Table Of Contents


    Last Modified: April 25, 2017

    This section contains specifications for the PXIe-1062Q chassis.


    Specifications are subject to change without notice.


    AC Input

    Input voltage range

    100 to 240 VAC

    Operating voltage range[1]

    90 to 264 VAC

    Input current rating

    8 A

    Input frequency

    50/60 Hz

    Operating frequency range1

    47 to 63 Hz

    Line regulation

    3.3 V


    5 V


    ±12 V



    70% typical

    Power disconnect

    The AC power cable provides main power disconnect. The front-panel power switch causes the internal chassis power supply to provide DC power to the CompactPCI/PXI Express backplane. You also can use the rear-panel D-SUB 9-pin connector and power mode switch to control the internal chassis power supply.

    DC Output

    Table 1. DC current capacity (I mp)
    Voltage Maximum Current
    +3.3 V 32 A
    +5 V 30 A
    +12 V 25 A
    -12 V 1.5 A
    5 VAUX 2 A

    Maximum total usable power is 353.6 W.

    Table 2. Backplane slot current capacity
    Slot +5 V V (I/O) +3.3 V +12 V -12 V 5 VAUX
    System Controller Slot 15 A - 15 A 30 A - 1 A
    System Timing Slot - - 6 A 4 A - 1 A
    Hybrid Peripheral Slot with PXI-1 Peripheral 6 A 5 A 6 A 1 A 1 A -
    Hybrid Peripheral Slot with PXI-5 Peripheral - - 6 A 4 A - 1 A
    PXI-1 Peripheral Slot 6 A 11 A 6 A 1 A 1 A -

    Total system slot current should not exceed 45 A.


    PCI V(I/O) pins in PXI-1 peripheral slots and hybrid peripheral slots are connected to +5 V.


    The maximum power dissipated in the system slot should not exceed 140 W.


    The maximum power dissipated in a peripheral slot should not exceed 38.25 W.

    Table 3. Load regulation
    Voltage Load Regulation
    +3.3 V <5%
    +12 V <5%
    +5 V <5%
    -12 V <5%
    Table 4. Maximum ripple and noise (20 MHz bandwidth)
    Voltage Maximum Ripple and Noise
    +3.3 V 50 mVpp
    +12 V 50 mVpp
    +5 V 50 mVpp
    -12 V 50 mVpp

    Over-current protection

    All outputs protected from short circuit and overload with automatic recovery

    Over-voltage protection, 3.3 V and 5 V

    Clamped at 20 to 30% above nominal output voltage

    Power supply shuttle MTTR

    Replacement in under 5 minutes

    Chassis Cooling

    Module cooling system

    Forced air circulation (positive pressurization) through two 110 cfm fans with High/Auto speed selector

    Slot airflow direction

    Bottom of module to top of module

    Module cooling intake

    Bottom rear of chassis

    Module cooling exhaust

    Along both sides and top of chassis

    Power supply cooling system

    Forced air circulation through integrated fan

    Power supply cooling intake

    Right side of chassis

    Power supply cooling exhaust

    Left side of chassis


    Maximum altitude

    2,000 m (800 mbar) (at 25 °C ambient)

    Pollution Degree


    Indoor use only.

    Operating Environment

    Ambient temperature range

    0 °C to 55 °C (Tested in accordance with IEC-60068-2-1 and IEC-60068-2-2. Meets MIL-PRF-28800F Class 3 low temperature limit and MIL-PRF-28800F Class 2 high temperature limit )

    Relative humidity range

    10% to 90%, noncondensing (Tested to temperature and humidity levels specified in IEC-60068-2-56.)

    Storage Environment

    Ambient temperature range

    –40 °C to 71 °C (Tested in accordance with IEC-60068-2-1 and IEC-60068-2-2. Meets MIL-PRF-28800F Class 3 limits.)

    Relative humidity range

    5% to 95%, noncondensing (Tested in accordance with IEC-60068-2-56.)

    Shock and Vibration

    Operational shock

    30 g peak, half-sine, 11 ms pulse (Tested in accordance with IEC-60068-2-27. Meets MIL-PRF-28800F Class 2 limits.)

    Random Vibration Operating

    5 to 500 Hz, 0.3 grms


    5 to 500 Hz, 2.4 grms (Tested in accordance with IEC-60068-2-64. Nonoperating test profile exceeds the requirements of MIL-PRF-28800F, Class 3.)

    Acoustic Emissions

    Sound Pressure Level (at Operator Position)

    (Tested in accordance with ISO 7779. Meets MIL-PRF-28800F requirements.)

    Auto fan (up to ~30 °C ambient)

    43.6 dBA

    High fan

    62 dBA

    Sound Power

    Auto fan (up to ~30 °C ambient)

    52.8 dBA

    High fan

    72 dBA


    This product is designed to meet the requirements of the following electrical equipment safety standards for measurement, control, and laboratory use:

    • IEC 61010-1, EN 61010-1
    • UL 61010-1, CSA 61010-1

    For UL and other safety certifications, refer to the product label or the Online Product Certification section.

    Electromagnetic Compatibility

    This product meets the requirements of the following EMC standards for electrical equipment for measurement, control, and laboratory use:

    • EN 61326 (IEC 61326): Class A emissions; Basic immunity
    • EN 55011 (CISPR 11): Group 1, Class A emissions
    • AS/NZS CISPR 11: Group 1, Class A emissions
    • FCC 47 CFR Part 15B: Class A emissions
    • ICES-001: Class A emissions

    For the standards applied to assess the EMC of this product, refer to the Online Product Certification section.


    For EMC compliance, operate this device with shielded cabling.

    CE Compliance

    This product meets the essential requirements of applicable European Directives, as follows:
    • 2006/95/EC; Low-Voltage Directive (safety)
    • 2004/108/EC; Electromagnetic Compatibility Directive (EMC)

    Online Product Certification

    Refer to the product Declaration of Conformity (DoC) for additional regulatory compliance information. To obtain product certifications and the DoC for this product, visit, search by model number or product line, and click the appropriate link in the Certification column.

    Environmental Management

    NI is committed to designing and manufacturing products in an environmentally responsible manner. NI recognizes that eliminating certain hazardous substances from our products is beneficial to the environment and to NI customers.

    For additional environmental information, refer to the Minimize Our Environmental Impact web page at This page contains the environmental regulations and directives with which NI complies, as well as other environmental information not included in this document.

    Waste Electrical and Electronic Equipment (WEEE)

    EU Customers  

    At the end of the product life cycle, all NI products must be disposed of according to local laws and regulations. For more information about how to recycle NI products in your region, visit



    National Instruments符合中国电子信息产品中限制使用某些有害物质指令(RoHS)。关于National Instruments中国RoHS合规性信息,请登录。(For information about China RoHS compliance, go to



    3U-sized; one system slot (with three system expansion slots) and seven peripheral slots. Compliant with IEEE 1101.10 mechanical packaging. PXI Express Specification compliant. Accepts both PXI Express and CompactPCI (PICMG 2.0 R 3.0) 3U modules.

    Backplane bare-board material

    UL 94 V-0 Recognized

    Backplane connectors

    Conforms to IEC 917 and IEC 1076-4-101, UL 94 V-0 rated

    10 MHz System Reference Clock: PXI_CLK10

    Maximum slot-to-slot skew

    250 ps


    ±25 ppm max (guaranteed over the operating temperature range)

    Maximum jitter

    5 ps RMS phase-jitter (10 Hz–1 MHz range)


    45% to 55%

    Unloaded signal swing

    3.3 V ±0.3 V


    For other specifications, refer to the PXI-1 Hardware Specification.

    External 10 MHz Reference Out

    (BNC on rear panel of chassis)


    ±25 ppm max (guaranteed over the operating temperature range)

    Maximum jitter

    5 ps RMS phase-jitter (10 Hz to 1 MHz range)

    Output amplitude

    1 VPP ±20% square-wave into 50 Ω, 2 VPP unloaded

    Output impedance

    50 Ω ±5 Ω

    100 MHz System Reference Clock: PXIe_CLK100 and PXIe_SYNC100

    Maximum slot-to-slot skew

    100 ps


    ±25 ppm max (guaranteed over the operating temperature range)

    Maximum jitter

    3 ps RMS phase-jitter (10 Hz to 12 kHz range), 2 ps RMS phase-jitter (12 kHz to 20 MHz range)

    Duty-factor for PXIe_CLK100

    45% to 55%

    Absolute differential voltage (When terminated with a 50 Ω load to 1.30 V or Thévenin equivalent)

    400 to 1000 mV

    Single-ended VOH

    2.0–2.5 V


    For other specifications, refer to the PXI-5 PXI Express Hardware Specification

    External Clock Source


    10 MHz ±100 ppm

    Input amplitude

    Rear panel BNC

    200 mVPP to 5 VPP square-wave or sine-wave

    System timing slot PXI_CLK10_IN

    5 V or 3.3 V TTL signal

    Rear panel BNC input impedance

    50 Ω ±5 Ω

    Maximum jitter introduced by backplane

    1 ps RMS phase-jitter (10 Hz to 1 MHz range)



    3.0 to 5.5 V


    0 to 0.8 V

    PXI Star Trigger

    Maximum slot-to-slot skew

    250 ps

    Backplane characteristic impedance

    65 Ω ±10%

    For other specifications, refer to the PXI-1 Hardware Specification.

    PXI Differential Star Triggers


    Maximum slot-to-slot skew

    150 ps

    Maximum differential skew

    25 ps

    Backplane differential impedance

    100 Ω ±10%

    For other specifications, the NI PXIe-1062Q complies with the PXI-5 PXI Express Hardware Specification.


    Standard chassis dimensions


    6.97 in. (177.1 mm)


    10.68 in. (271.4 mm)


    15.61 in. (396.5 mm)


    0.57 in. (14.5 mm) is added to height when feet are installed. When tilted with front feet extended on table top, height is increased approximately 2.08 in. (52.8 mm) in front and 0.583 in. (14.8 mm) in rear.


    19.4 lb (8.8 kg )

    Chassis materials

    Sheet Aluminum (5052-H32, 3003-H14, and 6061-T6), Extruded Aluminum (6060-T6), and Cold Rolled Steel, PC-ABS, Santoprene, Nylon


    Conductive Clear Iridite on Aluminum Clear Chromate Zinc Plating on Cold Rolled Steel Polyurethane Enamel

    The following figures show the NI PXIe-1062Q chassis dimensions. The holes shown are for the installation of the optional rack mount kits. You can install those kits on the front or rear of the chassis, depending on which end of the chassis you want to face toward the front of the instrument cabinet. Notice that the front and rear chassis mounting holes (size M4) are symmetrical.

    Figure 1. PXIe-1062Q Chassis Dimensions (Front and Side)
    Figure 2. PXIe-1062Q Chassis Dimensions (Bottom)
    Figure 3. NI Chassis Rack Mount Kit Components
    1. Front Rack Mount Kit
    2. PXIe-1062Q Chassis
    3. Rear Rack Mount Kit
    • 1 The operating range is guaranteed by design.

    Recently Viewed Topics