AI.MeasTypes
|
Indicates the measurement types supported by the channel. |
AI.TermCfgs
|
Indicates the list of terminal configurations supported by the channel. |
AI.InputSrcs
|
Indicates the list of input sources supported by the channel. Channels may support using the signal from the I/O connector or one of several calibration signals.
|
AI.SensorPower.Types
|
Indicates the types of power supplied to the sensor supported by this channel. |
AI.SensorPower.VoltageRangeVals
|
Indicates pairs of sensor power voltage ranges supported by this channel. Each pair consists of the low value followed by the high value.
|
AI.PowerControl.Voltage
|
Specifies the voltage level for the sensor's power supply.
|
AI.PowerControl.Enable
|
Specifies whether to turn on the sensor's power supply.
|
AI.PowerControl.Type
|
Specifies the type of power supplied to the sensor. |
AI.SensorPower.OpenChan
|
Indicates whether there is an open channel or undercurrent condition on the channel. |
AI.SensorPower.Overcurrent
|
Indicates whether there is an overcurrent condition on the channel. |
AO.OutputTypes
|
Indicates the output types supported by the channel. |
AO.PowerUpOutputTypes
|
Indicates the power up output types supported by the channel. |
AO.TermCfgs
|
Indicates the list of terminal configurations supported by the channel. |
AO.ManualControl.Enable
|
Specifies if you can control the physical channel externally via a manual control located on the device. You cannot simultaneously control a channel manually and with NI-DAQmx.
|
AO.ManualControl.ShortDetected
|
Indicates whether the physical channel is currently disabled due to a short detected on the channel. |
AO.ManualControl.Amplitude
|
Indicates the current value of the front panel amplitude control for the physical channel in volts. |
AO.ManualControl.Freq
|
Indicates the current value of the front panel frequency control for the physical channel in hertz. |
AO.PowerAmp.ChannelEnable
|
Specifies whether to enable or disable a channel for amplification. This property can also be used to check if a channel is enabled.
|
AO.PowerAmp.ScalingCoeff
|
Indicates the coefficients of a polynomial equation used to scale from pre-amplified values. |
AO.PowerAmp.Overcurrent
|
Indicates if the channel detected an
overcurrent condition.
|
AO.PowerAmp.Gain
|
Indicates the calibrated gain of the channel. |
AO.PowerAmp.Offset
|
Indicates the calibrated offset of the channel in volts. |
DI.PortWidth
|
Indicates in bits the width of digital input port. |
DI.SampClkSupported
|
Indicates if the sample clock timing type is supported for the digital input physical channel. |
DI.SampModes
|
Indicates the sample modes supported by devices that support sample clocked digital input. |
DI.ChangeDetectSupported
|
Indicates if the change detection timing type is supported for the digital input physical channel. |
DO.PortWidth
|
Indicates in bits the width of digital output port. |
DO.SampClkSupported
|
Indicates if the sample clock timing type is supported for the digital output physical channel. |
DO.SampModes
|
Indicates the sample modes supported by devices that support sample clocked digital output. |
CI.MeasTypes
|
Indicates the measurement types supported by the channel. |
CO.OutputTypes
|
Indicates the output types supported by the channel. |
TEDS.MfgID
|
Indicates the manufacturer ID of the sensor. |
TEDS.ModelNum
|
Indicates the model number of the sensor. |
TEDS.SerialNum
|
Indicates the serial number of the sensor. |
TEDS.VersionNum
|
Indicates the version number of the sensor. |
TEDS.VersionLetter
|
Indicates the version letter of the sensor. |
TEDS.BitStream
|
Indicates the TEDS binary bitstream without checksums. |
TEDS.TemplateIDs
|
Indicates the IDs of the templates in the bitstream in
TEDS.BitStream
.
|