Analog Video 101

Publish Date: Apr 15, 2011 | 161 Ratings | 4.02 out of 5 |  PDF

Overview

This paper is part of the National Instruments Signal Generator Tutorial and High-Speed Digitizers Tutorial series. Each tutorial in this series teaches you a specific topic of common measurement applications by explaining the theory and giving practical examples. This tutorial covers the fundamentals of video signal measurement and generation.

For additional signal generator concepts, refer to the Signal Generator Fundamentals main page.
For additional high-speed digitizer concepts, refer to the High-Speed Digitizers Fundamentals main page.

Table of Contents

  1. Understanding Composite Video Signals
  2. Parts of the Video Signal
  3. Different Video Formats
  4. Color Coding
  5. Video Levels
  6. Interlaced Scanning Concept
  7. Active Image
  8. Gray Scale Image and Extracted Line Profile
  9. Complete NTSC Frame Scan
  10. Relevant NI Products

1. Understanding Composite Video Signals

A composite video signal is a signal in which all the components required to generate a video signal are embedded in a single signal. The three main components that together form a composite signal are as follows:

  • The luma signal (or luminance) — contains the intensity (brightness or darkness) information of the video image
  • The chroma signal — contains the color information of the video image
  • The synchronization signal — controls the scanning of the signal on a display such as the TV screen

The monochrome composite signal is built of two components: luma (or luminance) and synchronization. This signal, which is usually called the Y signal, is shown in Figure 1.


Figure 1. Monochrome Composite Video Signal (Luma Steps from White to Black)


The chroma signal by itself, which is usually called the C signal, is shown in Figure 2.

Figure 2. Color Information Signal for a Color Bar Line (Including the Color Burst)


The composite color video signal, often called the Color Video, Blank, and Sync (CVBS) signal, is the sum of Y and C, is shown in Figure 3.

CVBS = Y + C

Figure 3. Color Composite Video Signal for a Color Bar Line


The two components Y and C can also be distributed separately as two independent signals. These two signals together are called either Y/C or S-video.

Back to Top

2. Parts of the Video Signal


The signal for a single horizontal video line consists of a horizontal sync signal, back porch, active pixel region, and front porch, as shown in Figure 4.


Figure 4. Parts of the Video Signal


The horizontal sync (HSYNC) signals the beginning of each new video line. It is followed by a back porch, which is used as a reference level to remove any DC components from the floating (AC coupled) video signal. This is accomplished during the clamping interval for monochrome signals, and takes place on the back porch. For composite color signals, the clamping occurs during the horizontal sync pulse because most of the back porch is used for the color burst, which provides information for decoding the color content of the signal. The NI Measurement & Automation Explorer Help includes a description of all the advanced setup parameters for the video signal.

You can incorporate color information along with the monochrome video signal. A composite color signal consists of the standard monochrome signal (RS-170 or CCIR) with the following components added:

  • Color burst: Located on the back porch, this is a high-frequency region, which provides a phase and amplitude reference for the subsequent color information.
  • Chroma signal: This is the actual color information. It consists of two quadrature components modulated onto a carrier at the color burst frequency. The phase and amplitude of these components determine the color content at each pixel.


Another aspect of the video signal is the vertical sync (VSYNC) pulse. This is actually a series of pulses that occurs between fields to signal the monitor to perform a vertical retrace and prepare to scan the next field. There are several lines between each field that contain no active video information. Some contain only HSYNC pulses, while several others contain a series of equalizing and VSYNC pulses. These pulses were defined in the early days of broadcast television and have been part of the standard ever since, although newer hardware technology has eliminated the need for some of the extra pulses. A composite RS-170 interlaced signal is shown in Figure 5, including the vertical sync pulses. For simplicity, a six-line frame is shown:


Figure 5. VSYNC Pulse



It is important to realize that the horizontal size (in pixels) of an image obtained from an analog camera is determined by the rate at which the frame grabber samples each horizontal video line. That rate, in turn, is determined by the vertical line rate and the architecture of the camera. The structure of the camera's CCD array determines the size of each pixel. To avoid distorting the image, you must sample in the horizontal direction at a rate that chops the horizontal active video region into the correct number of pixels. The following is an example with numbers from the RS-170 standard:

Parameters of interest:

  • # of lines/frame: 525 (this includes 485 lines for display; the rest are VSYNC lines for each of the two fields)
  • line frequency: 15.734 kHz
  • line duration: 63.556 µs
  • active horizontal duration: 52.66 µs
  • # active pixels/line: 640


You can make these calculations:

  • Pixel clock (PCLK) frequency (the frequency at which each pixel arrives at the frame grabber):
    640 pixels/line / 52.66 e-6 sec/line = 12.15 e6 pixels/sec (12.15 MHz)
  • Total line length in pixels of active video + timing information (referred to as HCOUNT):
    63.556 e-6 sec * 12.15 e6 pixels/sec = 772 pixels/line
  • Frame rate:
    15.734 e3 lines/sec / 525 lines/frame = 30 frames/sec

Back to Top

3. Different Video Formats

Table 1 describes some characteristics of the standard analog video formats in common use.

NTSC: National Television Standards Committee
PAL: Phase Alteration Line
SECAM: Systeme Electronic Pour Coleur Avec Memoire

Format
Where It Is Used
Mode
Signal Name
Frame Rate, Scanning Speed (frame/sec)
Vertical Line Resolution
Line Rate (lines/sec)
Image Size (WxH) pixels
NTSC North and Central America, Japan Mono RS-170 30 525 15,750 640x480
Color NTSC Color 29.97 525 15,734
PAL Europe (except France), Australia, parts of Africa and South America Mono CCIR 25 405 10,125 768x576
Color PAL Color 25 625 15,625
SECAM France, Eastern Europe, Russia, parts of the Middle East and Africa Mono 25 819 20,475 N/A
Color 25 625 15,625

Table 1. Characteristics of Standard Analog Video Formats

Back to Top

4. Color Coding

For all PAL and NTSC formats, the coding is based on the quadrature amplitude modulation (QAM) concept, where two-color components are amplitude-modulated in quadrature and then combined. The modulation must be decoded, so to keep track of the absolute phase needed to decode the color information, you insert a reference signal, called the color burst, at the beginning of each line, right after the horizontal synchronization pulse (see figures 3 and 4).

For the SECAM format, the two-color components are frequency modulated using two different subcarrier frequencies and are sequentially distributed on alternated video lines. The SECAM format does not need a color burst signal.

Back to Top

5. Video Levels

The video levels define the levels and ranges for the different parts of the video signal. The unit used to define video levels is the IRE (Institute of Radio Engineers). The blanking level refers to 0 IRE and the white level refers to +100 IRE. The blanking level, which is the reference level for the video signal (usually 0 V), is different from the black level if a setup is applied to the signal as shown in Figure 6.


Figure 6. Video Levels


For NTSC, a setup of 7.5 IRE is usually applied, moving the black level to +7.5 IRE. For PAL and SECAM, the black level is aligned with the blanking level at 0 IRE.

Table 3 shows the different video levels depending on the video format.

Video Format
Sync Level
Blanking Level
Black Level
White Level
Peak Level
Burst Amplitude
NTSC
–40 IRE
0 IRE
+7.5 IRE
+100 IRE
+120 IRE
20.0 IRE
PAL
–43 IRE
0 IRE
0 IRE
+100 IRE
+133 IRE
21.5 IRE
SECAM
–43 IRE
0 IRE
0 IRE
+100 IRE
+130 IRE
N/A

Table 2. Video Levels by Format

The analog composite video signal is defined as a voltage source with an output impedance of 75 Ω. The sync-to-white level is normally 1 Vpk-pk when loaded with a 75 Ω resistance. Therefore, the unloaded signal is nominally 2 Vpk-pk.

Back to Top

6. Interlaced Scanning Concept

All composite video systems display the video image on a TV screen using an interlaced scanning technique. Figure 7 shows the interlaced scanning concept.

 


Figure 7. Interlaced Scanning on a TV Screen


The analog video signal includes synchronization pulses that control the scanning line by line from left to right and field by field from top to bottom. The pulses that control the line-by-line scanning are called the horizontal synchronization pulses (H-Sync). The pulses that control the vertical scanning are called the vertical synchronization pulses (V-Sync).

Two interlaced fields compose a complete frame. The first field, called the odd field, scans the odd lines of the video image. The second field, called the even field, scans the even lines of the video image. The process repeats for every frame.

See Also:
When Acquiring an Interlaced Image, What Field Is Taken First Odd or Even?
How Are Odd and Even Fields Differentiated in an Interlaced Video Signal?

Back to Top

7. Active Image

The active video image resulting from the scanning always has an aspect ratio (horizontal/vertical) of 4/3 no matter the video format. The color composite video signal shows that the scanning process requires some additional room on the left and right sides of each line as well as on the top and bottom of the active video image region. This additional room includes the synchronization signals, color bursts, and other format-specific information, like the ITS, which are not part of the active video image. Approximately 90 percent of all the lines and 80 percent of each line can transmit the active image information. The exact values depend on the video format, as shown in Table 3.

Video Format
Lines/Frame
Active Lines
Frame Rate
Line Duration
Active Line Duration
NTSC 525 480/486 29.97 frames/sec 63.55 µs 52.2 µs
PAL/SECAM 625 576 25.00 frames/sec 64.00 µs 52.0 µs

Table 3. Active Video Image Values

"Active Lines" represents the number of lines that are actually used to transmit the image information. For example, only 480 lines out of 525 lines per frame transmit the image information in NTSC. Likewise, on each line, the image information is transmitted only during the active lines sequence, which is shorter than the entire line duration. For example, of 63.55 µs, only 52.2 µs are the active line duration in NTSC. Frame rate is the scanning speed.

Back to Top

8. Gray Scale Image and Extracted Line Profile


The Complete NTSC Frame Scan image in the next section simulates the video display that appears on a television screen if the following conditions are true:

  • The television shows the entire line instead of just the active image part.
  • The television is not interlacing the two fields to form a complete image frame. Instead, it is displaying a progressive scan, line by line, of the entire frame.


The scanning starts (line by line from top to bottom) with a number of lines that represent the vertical synchronization pattern for the odd field. Immediately after the vertical synchronization pattern for the odd field, optional insertion test signals (ITS) are inserted. Finally, the actual odd field active image displays.

The process repeats for the even field, forming the complete frame.

 

Note: Most lines start with a horizontal synchronization pulse followed by the color burst pattern. Then the active image (or the ITS) displays as an intensity change, where a higher signal level corresponds to brighter intensity.

The extracted line profile example at the bottom of figures 8 and 9 shows an actual video signal line extracted from the even field. Refer to "Parts of the Video Signal" above for more information about video levels.

Horizontal synchronization pulses are basically simple negative pulses, which are pulses that dip below the level of the luminance signal. However, the vertical synchronization signals are composed of pulse trains distributed on several lines, and the pulse trains are different for odd and even fields. Figures 8 and 9 show the vertical synchronization patterns for both fields and for the three main video formats.


Figure 8. Vertical Blanking and Synchronization Signal for NTSC



Figure 9. Vertical Blanking and Synchronization Signal for PAL and SECAM

Back to Top

9. Complete NTSC Frame Scan

Figure 10 shows the result of scanning all 525 lines that compose a complete NTSC frame.


Figure 10. Complete NTSC Frame Scan


Figure 10 is a gray-scale image because it represents the intensity graph of the raw NTSC video waveform. The color information is embedded in that waveform and is not yet decoded.

You can see the color burst of the signals on the left side. The dotted pattern represents the intensity graph of the sine tone that is the color burst waveform. After decoding, the color burst, if it were visible on the TV monitor, would appear as a solid color surface.

Back to Top

10. Relevant NI Products

NI Analog Video Analyzer datasheet and pricing

NI Analog Video Generator datasheet and pricing

NI Digital Video Analyzer datasheet and pricing

Back to Top

Bookmark & Share


Ratings

Rate this document

Answered Your Question?
Yes No

Submit