Setting Up the Two Object Configuration

This section describes the module location and connection sequence for the two object VRTS configuration. This configuration uses two VDG modules and one VST module. Insert the modules into the chassis as shown in the following image. Refer to Installing the Modules for more information about inserting the modules.



To cable your modules, complete steps 1 through 11 in numerical order. Reference the subsequent figure to verify that your modules are properly cabled.

  1. Use one 0.09 m MMPX R/A-SMA R/A to connect the SHORT OUT port of the VDG in slots 4 through 6 to the RF IN port of the VDG in slots 7 through 9.
  2. Use one 0.07 m SMA R/A-SMA R/A cable to connect the SHORT IN port of the VDG in slots 4 through 6 to the RF OUT port of the VDG in slots 7 through 9.
  3. Use one 0.11 m MMPX-MMPX cable to connect the LO OUT port of the VST in slots 3 through 4 into the LO IN port of the same VST.
  4. Use two 0.25 m MMPX-MMPX cables to connect the following modules:
    1. Connect the REF OUT port of the VST in slots 2 through 3 to the REF IN port of the VDG in slots 4 through 6.
    2. Connect the REF OUT port of the VDG in slots 4 through 6 to the REF IN port of the VDG in slots 7 through 9.
  5. Use one 0.20 m SMA-SMA cable to connect the RF OUT port of the VST in slots 2 through 3 to the LONG IN port of the VDG in slots 4 through 6.
  6. Use one 0.30 m MMPX-SMA cable to connect the RF IN port of the VST in slots 2 through 3 to the LONG OUT port of the VDG in slots 4 through 6.
  7. Use one NANOPITCH-MINI HDMI cable to connect the DIO port of the VST in slots 2 through 3 to the DIO IN port of the VDG in slots 4 through 6.
  8. Use one Cable Retention Bracket to secure the DIO port of the VST in slots 2 through 3.
  9. Use one 0.25 m MINI HDMI-MINI HDMI cable to connect the DIO OUT port of the VDG in slots 4 through 6 to the DIO IN port of the VDG in slots 7 through 9.
  10. Use two 0.46 m SMA-SMA cables to connect the following modules:
    1. Connect the RF IN port of the VDG in slots 4 through 6 to the RX IF OUT port of the mmWave Radio Head.
    2. Connect the RF OUT port of the VDG in slots 4 through 6 to the TX IF IN port of the mmWave Radio Head.
  11. Use one 1 m MINI HDMI-MINI HDMI cable to connect the DIO OUT port of the VDG in slots 7 through 9 to the DIO 0 port of the mmWave Radio Head.
    Figure 1. Two Object Cabled Modules


    1. MMPX R/A-SMA R/A, 0.09 m
    2. SMA R/A-SMA R/A, 0.07 m
    3. MMPX-MMPX, 0.11 m
    4. MMPX-MMPX, 0.25 m
    5. SMA-SMA, 0.20 m
    6. MMPX-SMA, 0.30 m
    7. NANOPITCH-MINI HDMI
    8. Cable Retention Bracket
    9. MINI HDMI-MINI HDMI, 0.25 m.
    10. SMA-SMA, 0.46 m
    11. MINI HDMI-MINI HDMI, 1 m