NI-DCPower .NET fx45 API Reference

Table of Contents

DCPowerOutputSource Properties

  • Updated2024-01-04
  • 5 minute(s) read
DCPowerOutputSource Properties

DCPowerOutputSource Properties

The DCPowerOutputSource type exposes the following members.

Properties

  NameDescription
Public propertyActualPowerAllocation
Gets the power, in watts, the device is sourcing on each active channel if the PowerAllocationMode property is set to Automatic or Manual.
Public propertyAdvancedSequencing
Gets the DCPowerOutputSourceAdvancedSequencing sub-object used to configure the advanced sequence properties of the source unit channel.
Public propertyComplianceLimitSymmetry
Specifies whether compliance limits for current generation and voltage generation for the device are applied symmetrically about 0 V and 0 A or asymmetrically with respect to 0 V and 0 A.
Public propertyConductionVoltageMode
Specifies whether the conduction voltage feature is enabled on the specified channel(s).
Public propertyConductionVoltageOffThreshold
Specifies the minimum voltage, in volts, at the input of the specified channel(s) below which the instrument stops sinking on the specified channel(s) when the conduction voltage feature is enabled.
Public propertyConductionVoltageOnThreshold
Specifies the required minimum voltage, in volts, at the input of the specified channel(s) before the instrument starts sinking on the specified channel(s) when the conduction voltage feature is enabled.
Public propertyCurrent
Gets the DCPowerOutputSourceCurrent sub-object used to configure the current properties of the source unit channel.
Public propertyCustomTransientResponse
Gets the DCPowerOutputSourceCustomTransientResponse sub-object used to configure the custom transient response of the source unit channel.
Public propertyIsSequenceLoopCountFinite
Gets or sets whether a sequence should repeat indefinitely.
Public propertyMergedChannels
Gets or sets the channel(s) to merge with a designated primary channel of an instrument in order to increase the maximum current you can source from the instrument.
Public propertyMode
Gets or sets whether to run a single output point or a sequence for the specified channel(s).
Public propertyOutput
Gets the DCPowerOutputSourceOutput sub-object used to configure the source unit channel output.
Public propertyOutputCapacitance
Gets or sets whether to use a low or high capacitance on the output for the specified channel(s).
Public propertyOutputCutoff
Gets the channel settings that define output cutoffs that, if exceeded, cause the output of the specified channel(s) to be disconnected.
Public propertyOverrangingEnabled
Gets or sets whether NI-DCPower allows setting the voltage level, current level, voltage limit and current limit outside the device specification limits.
Public propertyOvpEnabled
Gets or sets whether to enable or disable overvoltage protection (OVP).
Public propertyOvpLimit
Determines the voltage limit, in volts, beyond which overvoltage protection (OVP) engages. Limit is specified as a positive value, but symmetric positive and negative limits are enforced simultaneously. For example, setting the OVP Limit to 65 will configure the OVP feature to trigger an OVP error if the output exceeds ±65 V.
Public propertyPowerAllocationMode
Gets or sets whether the device sources the power its output configuration requires or a specific wattage you request; gets or sets whether NI-DCPower proactively checks that this sourcing power is within the maximum per-channel and overall sourcing power of the device.
Public propertyPulseBiasDelay
Gets or sets the time, in seconds, when the device generates the PulseCompleteEvent.
Public propertyPulseCurrent
Gets the channel settings when the channel is configured for the PulseCurrent.
Public propertyPulseOffTime
Gets or sets the length, in seconds, of the off phase of a pulse.
Public propertyPulseOnTime
Gets or sets the length, in seconds, of the on phase of a pulse.
Public propertyPulseVoltage
Gets the channel settings when the channel is configured for the PulseVoltage.
Public propertyRequestedPowerAllocation
Gets or sets the power, in watts, to request the device to source from each active channel.
Public propertySequenceLoopCount
Gets or sets the number of times a sequence is run after initiation.
Public propertySequenceStepDeltaTime
Gets or sets the amount of time, in seconds, between the start of two consecutive steps in a sequence.
Public propertySequenceStepDeltaTimeEnabled
Gets or sets whether the SequenceStepDeltaTime property is enabled () or disabled ().
Public propertySourceDelay
Gets or sets the time, in seconds, when the device generates the SourceCompleteEvent.
Public propertyTransientResponse
Gets or sets the transient response.
Public propertyVoltage
Gets the DCPowerOutputSourceVoltage sub-object used to configure the Voltage properties of source unit channel.
Top

See Also

Log in to get a better experience