Lesson 4 - Op Amp Filters

Publish Date: May 02, 2012 | 5 Ratings | 1.00 out of 5 |  PDF

Overview

As part of the National Instruments Introduction to NI ELVIS II, NI Multisim, and NI LabVIEW courseware, the labs introduces students to the capabilities of the NI ELVIS II educational design and prototyping platform. Students can explore how NI ELVIS II allows for an easy transition from design, simulation to prototype as it interfaces with both NI Multisim and LabVIEW software.

The courseware includes 11 lab experiments starting with the an introduction to the NI ELVIS environment and steps you through AC circuits to communications. The labs are designed as a starting point for your own curriculum design, demonstrations in the classroom, and method to inspire students to be imaginative and creative in their design projects.

View all of the labs for the Introduction to NI ELVIS II, NI Multisim and NI LabVIEW courseware.

Table of Contents

Goal

Adding a few capacitors and resistors to the basic operational amplifier (op amp) circuit can yield many interesting analog circuits such as active filters, integrators, and differentiators. Filters are used to pass specific frequency bands, integrators are used in proportional control, and differentiators are used in noise suppression and waveform generation circuits.

This lab uses the NI ELVIS II suite of instruments to measure the characteristics of lowpass, highpass, and bandpass filters. Simulate these filters using Multisim with the measured component values. In the lab challenge at the end of this chapter, Multisim is used to design a second order active filter.

 

Table of Contents

  1. Required Components
  2. Exercise 4.1: Measuring the Circuit Component Values
  3. Exercise 4.2: Frequency Response of the Basic Op Amp Circuit
  4. Exercise 4.3: Measuring the Op Amp Frequency Characteristic
  5. Exercise 4.4: Highpass Filter
  6. Exercise 4.5: Lowpass Filter
  7. Exercise 4.6: Bandpass Filter
  8. For Further Study
  9. Multisim Challenge: Design a Second-Order Lowpass Filter
  10. Related Links

 

Required Components

Filenames:

Download the files above to access the courseware pertaining to this lesson that illustrate how the NI ELVIS II can be used with NI Multisim and NI LabVIEW covering a range of tools from introductory level exercises to design challenges.

Figure 4.0. Frequency Characteristics of a BandPass Filter

 

Required Soft Front Panels (SFPs)

Digital multimeter (DMM[W,C])

Function generator (FGEN)

Oscilloscope (Scope)

Impedance analyzer (Imped)

Bode analyzer (Bode)

 

Required Components

10 kW resistor R1, (brown, black, orange)

100 kW resistor Rf, (brown, black, yellow)

1 mF capacitor C1

0.01 mF capacitor Cf

741 op amp

 

Exercise 4.1: Measuring the Circuit Component Values

Complete the following steps to measure the values of the individual components:

 

  1. Launch NI ELVIS II.
  2. Select the DMM icon from the Instrument Measurement strip.
  3. Select DMM[W] to measure the resistors.
  4. Select DMM[C] to measure the capacitors.
  5. Fill in the following information.

R1   ___________ W (10 kW nominal)  

Rf   ___________ W (100 kW nominal)

C1   ___________ mF (1 mf nominal)

Cf   ___________ mF (0.01 mf nominal)

 

  1. Close the DMM.

 

End of Exercise 4.1

 

Exercise 4.2: Frequency Response of the Basic Op Amp Circuit

Complete the following steps to build and perform measurements on an op amp.

 

  1. On the workstation protoboard, build a simple 741 inverting op amp circuit with a gain of 10 as shown in Figure 4.1.

 

Figure 4.1. Schematic Diagram of a 741 Inverting Op Amp Circuit with a Gain of 10

 

The circuit looks like Figure 4.1 on the NI ELVIS II protoboard.

Figure 4.2. 741 Inverting Op Amp Circuit with a Gain of 10 on an NI ELVIS protoboard

 

Note: The op amp uses both the +15 and -15 VDC power supplies. These are found on the protoboard pin sockets labeled as “DC Power Supplies +15V, -15V & GROUND.”

 

  1. Connect the function generator [FGEN] pin socket to the input resistor R1, and the input resistor to the op amp input.
  2. Connect the [Ground] pin socket to pin 3 of the op amp.
  3. Connect the op amp output voltage, Vout, to the oscilloscope BNC input connector [BNC 2 +] and the function generator output to BNC input [BNC 1 +].  Connect the ground to the pin sockets [BNC 1 -] and [BNC 2 -].  Using BNC cables, connect the BNC 1 and BNC 2 sockets to the CH0 and CH1 (respectively) inputs on the left side of the ELVIS.

 

Note: If you do not have BNC Cables, connect the circuit input and output into AI0 and AI1 respectively.

 

  1. From the NI ELVIS II Instrument Launcher strip, select the function generator (FGEN) icon and the oscilloscope (Scope) icon.

 

Note: By default, on the oscilloscope, the Channel 0 Settings Source is set to Scope Ch 0 and the Channel 1 Settings Source is set to Scope Ch 1. These are your op amp input and output signals, respectively. If you used the analog input channels instead, select the appropriate channels in the drop down menu under “Source”.

 

  1. To view the signals, click on the enable boxes.
  2. On the function generator panel, set the following parameters:

 

Waveform:                  Sine wave

Peak Amplitude:         0.2 pp

Frequency:                  1000 Hz

DC Offset:                  0.0 V

 

  1. Check your circuit and then apply power to the NI ELVIS II protoboard.
  2. Click on [Run] for both the FGEN and Scope SFPs.
  3. Set the trigger to Edge, CH 0, Level 0.0 and the Time/Div to 1 ms.
  4. Measure the amplitude of the op amp input (CH 0) and output (CH 1) on the oscilloscope window.

 

Figure 4.3. Inverting Op Amp input and output signals

 

Note the output signal is inverted as expected with respect to the input signal.

 

  1. Calculate the voltage gain (the amplitude ratio, CH1/CH0).
  2. Try a range of frequencies from 100 Hz to 10 kHz.

 

How do your measurements agree with the theoretical gain of (Rf/R1)?

 

Is the ratio still the same at 100 kHz?

 

  1. Close the FGEN and Scope windows.

 

End of Exercise 4.2

 

Exercise 4.3: Measuring the Op Amp Frequency Characteristic

The best way to study the AC characteristic response curve of an op amp is to measure its Bode plot. The Bode plot is basically a plot of gain (dB) and phase (degrees) as a function of log frequency. The transfer function for an inverting op amp circuit is given by:

 

Vout = - (Rf/R1) V1

 

where Vout is the op amp output and V1 is the circuit input. The gain is the quantity (Rf/R1). The minus sign inverts the output signal with respect to the input signal. On a Bode plot, one expects a straight line with a magnitude of 20 x log (gain). For a gain of 10, the Bode amplitude should be 20 dB.

 

Complete the following step to measure the Bode plot of the Op Amp circuit:

 

  1. From the NI ELVIS II Instrument Launcher strip, select Bode Analyzer (Bode) icon.
  2. Connect the signals, input (V1) and output (Vout), to the analog input pins as follows:

 

V1+                 AI 0+ (from the FGEN output)

V1 -                 AI 0-   (from GROUND)

 

Vout+               AI 1+  (from the op amp output)

Vout -               AI 1 -   (from GROUND)

 

  1. On the Bode analyzer, set the scan parameters as follows:

 

Start:               5 (Hz)

Stop:                20000 (Hz)

Steps:              10 (per decade)

 

  1. Apply power to the protoboard.
  2. Click [Run] and observe the Bode plot for the inverting op amp circuit.
  3. Take a close look at the phase response.

Figure 4.4. Bode Plot Measurements of an Inverting Op Amp with a gain of 10

 

The gain (20 dB) is flat and independent of frequency until approximately 10,000 Hz, where it starts to roll off as shown in Figure 4.4. This Bode plot is typical for a 741 op amp inverting circuit. At high frequencies, the amplifier response depends on its internal circuitry as well as any external components.

 

End of Exercise 4.3

 

Exercise 4.4: Highpass Filter

A low frequency cutoff point, fL, for a simple RC series circuit is given by the equation:

 

2pfL = 1/RC

 

where fL is measured in hertz. The low-frequency cutoff point is the frequency where the gain (dB) has fallen by -3 dB. This (-3 dB) point occurs when the impedance of the capacitor equals that of the resistor.

 

  1. Add a 1 mF capacitor, Cl, in series with the 1 kW input resistor, R1, in the op amp circuit as shown in Figure 4.5.

Figure 4.5. Highpass Op Amp Filter Circuit Design

 

The highpass op amp filter equation has a low-frequency cutoff point, fL, where the gain has fallen to -3 dB. In other words, when Xc = R:

                                                    2pfL = 1/ R1C1

 

Figure 4.6 shows this circuit on an NI ELVIS protoboard.

 

 

Figure 4.6. Highpass Op Amp Filter on NI ELVIS protoboard

 

  1. Run a second Bode plot using the same scan parameters as in Exercise 4.3.
  2. Observe that the low-frequency response is attenuated while the high-frequency response is similar to the basic op amp Bode plot.

 

Figure 4.7. Bode Measurement of Highpass Op Amp circuit

 

  1. Use the cursor function to find the low-frequency cutoff point, that is, the frequency at which the amplitude has fallen by -3 dB or the phase change is 45 degrees.
  2. Compare your results with the following theoretical predication:

 

2pfL = 1/ R1C1

 

End of Exercise 4.4

 

Exercise 4.5: Lowpass Filter

The high-frequency roll-off in the op amp circuit is due to the internal capacitance of the 741 chip being in parallel with the feedback resistor, Rf. If you add an external capacitor, Cf, in parallel with the feedback resistor, Rf, you can reduce the upper frequency cutoff point. It turns out that you can predict this new cutoff point from the following equation:

 

2pfU = 1/Rf Cf

 

Complete the following steps to perform an additional frequency measurement on the op amp circuit:

 

  1. Short the input capacitor (do not remove it because you will use it in Exercise 4.6).
  2. Add the feedback capacitor, Cf, (0.01 mf) in parallel with the 100 kW feedback resistor.

 

 

Figure 4.8.  Lowpass Op Amp Filter Circuit Design

 

3.   Run a third Bode plot using the same scan parameters.

 

 

Figure 4.9. Bode Measurement of Lowpass Op Amp circuit

 

Figure 4.9 shows that the high-frequency response is attenuated much more than the basic op amp response.

 

  1. Use the cursor function to find the high-frequency cutoff point, that is, the frequency at which the amplitude has fallen by -3 dB or the phase change is 45 degrees.
  2.  Compare your results with the following theoretical prediction:

 

2pfU = 1/ Rf C

 

Note: the 90-degree phase change from the very low-frequency range to the upper-frequency range. This is as expected for a single-pole RC filter stage.

 

End of Exercise 4.5

 

Exercise 4.6: Bandpass Filter

If you allow both an input capacitor and a feedback capacitor in the op amp circuit, the response curve has both a low-cutoff frequency, fL, and a high-cutoff frequency, fU. The frequency range (fU – f L) is called the bandwidth. For example, a good stereo amplifier has a bandwidth of at least 20,000 Hz.

 

Figure 4.10 shows a bandpass filter on an NI ELVIS II protoboard.

 

 

Figure 4.10. Bandpass Op Amp circuit on NI ELVIS protoboard

 

  1. Remove the short on C1.

                         

 

Figure 4.11. Bandpass Op Amp Filter Circuit Design

 

2.    Run a fourth Bode plot using the same scan parameters.

 

    

Figure 4.12. Bode Measurement of Bandpass Op Amp circuit

 

Using the cursors, draw a line between the -3 dB points. All frequencies with an amplitude above this line are contained within the frequency pass band.

 

How does this bandwidth measurement agree with the theoretical prediction of (fU – fL)?

 

End of Exercise 4.6

 

For Further Study

The generalized op amp transfer curve is given by the following phasor equation

 

 Vout = (Zf/Z1)Vin

 

where the impedance values for the four circuits are:

 

 Op Amp Zf  Z1 Gain
Basic Rf  R1  Rf /R1
Highpass Rf     R1 + X C1 Rf /(R1 + XC1)
Lowpass Rf + X Cf R1 (Rf + XCf)/R1
Bandpass Rf + X Cf  R1 + XC1 (Rf + XCf)/(R1 + XC1)

Table 4.0. Impedance Values for the FourOp Amp Circuits

 

At any frequency, you can use the impedance analyzer (Imped) to measure the impedances Zf and Z1. A LabVIEW program can calculate the ratio of two complex numbers. The magnitude of the ratio |Zf/Z1| is the gain.

 

Note: You could also use the impedance analyzer to find the frequencies where R1 equals XC1 and Rf equals XCf  to verify that the lower- and upper-frequency cutoff points from the Bode plot are equal to these frequencies.

           

Multisim Challenge: Design a Second-Order Lowpass Filter

In Exercise 4.5, you built a lowpass filter with a single capacitor in the feedback loop. At high frequencies beyond the cutoff point, the gain falls off linearly with a slope of 6 dB/octave. Some applications require a sharper roll-off. You can accomplish this using a filter design with two or more capacitors in the filter design.

 

  1. Design a second-order lowpass filter with a -3 dB cutoff point, fc, at 1000 Hz.

 

 

Figure 4.13. Multisim solution of a Second-order Op Amp Filter

 

 

This filter has two cutoff points

 

fc1 = (R1||R2)/(2pC1)     and   fc2 =  (2pR3C2)-1

 

            In the special case when fc1 = fc2 = fc, the gain expression for this filter becomes

 

                                                         -R3/(R1+R2)

                                             |G| =    ----------------

                                                            1+(f/fc)2

 

  1. Pick resistors and capacitors to satisfy the special case requirement that

                                               

fc1 = fc2 = 1000 Hz

 

  1. Launch the Multisim program Two Pole Active Filter.
  2. Double-click on the Bode analyzer icon to open a results window.
  3. Run this program and view the Bode plot.

 

      

Figure 4.14. Frequency Response of a Second-order Op Amp Filter

 

  1. From the graph of the gain, estimate the slope of the roll-off curve (should be 40 dB/decade).
  2. Modify this program with your component values.
  3. Compare the slope of the roll-off curve with the previous result in Exercise 4.5 for a single-pole lowpass filter.
  4. If you have the time and components, try building a real two-pole circuit on the NI ELVIS II protoboard.

 

How well does the Bode plot of the theoretical design match your real circuit? Refer to the Lab 3 Multisim Challenge to recall how to overlay in Excel a theoretical design curve with a measured real curve.

 

Related Links

  1. Go back to Lesson 3 - AC Circuit Tools, part of the Introduction to NI ELVIS II, NI Multisim and NI LabVIEW Courseware
  2. Go on to Lesson 5 - Digitial I/O, part of the Introduction to NI ELVIS II, NI Multisim and NI LabVIEW Courseware
  3. Back to the Introduction to NI ELVIS II, NI Multisim, and NI LabVIEW Courseware
  4. Watch this introductory NI ELVIS II video to learn more about the education design and prototyping platform
  5. Find more courseware on NI ELVIS II, NI LabVIEW, and NI Multisim

 

Back to Top

Bookmark & Share

Ratings

Rate this document

Answered Your Question?
Yes No

Submit