Home Support NI Product Manuals FlexLogger 2019 R1 Manual

Table Of Contents

Supported Hardware

Download Manual | Offline Viewer Required
Version:
Last Modified: November 27, 2018

Refer to the following table for a list of hardware devices FlexLogger supports.

spd-note-note
Note  

You can use supported hardware in FlexLogger without a network connection.

NI Product Model Name Notes
CompactDAQ Chassis cDAQ-9171 —
cDAQ-9174 —
cDAQ-9178 —
cDAQ-9179 —
cDAQ-9181 —
cDAQ-9184 —
cDAQ-9185 FlexLogger supports synchronization between TSN-enabled CompactDAQ chassis provided they are a part of your local 802.1AS subnet. Refer to the Using TSN to Synchronize Acquisitions topic for more information.
cDAQ-9188 —
cDAQ-9188XT —
cDAQ-9189 FlexLogger supports synchronization between TSN-enabled CompactDAQ chassis provided they are a part of your local 802.1AS subnet. Refer to the Using TSN to Synchronize Acquisitions topic for more information.
cDAQ-9191 —
C Series Voltage Input Modules NI 9201 —
NI 9202 —
NI 9205 —
NI 9206 —
NI 9209 —
NI 9215 —
NI 9220 —
NI 9221 —
NI 9222 —
NI 9223 —
NI 9224 —
NI 9225 —
NI 9228 —
NI 9229 —
NI 9238 —
NI 9239 —
NI 9242 —
NI 9244 —
NI 9251 —
C Series Voltage Output Modules NI 9263 —
NI 9264 —
NI 9269 —
C Series Current Input Modules NI 9203 —
NI 9208 —
NI 9227 —
NI 9246 —
NI 9247 —
C Series Current Output Modules NI 9265 —
NI 9266 —
C Series Voltage and Current Input Modules NI 9207 —
C Series Sound and Vibration Input Modules NI 9230 —
NI 9231 —
NI 9232 —
NI 9234 —
NI 9250 —
C Series Temperature Input Modules NI 9210 —
NI 9211 —
NI 9212 —
NI 9213 —
NI 9214 —
NI 9216 —
NI 9217 —
NI 9226 —
C Series Universal Analog Input Modules NI 9218 —
NI 9219 —
C Series Strain/Bridge Input Modules NI 9235 —
NI 9236 —
NI 9237 —
C Series Counter Input Module NI 9361
  • FlexLogger does not support pull-up resistor functionality. To enable pull-up resistor functionality, you will need to install an external pull-up resistor on the line.
  • 5 V differential (TTL) and single-ended (RSE) 24 V input are supported. For RSE input, however, FlexLogger does not support changing the input voltage threshold and uses the default level of 2.5 V.
C Series Digital Modules (serial digital I/O) NI 9375
  • The NI 9375must have all lines set to input or to output in a project.
  • You cannot use parallel and serial modules together on the same FlexLogger project unless they are installed in separate cDAQ chassis.
NI 9403
NI 9425
NI 9426
NI 9476
NI 9477
NI 9478
C Series Digital Modules (parallel digital I/O) NI 9344 You cannot use parallel and serial modules together on the same FlexLogger project unless they are installed in separate cDAQ chassis.
NI 9401
NI 9402
NI 9411
NI 9421
NI 9422
NI 9423
NI 9435
NI 9436
NI 9437
NI 9472
NI 9474
NI 9475
NI 9481
NI 9482
NI 9485
C Series CAN and Vehicle Multiprotocol Interface Modules NI 9860 FlexLogger only supports the TRC-8542 and TRC-8543 transceiver cables.
NI 9861 —
NI 9862 —
CAN Interface Devices USB-8502 —
FieldDAQ Voltage Input Bank FD-11601
  • External powered sensor configuration for the FD-11601 cannot be performed in FlexLogger. To configure these settings in MAX, click Show in MAX on the FD-11601 in your FlexLogger Channel Specification.
  • FlexLogger supports synchronization between TSN-enabled FieldDAQ devices provided they are a part of your local 802.1AS subnet. Refer to the Using TSN to Synchronize Acquisitions topic for more information.
FD-11603
FieldDAQ Temperature Input Bank FD-11613
FD-11614
FieldDAQ Strain/Bridge Input Bank FD-11637

Related Topics

Recently Viewed Topics