Clear Waveform Measurement Stats
- Updated2023-02-17
- 5 minute(s) read
Clear Waveform Measurement Stats
Clears the waveform statistics on the channel and measurement you specify.
Clears the statistical information and the multi-acquisition array measurements. Every time a measurement is called, the statistics information is updated, including the min, max, mean, standard deviation, and number of updates.
Inputs/Outputs
session in
Handle that identifies the NI-SCOPE instrument session as previously allocated by Initialize With Options .
error in
Error conditions that occur before this node runs.
The node responds to this input according to standard error behavior.
Default value: No error
channels
The channel(s) from which to acquire data.
Channel String Syntax
This input parameter has the following syntax options:
- A single channel, such as 0
- A list of channels, such as 0,1 or 3,2,1,0
- A range of channels, such as 0-7 or 0:7
- A combination of channels from multiple instruments, such as PXI1Slot3/0,PXI1Slot3/2-3,PXI1Slot4/2-3
Note The order of channels in a list is important. The data for each channel is returned in the order the channels occur in the list.
clearable measurement
The measurement for which to clear the statistics.
| All Measurements | 10000 | Clears all measurements. |
| Multi Acq. Voltage Histogram | 4004 | Corresponds to the NISCOPE_VAL_MULTI_ACQ_VOLTAGE_HISTOGRAM C or C++ command. |
| Multi Acq. Time Histogram | 4005 | Corresponds to the NISCOPE_VAL_MULTI_TIME_HISTOGRAM C or C++ command. |
| Multi Acq. Average | 4016 | Corresponds to the NISCOPE_VAL_MULTI_ACQ_AVERAGE C or C++ command. |
| Frequency | 2 | Corresponds to the NISCOPE_VAL_FREQUENCY C or C++ command.1.0 divided by the frequency, in hertz. |
| Average Frequency | 1016 | Corresponds to the NISCOPE_VAL_AVERAGE_FREQUENCY C or C++ command.1.0 divided by the average period. |
| FFT Frequency | 1008 | Corresponds to the NISCOPE_VAL_FFT_FREQUENCY C or C++ command. |
| Period | 3 | Corresponds to the NISCOPE_VAL_PERIOD C or C++ command. |
| Average Period | 1015 | Corresponds to the NISCOPE_VAL_AVERAGE_PERIOD C or C++ command. |
| Rise Time | 0 | Corresponds to the NISCOPE_VAL_RISE_TIME C or C++ command. |
| Fall Time | 1 | Corresponds to the NISCOPE_VAL_FALL_TIME command. |
| Rising Slew Rate | 1010 | Corresponds to the NISCOPE_VAL_RISE_SLEW_RATE C or C++ command. |
| Falling Slew Rate | 1011 | Corresponds to the NISCOPE_VAL_FALL_SLEW_RATE C or C++ command. |
| Overshoot | 18 | Corresponds to the NISCOPE_VAL_OVERSHOOT C or C++ command. |
| Preshoot | 19 | Corresponds to the NISCOPE_VAL_PRESHOOT C or C++ command. |
| Voltage RMS | 4 | Corresponds to the NISCOPE_VAL_VOLTAGE_RMS C or C++ command. |
| Voltage Cycle RMS | 4 | Corresponds to the NISCOPE_VAL_VOLTAGE_CYCLE_RMS C or C++ command. |
| AC Estimate | 1012 | Corresponds to the NISCOPE_VAL_AC_ESTIMATE C or C++ command. |
| FFT Amplitude | 1009 | Corresponds to the NISCOPE_VAL_FFT_AMPLITUDE C or C++ command. |
| Voltage Average | 10 | Corresponds to the NISCOPE_VAL_VOLTAGE_AVERAGE C or C++ command. |
| Voltage Cycle Average | 17 | Corresponds to the NISCOPE_VAL_VOLTAGE_CYCLE_AVERAGE |
| DC Estimate | 1013 | Corresponds to the NISCOPE_VAL_DC_ESTIMATE C or C++ command. |
| Voltage Max | 6 | Corresponds to the NISCOPE_VAL_VOLTAGE_MAX C or C++ command. |
| Voltage Min | 7 | Corresponds to the NISCOPE_VAL_VOLTAGE_MIN C or C++ command. |
| Voltage Peak-to-Peak | 5 | Corresponds to the NISCOPE_VAL_VOLTAGE_PEAK_TO_PEAK C or C++ command. |
| Voltage High | 8 | Corresponds to the NISCOPE_VAL_VOLTAGE_HIGH C or C++ command. |
| Voltage Low | 9 | Corresponds to the NISCOPE_VAL_VOLTAGE_LOW C or C++ command. |
| Voltage Amplitude | 15 | Corresponds to the NISCOPE_VAL_AMPLITUDE C or C++ command. |
| Voltage Top | 1007 | Corresponds to the NISCOPE_VAL_VOLTAGE_TOP C or C++ command. |
| Voltage Base | 1006 | Corresponds to the NISCOPE_VAL_VOLTAGE_BASE C or C++ command. |
| Voltage Base to Top | 1017 | Corresponds to the NISCOPE_VAL_VOLTAGE_BASE_TO_TOP C or C++ command. |
| Negative Width | 11 | Corresponds to the NISCOPE_VAL_WIDTH_NEG C or C++ Command. |
| Positive Width | 12 | Corresponds to the NISCOPE_VAL_WIDTH_POS C or C++ command. |
| Negative Duty Cycle | 13 | Corresponds to the NISCOPE_VAL_DUTY_CYCLE_NEG C or C++ command. |
| Positive Duty Cycle | 14 | Corresponds to the NISCOPE_VAL_DUTY_CYCLE_POS C or C++ command. |
| Integral | 1005 | Corresponds to the NISCOPE_VAL_INTEGRAL C or C++ command. |
| Area | 1003 | Corresponds to the NISCOPE_VAL_AREA C or C++ command. |
| Cycle Area | 1004 | Corresponds to the NISCOPE_VAL_CYCLE_AREA C or C++ command. |
| Time Delay | 1014 | Corresponds to the NISCOPE_VAL_TIME_DELAY C or C++ command |
| Phase Delay | 1018 | Corresponds to the NISCOPE_VAL_PHASE_DELAY C or C++ command. |
| Low Ref Volts | 1000 | Corresponds to the NISCOPE_VAL_LOW_REF_VOLTS C or C++ command. |
| Mid Ref Volts | 1001 | Corresponds to the NISCOPE_VAL_MID_REF_VOLTS C or C++ command. |
| High Ref Volts | 1002 | Corresponds to the NISCOPE_VAL_HIGH_REF_VOLTS C or C++ command. |
| Volt. Hist. Mean | 2000 | Corresponds to the NISCOPE_VAL_VOLTAGE_HISTOGRAM_MEAN C or C++ command. |
| Volt. Hist. Stdev | 2001 | Corresponds to the NISCOPE_VAL_VOLTAGE_HISTOGRAM_STDEV C or C++ command. |
| Volt. Hist. Median | 2003 | Corresponds to the NISCOPE_VAL_VOLTAGE_HISTOGRAM_MEDIAN C or C++ command. |
| Volt. Hist. Mode | 2010 | Corresponds to the NISCOPE_VAL_VOLTAGE_HISTOGRAM_MODE C or C++ command. |
| Volt Hist. Max | 2005 | Corresponds to the NISCOPE_VAL_VOLTAGE_HISTOGRAM_MAX C or C++ command. |
| Volt. Hist. Min | 2006 | Corresponds to the NISCOPE_VAL_VOLTAGE_HISTOGRAM_MIN C or C++ command. |
| Volt. Hist. Peak-to-Peak | 2002 | Corresponds to the NISCOPE_VAL_VOLTAGE_HISTOGRAM_PEAK_TO_PEAK C or C++ command. |
| Volt. Hist. Mean + Stdev | 2007 | Corresponds to the NISCOPE_VAL_VOLTAGE_HISTOGRAM_MEAN_PLUS_STDEV C or C++ command. |
| Volt. Hist. Mean + 2 Stdev | 2008 | Corresponds to the NISCOPE_VAL_VOLTAGE_HISTOGRAM_MEAN_PLUS_2_STDEV C or C++ command. |
| Volt. Hist. Mean + 3 Stdev | 2009 | Corresponds to the NISCOPE_VAL_VOLTAGE_HISTOGRAM_MEAN_PLUS_3_STDEV C or C++ command. |
| Volt. Hist. Hits | 2004 | Corresponds to the NISCOPE_VAL_VOLTAGE_HISTOGRAM_HITS C or C++ command. |
| Volt. Hist. New Hits | 2011 | Corresponds to the NISCOPE_VAL_VOLTAGE_HISTOGRAM_NEW_HITS C or C++ command. |
| Time Hist. Mean | 3000 | Corresponds to the NISCOPE_VAL_TIME_HISTOGRAM_MEAN C or C++ command. |
| Time Hist. Stdev | 3001 | Corresponds to the NISCOPE_VAL_TIME_HISTOGRAM_STDEV C or C++ command. |
| Time Hist. Median | 3003 | Corresponds to the NISCOPE_VAL_TIME_HISTOGRAM_MEDIAN C or C++ command. |
| Time Hist. Mode | 3010 | Corresponds to the NISCOPE_VAL_TIME_HISTOGRAM_MODE C or C++ command. |
| Time Hist. Max | 3005 | Corresponds to the NISCOPE_VAL_TIME_HISTOGRAM_MAX C or C++ command. |
| Time Hist. Min | 3006 | Corresponds to the NISCOPE_VAL_TIME_HISTOGRAM_MIN C or C++ command. |
| Time Hist. Peak-to-Peak | 3002 | Corresponds to the NISCOPE_VAL_TIME_HISTOGRAM_PEAK_TO_PEAK C or C++ command. |
| Time Hist. Mean + Stdev | 3007 | Corresponds to the NISCOPE_VAL_TIME_HISTOGRAM_MEAN_PLUS_STDEV C or C++ command. |
| Time Hist. Mean + 2 Stdev | 3008 | Corresponds to the NISCOPE_VAL_TIME_HISTOGRAM_MEAN_PLUS_2_STDEV C or C++ command. |
| Time Hist. Mean + 3 Stdev | 3009 | Corresponds to the NISCOPE_VAL_TIME_HISTOGRAM_MEAN_PLUS_3_STDEV C or C++ command. |
| Time Hist. Hits | 3004 | Corresponds to the NISCOPE_VAL_TIME_HISTOGRAM_HITS C or C++ command. |
| Time Hist. New Hits | 3011 | Corresponds to the NISCOPE_VAL_TIME_HISTOGRAM_NEW_HITS C or C++ command. |
Default value: All Measurements
session out
Reference to the NI-SCOPE instrument session to pass to the next node in the program.
error out
Error information.
The node produces this output according to standard error behavior.