Ne connectez pas le PXI-8517 à des signaux et ne l'utilisez pas pour effectuer des mesures dans les catégories de mesure II, III ou IV.


    Measurement Categories CAT I and CAT O (Other) are equivalent. These test and measurement circuits are not intended for direct connection to the MAINs building installations of Measurement Categories CAT II, CAT III, and CAT IV.

    Safety Standards

    This product is designed to meet the requirements of the following standards of safety for information technology equipment:
    • IEC 61010-1, EN 61010-1
    • UL 61010-1, CSA 61010-1

    For UL and other safety certifications, refer to the product label or the Product Certifications and Declarations section.

    Electromagnetic Compatibility

    This product meets the requirements of the following EMC standards for electrical equipment for measurement, control, and laboratory use:

    • EN 61326 (IEC 61326): Class A emissions; Basic immunity
    • EN 55011 (CISPR 11): Group 1, Class A emissions
    • AS/NZS CISPR 11: Group 1, Class A emissions
    • FCC 47 CFR Part 15B: Class A emissions
    • ICES-001: Class A emissions

    For EMC declarations and certifications, and additional information, refer to the Product Certifications and Declarations section.


    For EMC compliance, operate this product according to the documentation.


    When operating this product, use shielded cables and accessories.

    CE Compliance

    This product meets the essential requirements of applicable European Directives, as follows:

    • 2014/35/EU; Low-Voltage Directive (safety)
    • 2014/30/EU; Electromagnetic Compatibility Directive (EMC)

    Product Certifications and Declarations

    Refer to the product Declaration of Conformity (DoC) for additional regulatory compliance information. To obtain product certifications and the DoC for NI products, visit, search by model number, and click the appropriate link.

    Environmental Management

    NI is committed to designing and manufacturing products in an environmentally responsible manner. NI recognizes that eliminating certain hazardous substances from our products is beneficial to the environment and to NI customers.

    For additional environmental information, refer to the Commitment to the Environment web page at This page contains the environmental regulations and directives with which NI complies, as well as other environmental information not included in this document.

    Waste Electrical and Electronic Equipment (WEEE)

    EU Customers  

    At the end of the product life cycle, all NI products must be disposed of according to local laws and regulations. For more information about how to recycle NI products in your region, visit



    National Instruments符合中国电子信息产品中限制使用某些有害物质指令(RoHS)。关于National Instruments中国RoHS合规性信息,请登录。(For information about China RoHS compliance, go to

    Recently Viewed Topics